$ ÿNOLO X-Loader (v1.1.16, Oct 31 2008) Secondary image size 99036 Booting secondary Nokia OMAP Loader v1.1.16 (Oct 31 2008) running on Nokia N800 F5 (RX-34) Clocks: Core: 658 MHz L3: 109 MHz L4: 109 MHz MPU: 329 MHz DSP: 219 MHz IVA: 109 MHz I2C v3.4 Menelaus v2.2 found Vilma v1.5 found Betty v2.1 found Reset reason: pwr_key System DMA v2.0 OneNAND blocks unlocked in 30264 us Flash id: ec4811 Partition table successfully read McSPI v1.4 RFBI version 1.0 Detecting LCD panel lph8923 Panel ID: 838f48 URAL panel detected Detected LCD panel: ls041y3 S1D13745 Hailstorm detected FB memory blanking took 242 ms (3089 kB/s) Logo drawn in 24 ms (1218 kB/s) Über-cool backlight fade-in took 101 ms Prompt keypress detected Initializing USB No USB host detected nolo> usb Initializing USB Entering USB loop SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 64 bytes) SETUP: WR STD DEVICE SET_ADDRESS value 0011 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 18 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 9 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 94 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 00, index 0000, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 02, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 01, index 0409, length 255 bytes) SETUP: WR STD DEVICE SET_CONFIGURATION value 0001 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 03, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0001 index 0002 length 0000 Flashing interface selected SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 Flashing mode entered SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 SETUP: RD VND DEVICE req 04 value 0000 index 0000 length 0200 SETUP: RD VND DEVICE req 03 value 0000 index 0000 length 0004 SETUP: WR VND DEVICE req 12 value 0000 index 0000 length 0012 SETUP: RD VND DEVICE req 14 value 0000 index 0000 length 0200 SETUP: WR VND DEVICE req 42 value 0000 index 0000 length 001b Receiving kernel (length 2061568) Image successfully received SETUP: WR VND DEVICE req 82 value 0000 index 0000 length 0000 SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 Boot requested Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.0-rc2-00059-g0135f6a (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Tue May 8 00:00:12 MDT 2012 [ 0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Nokia N800 [ 0.000000] Ignoring unrecognised tag 0x414f4d50 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c0413a10, node_mem_map c0937000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] OMAP2420 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttyO2,115200 earlyprintk debug init=/bin/bash [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 120464k/120464k available, 10608k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc03a32c0 (3693 kB) [ 0.000000] .init : 0xc03a4000 - 0xc03cb000 ( 156 kB) [ 0.000000] .data : 0xc03cc000 - 0xc0414140 ( 289 kB) [ 0.000000] .bss : 0xc0414164 - 0xc0936428 (5257 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] NR_IRQS:474 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.058624] Calibrating delay loop... 327.68 BogoMIPS (lpj=1277952) [ 0.114044] pid_max: default: 32768 minimum: 301 [ 0.119873] Security Framework initialized [ 0.124572] Mount-cache hash table entries: 512 [ 0.139831] CPU: Testing write buffer coherency: ok [ 0.147216] hw perfevents: enabled with v6 PMU driver, 3 counters available [ 0.154998] Setting up static identity map for 0x80292410 - 0x8029246c [ 0.175872] ttyO2 used as console in debug mode uart2 clocks will not be gated [ 0.204101] dummy: [ 0.209808] GPMC revision 2.0 [ 0.233184] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.240905] OMAP GPIO hardware version 1.8 [ 0.248138] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.258453] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.268737] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.291107] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.318176] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.327362] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.336517] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.345642] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.354766] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.363891] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.373016] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.380157] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.422576] OMAP DMA hardware revision 2.0 [ 0.541473] bio: create slab at 0 [ 0.564575] SCSI subsystem initialized [ 0.573364] omap2_mcspi omap2_mcspi.1: master is unqueued, this is deprecated [ 0.583953] omap2_mcspi omap2_mcspi.2: master is unqueued, this is deprecated [ 0.600677] usbcore: registered new interface driver usbfs [ 0.609405] usbcore: registered new interface driver hub [ 0.617126] usbcore: registered new device driver usb [ 0.628540] omap_i2c omap_i2c.1: bus 1 rev1.3.4 at 400 kHz [ 0.641204] omap_i2c omap_i2c.2: bus 2 rev1.3.4 at 400 kHz [ 0.658996] Switching to clocksource 32k_counter [ 0.808563] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.846862] VFS: Disk quotas dquot_6.5.2 [ 0.851257] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.861541] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.871337] msgmni has been set to 235 [ 0.885040] io scheduler noop registered [ 0.889221] io scheduler deadline registered [ 0.894226] io scheduler cfq registered (default) [ 0.912506] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.935729] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 0.948272] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 0.959106] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 74) is a OMAP UART2 [ 0.967346] console [ttyO2] enabled, bootconsole disabled [ 0.967346] console [ttyO2] enabled, bootconsole disabled [ 0.990051] omap_rng omap_rng: OMAP Random Number Generator ver. 40 [ 1.073852] brd: module loaded [ 1.122009] loop: module loaded [ 1.129333] Menelaus rev 2.2 [ 1.162689] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.172302] OneNAND driver initializing [ 1.178070] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c8880000, freq 54 MHz [ 1.189636] OneNAND Manufacturer: Samsung (0xec) [ 1.194549] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48) [ 1.200195] OneNAND version = 0x0011 [ 1.204071] Chip support all block unlock [ 1.208557] onenand_wait: controller error! state 15 ctrl 0x0440 intr 0x8000 [ 1.217742] Scanning device for bad blocks [ 1.230133] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x39 addr8 0x0 [ 1.238586] OneNAND eraseblock 57 is an initial bad block [ 1.244476] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3a addr8 0x0 [ 1.252868] OneNAND eraseblock 58 is an initial bad block [ 1.258728] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3b addr8 0x0 [ 1.267150] OneNAND eraseblock 59 is an initial bad block [ 1.285644] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xa7 addr8 0x0 [ 1.294036] OneNAND eraseblock 167 is an initial bad block [ 1.301544] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xb5 addr8 0x0 [ 1.309967] OneNAND eraseblock 181 is an initial bad block [ 1.348724] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x1c9 addr8 0x0 [ 1.357238] OneNAND eraseblock 457 is an initial bad block [ 1.555969] Creating 5 MTD partitions on "omap2-onenand": [ 1.561737] 0x000000000000-0x000000020000 : "bootloader" [ 1.583129] 0x000000020000-0x000000080000 : "config" [ 1.599700] 0x000000080000-0x000000280000 : "kernel" [ 1.615692] 0x000000280000-0x000000680000 : "initfs" [ 1.631774] 0x000000680000-0x000010000000 : "rootfs" [ 1.680084] usbcore: registered new interface driver cdc_wdm [ 1.686126] Initializing USB Mass Storage driver... [ 1.693054] usbcore: registered new interface driver usb-storage [ 1.699584] USB Mass Storage support registered. [ 1.707427] usbcore: registered new interface driver libusual [ 1.715332] usbcore: registered new interface driver usbtest [ 1.721527] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) [ 1.736541] mousedev: PS/2 mouse device common for all mice [ 1.754821] i2c /dev entries driver [ 1.766296] Driver for 1-wire Dallas network protocol. [ 1.779785] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec [ 1.894317] usbcore: registered new interface driver usbhid [ 1.900421] usbhid: USB HID core driver [ 1.904785] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 1.913360] mux: Failed to setup hwmod io irq -22 [ 1.931060] Power Management for OMAP2 initializing [ 1.936279] PRCM revision 1.0 [ 1.976257] clock: disabling unused clocks to save power [ 1.984527] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.002685] /home/paul/linux/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.020233] Waiting for root device /dev/mmcblk0p1... [ 2.132843] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.145141] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.151733] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.158325] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.164916] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.814910] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.824188] mmc0: new SDHC card at address 1234 [ 2.834411] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 2.853820] mmcblk0: p1 [ 2.941619] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.951141] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.974761] mmci-omap mmci-omap.0: command timeout (CMD8) [ 3.214782] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.223449] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.231323] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.466369] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.473236] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.480163] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.487121] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.493682] kjournald starting. Commit interval 5 seconds [ 3.499542] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.723602] mmci-omap mmci-omap.0: command timeout (CMD1) [ 3.730560] EXT3-fs (mmcblk0p1): using internal journal [ 3.761413] EXT3-fs (mmcblk0p1): recovery complete [ 3.766662] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode [ 3.775207] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.782836] Freeing init memory: 156K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#