$ ÿNOLO X-Loader (v1.1.16, Oct 31 2008) Secondary image size 99036 Booting secondary Nokia OMAP Loader v1.1.16 (Oct 31 2008) running on Nokia N800 F5 (RX-34) Clocks: Core: 658 MHz L3: 109 MHz L4: 109 MHz MPU: 329 MHz DSP: 219 MHz IVA: 109 MHz I2C v3.4 Menelaus v2.2 found Vilma v1.5 found Betty v2.1 found Reset reason: pwr_key System DMA v2.0 OneNAND blocks unlocked in 30264 us Flash id: ec4811 Partition table successfully read McSPI v1.4 RFBI version 1.0 Detecting LCD panel lph8923 Panel ID: 838f48 URAL panel detected Detected LCD panel: ls041y3 S1D13745 Hailstorm detected FB memory blanking took 242 ms (3089 kB/s) Logo drawn in 24 ms (1218 kB/s) Über-cool backlight fade-in took 101 ms Prompt keypress detected Initializing USB No USB host detected nolo> usb Initializing USB Entering USB loop SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 64 bytes) SETUP: WR STD DEVICE SET_ADDRESS value 002e index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 18 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 9 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 94 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 00, index 0000, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 02, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 01, index 0409, length 255 bytes) SETUP: WR STD DEVICE SET_CONFIGURATION value 0001 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 03, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0001 index 0002 length 0000 Flashing interface selected SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 Flashing mode entered SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 SETUP: RD VND DEVICE req 04 value 0000 index 0000 length 0200 SETUP: RD VND DEVICE req 03 value 0000 index 0000 length 0004 SETUP: WR VND DEVICE req 12 value 0000 index 0000 length 0012 SETUP: RD VND DEVICE req 14 value 0000 index 0000 length 0200 SETUP: WR VND DEVICE req 42 value 0000 index 0000 length 001b Receiving kernel (length 1985536) Image successfully received SETUP: WR VND DEVICE req 82 value 0000 index 0000 length 0000 SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 Boot requested Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.5.0-rc4-00005-gdde3d97 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Tue Jun 26 19:42:58 MDT 2012 [ 0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Nokia N800 [ 0.000000] Ignoring unrecognised tag 0x414f4d50 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c03f3120, node_mem_map c091b000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] OMAP2420 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttyO2,115200 earlyprintk debug init=/bin/bash [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 120572k/120572k available, 10500k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0387504 (3582 kB) [ 0.000000] .init : 0xc0388000 - 0xc03af000 ( 156 kB) [ 0.000000] .data : 0xc03b0000 - 0xc03f3b80 ( 271 kB) [ 0.000000] .bss : 0xc03f3ba4 - 0xc091a1c8 (5274 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] NR_IRQS:474 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.110931] Calibrating delay loop... 325.10 BogoMIPS (lpj=1271808) [ 0.117553] pid_max: default: 32768 minimum: 301 [ 0.123291] Security Framework initialized [ 0.128051] Mount-cache hash table entries: 512 [ 0.143432] CPU: Testing write buffer coherency: ok [ 0.149993] hw perfevents: enabled with v6 PMU driver, 3 counters available [ 0.157745] Setting up static identity map for 0x80280270 - 0x802802cc [ 0.182373] ttyO2 used as console in debug mode uart2 clocks will not be gated [ 0.182403] omap_hwmod: rng: cannot be enabled for reset (3) [ 0.213378] dummy: [ 0.218627] GPMC revision 2.0 [ 0.222473] gpmc: irq-20 could not claim: err -22 [ 0.246765] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.254455] OMAP GPIO hardware version 1.8 [ 0.261657] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.271942] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.282043] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.303985] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.369293] mmci-omap.0: alias fck already exists [ 0.376007] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.385192] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.394317] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.403442] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.412567] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.421691] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.430786] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.437957] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.478363] OMAP DMA hardware revision 2.0 [ 0.568176] bio: create slab at 0 [ 0.590911] SCSI subsystem initialized [ 0.599426] omap_i2c omap_i2c.1: bus 1 rev1.3.4 at 400 kHz [ 0.612945] omap_i2c omap_i2c.2: bus 2 rev1.3.4 at 400 kHz [ 0.630249] Switching to clocksource 32k_counter [ 0.777099] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.814849] VFS: Disk quotas dquot_6.5.2 [ 0.819396] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.829406] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.839294] msgmni has been set to 235 [ 0.852447] io scheduler noop registered [ 0.856811] io scheduler deadline registered [ 0.861602] io scheduler cfq registered (default) [ 0.877471] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.902008] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 0.914001] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 0.925018] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 74) is a OMAP UART2 [ 0.933197] console [ttyO2] enabled, bootconsole disabled [ 0.933197] console [ttyO2] enabled, bootconsole disabled [ 0.955535] omap_rng omap_rng: OMAP Random Number Generator ver. 40 [ 1.038330] brd: module loaded [ 1.085937] loop: module loaded [ 1.093078] Menelaus rev 2.2 [ 1.125976] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.135314] OneNAND driver initializing [ 1.141296] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c8880000, freq 54 MHz [ 1.152801] OneNAND Manufacturer: Samsung (0xec) [ 1.157684] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48) [ 1.163299] OneNAND version = 0x0011 [ 1.167144] Chip support all block unlock [ 1.171508] onenand_wait: controller error! state 15 ctrl 0x0440 intr 0x8000 [ 1.180633] Scanning device for bad blocks [ 1.193115] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x39 addr8 0x0 [ 1.201507] OneNAND eraseblock 57 is an initial bad block [ 1.207366] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3a addr8 0x0 [ 1.215728] OneNAND eraseblock 58 is an initial bad block [ 1.221588] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3b addr8 0x0 [ 1.229919] OneNAND eraseblock 59 is an initial bad block [ 1.248870] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xa7 addr8 0x0 [ 1.257232] OneNAND eraseblock 167 is an initial bad block [ 1.264739] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xb5 addr8 0x0 [ 1.273101] OneNAND eraseblock 181 is an initial bad block [ 1.311889] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x1c9 addr8 0x0 [ 1.320343] OneNAND eraseblock 457 is an initial bad block [ 1.518615] Creating 5 MTD partitions on "omap2-onenand": [ 1.524353] 0x000000000000-0x000000020000 : "bootloader" [ 1.545776] 0x000000020000-0x000000080000 : "config" [ 1.561920] 0x000000080000-0x000000280000 : "kernel" [ 1.578430] 0x000000280000-0x000000680000 : "initfs" [ 1.594665] 0x000000680000-0x000010000000 : "rootfs" [ 1.654815] mousedev: PS/2 mouse device common for all mice [ 1.672821] i2c /dev entries driver [ 1.684234] Driver for 1-wire Dallas network protocol. [ 1.697418] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec [ 1.817962] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.825469] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.849487] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.856109] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.862670] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.869171] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.897064] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 1.905639] mux: Failed to setup hwmod io irq -22 [ 1.923278] Power Management for OMAP2 initializing [ 1.928588] PRCM revision 1.0 [ 1.969512] clock: disabling unused clocks to save power [ 1.987487] /home/paul/linux/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.004913] Waiting for root device /dev/mmcblk0p1... [ 2.786651] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.795837] mmc0: new SDHC card at address 1234 [ 2.806518] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 2.825317] mmcblk0: p1 [ 2.836456] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.843200] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.853790] mmci-omap mmci-omap.0: command timeout (CMD8) [ 2.860382] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.866973] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.873535] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.880065] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.893432] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.900207] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.909301] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.918457] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.931030] mmci-omap mmci-omap.0: command timeout (CMD1) [ 4.820281] kjournald starting. Commit interval 5 seconds [ 4.837005] EXT3-fs (mmcblk0p1): using internal journal [ 4.854949] EXT3-fs (mmcblk0p1): recovery complete [ 4.860046] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode [ 4.868438] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.876068] Freeing init memory: 156K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/# root@(none):/# root@(none):/# mount -t sysfs none /sys root@(none):/# cat /sys/class/misc/hw_random/rng_available omap root@(none):/# cat /sys/class/misc/hw_random/rng_current omap root@(none):/# mknod /dev/hw_random c 10 183 mknod: `/dev/hw_random': File exists root@(none):/# dd if=/dev/hw_random of=/tmp/foo bs=1024 count=1024 1024+0 records in 1024+0 records out 1048576 bytes (1.0 MB) copied, 2.49289 s, 421 kB/s root@(none):/# gzip /tmp/foo root@(none):/# ls -l /tmp/foo.gz -rw-r--r-- 1 root root 1048758 Jan 1 00:00 /tmp/foo.gz root@(none):/#