Texas Instruments X-Loader 1.41 (Sep 1 2010 - 13:43:00) mmc read: Invalid size Starting OS Bootloader from MMC/SD1 ... U-Boot 1.1.4-gcebe815a-dirty (Aug 16 2010 - 10:34:46) Load address: 0x80e80000 DRAM: 512 MB Flash: 0 kB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: KS8851SNL Hit any key to stop autoboot: 3  2  1  0 mmc read: Invalid size 3152328 bytes read ## Booting image at 80300000 ... Image Name: Linux-3.4.0-rc2-00069-g414e412 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3152264 Bytes = 3 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.0-rc2-00069-g414e412 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Tue May 8 17:34:59 MDT 2012 [ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP4 Panda board [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] OMAP4430 ES2.0 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0f70000 s11456 r8192 d13120 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117346 [ 0.000000] Kernel command line: root=/dev/mmcblk0p2 ro rootwait mem=463M console=ttyO2,115200n8 init=/linuxrc earlyprintk [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 462MB = 462MB total [ 0.000000] Memory: 456820k/456820k available, 17292k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdd000000 - 0xff000000 ( 544 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdcf00000 ( 463 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0591c34 (5672 kB) [ 0.000000] .init : 0xc0592000 - 0xc05decc0 ( 308 kB) [ 0.000000] .data : 0xc05e0000 - 0xc0672958 ( 587 kB) [ 0.000000] .bss : 0xc067297c - 0xc0bc6ba0 (5457 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:474 [ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck. [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.001190] Calibrating delay loop... 2007.19 BogoMIPS (lpj=7839744) [ 0.124938] pid_max: default: 32768 minimum: 301 [ 0.126037] Security Framework initialized [ 0.126464] Mount-cache hash table entries: 512 [ 0.132202] CPU: Testing write buffer coherency: ok [ 0.133697] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.134155] Setting up static identity map for 0x803e89f0 - 0x803e8a60 [ 0.134246] L310 cache controller enabled [ 0.134277] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B [ 0.137268] CPU1: Booted secondary processor [ 0.204406] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.204467] CPU1: Unknown IPI message 0x1 [ 0.204620] Brought up 2 CPUs [ 0.204620] SMP: Total of 2 processors activated (4022.78 BogoMIPS). [ 0.213928] omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck. [ 0.213958] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck. [ 0.214172] omap_hwmod: sys_32k_ck: missing clockdomain for sys_32k_ck. [ 0.214355] omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck. [ 0.214385] omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck. [ 0.217803] omap_hwmod: l3_instr: _wait_target_disable failed [ 0.220672] omap_hwmod: usb_host_fs: _wait_target_disable failed [ 0.223327] omap_hwmod: aess: _wait_target_disable failed [ 0.226043] omap_hwmod: sl2if: cannot be enabled for reset (3) [ 0.230010] omap_hwmod: mcpdm: cannot be enabled for reset (3) [ 0.234710] dummy: [ 0.235870] NET: Registered protocol family 16 [ 0.236572] GPMC revision 6.0 [ 0.241851] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.242126] OMAP GPIO hardware version 0.1 [ 0.242645] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.243377] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.244110] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.244812] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.245513] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.249176] omap_mux_init: Add partition: #1: core, flags: 2 [ 0.250762] omap_mux_init: Add partition: #2: wkup, flags: 2 [ 0.250915] error setting wl12xx data: -38 [ 0.254516] _omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [ 0.254547] _omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [ 0.254547] omap_hwmod_mux_init: Could not allocate device mux entry [ 0.261230] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.261260] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.270141] OMAP DMA hardware revision 0.0 [ 0.298980] bio: create slab at 0 [ 0.300994] vwl1271: 1800 mV [ 0.303588] SCSI subsystem initialized [ 0.304718] omap2_mcspi omap2_mcspi.1: master is unqueued, this is deprecated [ 0.305328] omap2_mcspi omap2_mcspi.2: master is unqueued, this is deprecated [ 0.305877] omap2_mcspi omap2_mcspi.3: master is unqueued, this is deprecated [ 0.306488] omap2_mcspi omap2_mcspi.4: master is unqueued, this is deprecated [ 0.307891] usbcore: registered new interface driver usbfs [ 0.308349] usbcore: registered new interface driver hub [ 0.308654] usbcore: registered new device driver usb [ 0.321868] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz [ 0.324035] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 0.325012] twl 1-0048: PIH (irq 39) chaining IRQs 352..372 [ 0.326538] VUSB: 3300 mV normal standby [ 0.327758] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby [ 0.328948] VPP: 1800 <--> 2500 mV at 1900 mV normal standby [ 0.330322] VCXIO: 1800 mV normal standby [ 0.331176] VDAC: 1800 mV normal standby [ 0.332153] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby [ 0.333343] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby [ 0.334350] CLK32KG: [ 0.335205] VANA: 2100 mV normal standby [ 0.345153] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz [ 0.360717] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.376342] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz [ 0.380432] Switching to clocksource 32k_counter [ 0.436706] NET: Registered protocol family 2 [ 0.437286] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.438598] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.439086] TCP bind hash table entries: 16384 (order: 7, 589824 bytes) [ 0.442993] TCP: Hash tables configured (established 16384 bind 16384) [ 0.443145] TCP: reno registered [ 0.443267] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.443420] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.444091] NET: Registered protocol family 1 [ 0.445159] RPC: Registered named UNIX socket transport module. [ 0.445159] RPC: Registered udp transport module. [ 0.445190] RPC: Registered tcp transport module. [ 0.445190] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.445831] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.572937] VFS: Disk quotas dquot_6.5.2 [ 0.573181] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.574157] NFS: Registering the id_resolver key type [ 0.575012] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.575653] msgmni has been set to 892 [ 0.577880] io scheduler noop registered [ 0.577880] io scheduler deadline registered [ 0.578033] io scheduler cfq registered (default) [ 0.579681] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.582946] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0 [ 0.584167] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1 [ 0.584838] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2 [ 1.387695] console [ttyO2] enabled [ 1.392150] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3 [ 1.416259] brd: module loaded [ 1.429473] loop: module loaded [ 1.435882] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.443023] OneNAND driver initializing [ 1.450683] usbcore: registered new interface driver asix [ 1.456787] usbcore: registered new interface driver cdc_ether [ 1.463226] usbcore: registered new interface driver net1080 [ 1.469573] usbcore: registered new interface driver cdc_subset [ 1.476043] usbcore: registered new interface driver zaurus [ 1.482177] usbcore: registered new interface driver cdc_ncm [ 1.489288] usbcore: registered new interface driver cdc_wdm [ 1.495300] Initializing USB Mass Storage driver... [ 1.500701] usbcore: registered new interface driver usb-storage [ 1.507110] USB Mass Storage support registered. [ 1.512451] usbcore: registered new interface driver libusual [ 1.518768] usbcore: registered new interface driver usbtest [ 1.524749] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) [ 1.532775] mousedev: PS/2 mouse device common for all mice [ 1.541778] twl_rtc twl_rtc: Enabling TWL-RTC [ 1.549133] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 1.556182] i2c /dev entries driver [ 1.562072] Driver for 1-wire Dallas network protocol. [ 1.569366] omap_wdt: OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec [ 1.586456] usbcore: registered new interface driver usbhid [ 1.592437] usbhid: USB HID core driver [ 1.596466] oprofile: hardware counters not available [ 1.601776] oprofile: using timer interrupt. [ 1.606872] TCP: cubic registered [ 1.610351] Initializing XFRM netlink socket [ 1.614929] NET: Registered protocol family 17 [ 1.619659] NET: Registered protocol family 15 [ 1.624603] Registering the dns_resolver key type [ 1.629730] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1 [ 1.637817] ThumbEE CPU extension supported. [ 1.647827] omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0). [ 1.656219] omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0). [ 1.665618] Power Management for TI OMAP4. [ 1.688598] clock: disabling unused clocks to save power [ 1.696990] VANA: incomplete constraints, leaving on [ 1.703674] VDAC: incomplete constraints, leaving on [ 1.711273] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:21 UTC (946684821) [ 1.722106] Waiting for root device /dev/mmcblk0p2... [ 1.802093] mmc0: host does not support reading read-only switch. assuming write-enable. [ 1.810760] mmc0: new SD card at address e624 [ 1.816833] mmcblk0: mmc0:e624 SD02G 1.89 GiB [ 1.825439] mmcblk0: p1 p2 [ 1.845428] EXT3-fs (mmcblk0p2): recovery required on readonly filesystem [ 1.852600] EXT3-fs (mmcblk0p2): write access will be enabled during recovery [ 1.862609] kjournald starting. Commit interval 5 seconds [ 1.872497] EXT3-fs (mmcblk0p2): recovery complete [ 1.877532] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 1.885040] VFS: Mounted root (ext3 filesystem) readonly on device 179:2. [ 1.892578] Freeing init memory: 304K [ 1.898925] Failed to execute /linuxrc. Attempting defaults... modprobe: FATAL: Could not load /lib/modules/3.4.0-rc2-00069-g414e412/modules.dep: No such file or directory INIT: version 2.88 booting Using makefile-style concurrent boot in runlevel S. Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...done. Activating swap...done. [ 3.875854] EXT3-fs (mmcblk0p2): using internal journal Cleaning up ifupdown.... Setting up networking.... Loading kernel modules...done. Activating lvm and md swap...done. Checking file systems...fsck from util-linux 2.19.1 done. Mounting local filesystems...done. Activating swapfile swap...done. Cleaning up temporary files.... Configuring network interfaces...done. Cleaning up temporary files.... Setting kernel variables ...done. INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Debian GNU/Linux wheezy/sid armel ttyO2 armel login: Debian GNU/Linux wheezy/sid armel ttyO2 armel login: root Last login: Sat Jan 1 00:02:01 UTC 2000 on ttyO2 Linux armel 3.4.0-rc2-00069-g414e412 #1 SMP Tue May 8 17:34:59 MDT 2012 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@armel:~# echo enabled > /sys/devices/platform/omap_uart.2/tty/ttyO2/power/w akeup root@armel:~# echo enabled > /sys/devices/platform/omap_uart.2/power/wakeup root@armel:~# echo mem > /sys/power/state [ 66.209167] PM: Syncing filesystems ... done. [ 66.837890] Freezing user space processes ... (elapsed 0.02 seconds) done. [ 66.867980] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done. [ 66.899230] Suspending console(s) (use no_console_suspend to debug) [ 66.915527] PM: suspend of devices complete after 8.057 msecs [ 66.916320] PM: late suspend of devices complete after 0.762 msecs [ 66.918457] PM: noirq suspend of devices complete after 2.105 msecs [ 66.918518] Disabling non-boot CPUs ... [ 66.921874] CPU1: shutdown [ 67.398834] Successfully put all powerdomains to target state [ 67.398986] Enabling non-boot CPUs ... [ 67.401275] CPU1: Booted secondary processor [ 67.401885] CPU1 is up [ 67.403137] PM: noirq resume of devices complete after 1.220 msecs [ 67.404663] PM: early resume of devices complete after 0.762 msecs [ 67.570068] PM: resume of devices complete after 165.405 msecs [ 67.633819] Restarting tasks ... done. root@armel:~# root@armel:~# echo mem > /sys/power/state [ 70.002899] PM: Syncing filesystems ... done. [ 70.008972] Freezing user space processes ... (elapsed 0.02 seconds) done. [ 70.036315] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done. [ 70.067535] Suspending console(s) (use no_console_suspend to debug) [ 70.082305] PM: suspend of devices complete after 6.683 msecs [ 70.083068] PM: late suspend of devices complete after 0.732 msecs [ 70.084808] PM: noirq suspend of devices complete after 1.739 msecs [ 70.084838] Disabling non-boot CPUs ... [ 70.086669] CPU1: shutdown [ 70.602752] Successfully put all powerdomains to target state [ 70.602844] Enabling non-boot CPUs ... [ 70.605041] CPU1: Booted secondary processor [ 70.605560] CPU1 is up [ 70.606719] PM: noirq resume of devices complete after 1.098 msecs [ 70.608154] PM: early resume of devices complete after 0.762 msecs [ 70.772430] PM: resume of devices complete after 164.245 msecs [ 70.836181] Restarting tasks ... done. root@armel:~# root@armel:~# root@armel:~# cat /debug/pm_debug/count cefuse_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0 always_on_core_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:0,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0 cm_clkdm->core_pwrdm (0) prm_clkdm->wkup_pwrdm (0) l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (4) l3_dss_clkdm->dss_pwrdm (1) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (2) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (4) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (3) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (10) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) root@armel:~# echo 1000 > /sys/devices/platform/omap_uart.0/power/autosuspend_de lay_ms _uart.3/power/autosuspend_delay_ms root@armel:~# echo 1000 > /sys/devices/platform/omap_uart.1/power/autosuspend_de lay_ms root@armel:~# echo 1000 > /sys/devices/platform/omap_uart.2/power/autosuspend_de lay_ms root@armel:~# echo 1000 > /sys/devices/platform/omap_uart.3/power/autosuspend_de lay_ms root@armel:~# cat /debug/pm_debug/counHcefuse_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0 always_on_core_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:0,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0 cm_clkdm->core_pwrdm (0) prm_clkdm->wkup_pwrdm (0) l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (4) l3_dss_clkdm->dss_pwrdm (1) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (2) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (4) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (3) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (2) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefɑ(0) root@armel:~#