Texas Instruments X-Loader 1.47 (Jan 14 2011 - 15:43:28) Starting X-loader on MMC Reading boot sector 212836 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... U-Boot 2010.06 (Jan 14 2011 - 15:43:45) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 EVM board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB In: serial Out: serial Err: serial Read back SMSC id 0x92200000 Die ID #368000229ff80000016071640902c013 Net: smc911x-0 Hit any key to stop autoboot: 3  2  1  0 smc911x: detected LAN9220 controller smc911x: phy initialized smc911x: MAC 00:50:c2:7e:99:42 BOOTP broadcast 1 DHCP client bound to address 192.168.57.131 Using smc911x-0 device TFTP from server 192.168.57.1; our IP address is 192.168.57.131 Filename 'uImage.37xevm'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################## done Bytes transferred = 4163960 (3f8978 hex) ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.7.0-rc2-00166-gb4d8b16 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4163896 Bytes = 4 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.7.0-rc2-00166-gb4d8b16 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Mon Nov 12 19:25:19 MST 2012 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP3 EVM [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0f4f000 s12928 r8192 d15744 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 245204k/245204k available, 16940k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc070b814 (7183 kB) [ 0.000000] .init : 0xc070c000 - 0xc075c280 ( 321 kB) [ 0.000000] .data : 0xc075e000 - 0xc07edaa0 ( 575 kB) [ 0.000000] .bss : 0xc07edac4 - 0xc0d484ec (5483 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.001037] Calibrating delay loop... 397.57 BogoMIPS (lpj=1554432) [ 0.109374] pid_max: default: 32768 minimum: 301 [ 0.109985] Security Framework initialized [ 0.110168] Mount-cache hash table entries: 512 [ 0.114807] CPU: Testing write buffer coherency: ok [ 0.115692] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.115753] Setting up static identity map for 0x8051fed8 - 0x8051ff48 [ 0.118530] Brought up 1 CPUs [ 0.118560] SMP: Total of 1 processors activated (397.57 BogoMIPS). [ 0.137115] pinctrl core: initialized pinctrl subsystem [ 0.143646] regulator-dummy: no parameters [ 0.145782] NET: Registered protocol family 16 [ 0.146575] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.148620] omap-gpmc omap-gpmc: GPMC revision 5.0 [ 0.161376] OMAP GPIO hardware version 2.5 [ 0.181762] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.197418] _omap_mux_get_by_name: Could not find signal uart4_rx.uart4_rx [ 0.206024] Reprogramming SDRC clock to 400000000 Hz [ 0.209075] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.224761] omap-mcbsp.2: alias fck already exists [ 0.225646] omap-mcbsp.3: alias fck already exists [ 0.229949] OMAP DMA hardware revision 5.0 [ 0.235778] arm-pmu: alias fck already exists [ 0.306274] bio: create slab at 0 [ 0.404479] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.405609] fixed-dummy: no parameters [ 0.411834] SCSI subsystem initialized [ 0.415405] usbcore: registered new interface driver usbfs [ 0.416046] usbcore: registered new interface driver hub [ 0.416931] usbcore: registered new device driver usb [ 0.443267] twl 1-0048: PIH (irq 23) chaining IRQs 338..346 [ 0.443969] twl 1-0048: power (irq 343) chaining IRQs 346..353 [ 0.447296] twl4030_gpio twl4030_gpio: gpio (irq 338) chaining IRQs 354..371 [ 0.460418] VIO: 1800 mV normal standby [ 0.463439] vdd_mpu_iva: 600 <--> 1450 mV normal [ 0.465759] vdd_core: 600 <--> 1450 mV normal [ 0.468292] VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby [ 0.471771] VDAC: 1800 mV normal standby [ 0.474914] VAUX2_4030: 2800 mV normal standby [ 0.478393] VPLL2: 1800 mV normal standby [ 0.481231] VSIM: 1800 <--> 3000 mV at 1800 mV normal standby [ 0.482177] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz [ 0.493682] omap_i2c omap_i2c.2: bus 2 rev1.4.0 at 400 kHz [ 0.509094] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 400 kHz [ 0.517364] Switching to clocksource 32k_counter [ 0.656158] NET: Registered protocol family 2 [ 0.658264] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.658935] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.663452] TCP: Hash tables configured (established 8192 bind 8192) [ 0.663696] TCP: reno registered [ 0.663726] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.664062] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.665039] NET: Registered protocol family 1 [ 0.666809] RPC: Registered named UNIX socket transport module. [ 0.666839] RPC: Registered udp transport module. [ 0.666870] RPC: Registered tcp transport module. [ 0.666870] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.668029] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.668395] CPU PMU: probing PMU on CPU 0 [ 0.668579] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.855499] VFS: Disk quotas dquot_6.5.2 [ 0.855804] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.858734] NFS: Registering the id_resolver key type [ 0.859252] Key type id_resolver registered [ 0.859283] Key type id_legacy registered [ 0.859436] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.860076] msgmni has been set to 478 [ 0.864013] io scheduler noop registered [ 0.864044] io scheduler deadline registered [ 0.864135] io scheduler cfq registered (default) [ 0.868774] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.876403] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0 [ 1.557525] console [ttyO0] enabled [ 1.563385] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1 [ 1.572845] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 90) is a OMAP UART2 [ 1.581878] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 96) is a OMAP UART3 [ 1.626403] brd: module loaded [ 1.651123] loop: module loaded [ 1.662567] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.670318] NAND device: Manufacturer ID: 0xad, Chip ID: 0xbc (Hynix NAND 512MiB 1,8V 16-bit), page size: 2048, OOB size: 64 [ 1.682250] Creating 5 MTD partitions on "omap2-nand.0": [ 1.687866] 0x000000000000-0x000000080000 : "X-Loader" [ 1.700866] 0x000000080000-0x000000240000 : "U-Boot" [ 1.712341] 0x000000240000-0x000000280000 : "U-Boot Env" [ 1.723510] 0x000000280000-0x000000780000 : "Kernel" [ 1.738037] 0x000000780000-0x000020000000 : "File system" [ 2.189483] OneNAND driver initializing [ 2.196655] omap-dma-engine omap-dma-engine: allocating channel for 36 [ 2.203704] omap-dma-engine omap-dma-engine: allocating channel for 35 [ 2.221252] smsc911x: Driver version 2008-10-21 [ 2.234558] libphy: smsc911x-mdio: probed [ 2.239135] smsc911x smsc911x.0 eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=smsc911x-0:01, irq=-1) [ 2.250274] smsc911x smsc911x.0 eth0: MAC Address: 00:50:c2:7e:99:42 [ 2.258361] usbcore: registered new interface driver asix [ 2.264709] usbcore: registered new interface driver cdc_ether [ 2.271514] usbcore: registered new interface driver smsc95xx [ 2.278167] usbcore: registered new interface driver net1080 [ 2.284729] usbcore: registered new interface driver cdc_subset [ 2.291564] usbcore: registered new interface driver zaurus [ 2.298034] usbcore: registered new interface driver cdc_ncm [ 2.306365] usbcore: registered new interface driver cdc_wdm [ 2.312408] Initializing USB Mass Storage driver... [ 2.318206] usbcore: registered new interface driver usb-storage [ 2.324615] USB Mass Storage support registered. [ 2.330078] usbcore: registered new interface driver usbtest [ 2.337982] mousedev: PS/2 mouse device common for all mice [ 2.346618] input: TWL4030 Keypad as /devices/platform/omap_i2c.1/i2c-1/1-004a/twl4030_keypad/input/input0 [ 2.364898] ads7846 spi1.0: touchscreen, irq 289 [ 2.372406] input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.1/spi_master/spi1/spi1.0/input/input1 [ 2.389312] input: twl4030_pwrbutton as /devices/platform/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input2 [ 2.402374] twl_rtc twl_rtc: Power up reset detected. [ 2.407867] twl_rtc twl_rtc: Enabling TWL-RTC [ 2.417510] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 2.425659] i2c /dev entries driver [ 2.433563] Driver for 1-wire Dallas network protocol. [ 2.442596] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.451263] twl4030_wdt twl4030_wdt: Failed to register misc device [ 2.458099] twl4030_wdt: probe of twl4030_wdt failed with error -16 [ 2.468780] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk [ 2.475311] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 2.482269] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 2.869873] usbcore: registered new interface driver usbhid [ 2.875793] usbhid: USB HID core driver [ 2.881744] oprofile: using arm/armv7 [ 2.886505] TCP: cubic registered [ 2.890014] Initializing XFRM netlink socket [ 2.894714] NET: Registered protocol family 17 [ 2.899505] NET: Registered protocol family 15 [ 2.904754] Key type dns_resolver registered [ 2.909484] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.929046] ThumbEE CPU extension supported. [ 2.946289] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.958160] smsc911x smsc911x.0 eth0: SMSC911x/921x identified at 0xd085a000, IRQ: 290 [ 2.987030] Sending DHCP requests .[ 3.117645] mmc0: new SDHC card at address e624 [ 3.125671] mmcblk0: mmc0:e624 SD08G 7.40 GiB [ 3.147094] mmcblk0: p1 p2 p3 ., OK [ 5.792053] IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.57.131 [ 5.800476] IP-Config: Complete: [ 5.803863] device=eth0, addr=192.168.57.131, mask=255.255.255.0, gw=255.255.255.255 [ 5.812591] host=192.168.57.131, domain=example.org, nis-domain=(none) [ 5.819976] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.826782] nameserver0=192.168.57.1[ 5.853454] VFS: Mounted root (nfs filesystem) on device 0:11. [ 5.860382] Freeing init memory: 320K /bin/sh: 0: can't access tty; job control turned off # %% Start PM consolidated quick test %% Preparation # # mount -t sysfs none /sys # # mount -t debugfs none /debug # # # # echo -1 > /sys/devices/platform/omap_uart.0/power/autosuspend_delay_ms # # echo -1 > /sys/devices/platform/omap_uart.1/power/autosuspend_delay_ms # # echo -1 > /sys/devices/platform/omap_uart.2/power/autosuspend_delay_ms # # echo -1 > /sys/devices/platform/omap_uart.3/power/autosuspend_delay_ms # # echo 0 > /debug/pm_debug/enable_off_mode # # %% Baseline pm_debug count dump cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:605,INA:0,ON:606,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:605,INA:0,ON:606,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:0,RET:605,INA:0,ON:606,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:605,INA:0,ON:606,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:605,INA:0,ON:606,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (2) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (2626) cam_clkdm->cam_pwrdm (1) dss_clkdm->dss_pwrdm (9) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (53) core_l3_clkdm->core_pwrdm (2) neon_clkdm->neon_pwrdm (0) # # echo enabled > /sys/devices/platform/omap_uart.2/tty/ttyO2/power/wakeup # %% Start retention double suspend/resume UART wakeup test # echo mem > /sys/power/state [ 16.355743] PM: Syncing filesystems ... done. [ 16.372222] Freezing user space processes ... (elapsed 0.00 seconds) done. [ 16.379791] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done. [ 16.411834] Suspending console(s) (use no_console_suspend to debug) [ 16.549224] PM: suspend of devices complete after 125.305 msecs [ 16.553649] PM: late suspend of devices complete after 4.425 msecs [ 16.560089] PM: noirq suspend of devices complete after 6.378 msecs [ 16.560150] Disabling non-boot CPUs ... [ 16.560546] Successfully put all powerdomains to target state [ 16.564147] PM: noirq resume of devices complete after 3.387 msecs [ 16.568359] PM: early resume of devices complete after 2.868 msecs [ 16.902343] PM: resume of devices complete after 333.892 msecs [ 16.958038] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:705,INA:0,ON:706,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:705,INA:0,ON:706,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:0,RET:705,INA:0,ON:706,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:705,INA:0,ON:706,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:705,INA:0,ON:706,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (2) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (3040) cam_clkdm->cam_pwrdm (1) dss_clkdm->dss_pwrdm (9) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (64) core_l3_clkdm->core_pwrdm (2) neon_clkdm->neon_pwrdm (0) # # # # echo mem > /sys/power/state [ 19.765380] PM: Syncing filesystems ... done. [ 19.772827] Freezing user space processes ... (elapsed 0.00 seconds) done. [ 19.780364] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done. [ 19.810394] Suspending console(s) (use no_console_suspend to debug) [ 19.947204] PM: suspend of devices complete after 124.816 msecs [ 19.951629] PM: late suspend of devices complete after 4.425 msecs [ 19.957702] PM: noirq suspend of devices complete after 6.042 msecs [ 19.957702] Disabling non-boot CPUs ... [ 19.958007] Successfully put all powerdomains to target state [ 19.961547] PM: noirq resume of devices complete after 3.356 msecs [ 19.965698] PM: early resume of devices complete after 2.960 msecs [ 20.299743] PM: resume of devices complete after 333.923 msecs [ 20.355285] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:797,INA:0,ON:798,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:797,INA:0,ON:798,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:0,RET:797,INA:0,ON:798,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:797,INA:0,ON:798,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:797,INA:0,ON:798,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (2) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (3422) cam_clkdm->cam_pwrdm (1) dss_clkdm->dss_pwrdm (9) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (75) core_l3_clkdm->core_pwrdm (2) neon_clkdm->neon_pwrdm (0) # # # # ./test_rootfs_access_nonexistent_file__ret_susp /bin/sh: 39: ./test_rootfs_access_nonexistent_file__ret_susp: not found # # %% End retention double suspend/resume UART wakeup test %% Start retention dynamic idle UART wakeup test echo 3000 > /sys/devices/platform/omap_uart.0/power/autosuspend_delay_ms # # echo 3000 > /sys/devices/platform/omap_uart.1/power/autosuspend_delay_ms # # echo 3000 > /sys/devices/platform/omap_uart.2/power/autosuspend_delay_ms # # echo 3000 > /sys/devices/platform/omap_uart.3/power/autosuspend_delay_ms # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:924,INA:0,ON:925,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:6,INA:0,ON:7,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:23,INA:0,ON:24,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:924,INA:0,ON:925,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:0,RET:924,INA:0,ON:925,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:924,INA:0,ON:925,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:924,INA:0,ON:925,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (2) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (3946) cam_clkdm->cam_pwrdm (1) dss_clkdm->dss_pwrdm (9) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (77) core_l3_clkdm->core_pwrdm (2) neon_clkdm->neon_pwrdm (0) # # # # ./test_rootfs_access_nonexistent_file__ret_dyn /bin/sh: 55: ./test_rootfs_access_nonexistent_file__ret_dyn: not found # # echo -1 > /sys/devices/platform/omap_uart.0/power/autosuspend_delay_ms # # echo -1 > /sys/devices/platform/omap_uart.1/power/autosuspend_delay_ms # # echo -1 > /sys/devices/platform/omap_uart.2/power/autosuspend_delay_ms # # echo -1 > /sys/devices/platform/omap_uart.3/power/autosuspend_delay_ms # # %% End retention dynamic idle UART wakeup test %% Start off-mode double suspend UART wakeup test echo 1 > /debug/pm_debug/enable_off_mode # # echo mem > /sys/power/state [ 42.961425] PM: Syncing filesystems ... done. [ 42.969207] Freezing user space processes ... (elapsed 0.00 seconds) done. [ 42.976745] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done. [ 43.006378] Suspending console(s) (use no_console_suspend to debug) [ 43.142730] PM: suspend of devices complete after 124.298 msecs [ 43.147125] PM: late suspend of devices complete after 4.394 msecs [ 43.153198] PM: noirq suspend of devices complete after 6.011 msecs [ 43.153198] Disabling non-boot CPUs ... [ 43.153503] Successfully put all powerdomains to target state [ 43.157470] PM: noirq resume of devices complete after 3.662 msecs [ 43.161651] PM: early resume of devices complete after 2.960 msecs [ 43.495666] PM: resume of devices complete after 333.923 msecs [ 43.551269] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:28,RET:1039,INA:0,ON:1068,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:1,RET:6,INA:0,ON:8,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:1,RET:124,INA:0,ON:126,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:28,RET:1039,INA:0,ON:1068,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:28,RET:1039,INA:0,ON:1068,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:28,RET:1039,INA:0,ON:1068,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:28,RET:1039,INA:0,ON:1068,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (2) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (4550) cam_clkdm->cam_pwrdm (1) dss_clkdm->dss_pwrdm (9) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (89) core_l3_clkdm->core_pwrdm (2) neon_clkdm->neon_pwrdm (0) # # # # echo mem > /sys/power/state [ 50.826934] PM: Syncing filesystems ... done. [ 50.834686] Freezing user space processes ... (elapsed 0.00 seconds) done. [ 50.842193] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done. [ 50.873687] Suspending console(s) (use no_console_suspend to debug) [ 51.010070] PM: suspend of devices complete after 124.298 msecs [ 51.014526] PM: late suspend of devices complete after 4.425 msecs [ 51.020538] PM: noirq suspend of devices complete after 6.011 msecs [ 51.020568] Disabling non-boot CPUs ... [ 51.020843] Successfully put all powerdomains to target state [ 51.024780] PM: noirq resume of devices complete after 3.662 msecs [ 51.028930] PM: early resume of devices complete after 2.960 msecs [ 51.362792] PM: resume of devices complete after 333.740 msecs [ 51.418334] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:112,RET:1039,INA:0,ON:1152,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:2,RET:6,INA:0,ON:9,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:2,RET:124,INA:0,ON:127,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:112,RET:1039,INA:0,ON:1152,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:112,RET:1039,INA:0,ON:1152,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:112,RET:1039,INA:0,ON:1152,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:112,RET:1039,INA:0,ON:1152,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (2) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (4924) cam_clkdm->cam_pwrdm (1) dss_clkdm->dss_pwrdm (9) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (100) core_l3_clkdm->core_pwrdm (2) neon_clkdm->neon_pwrdm (0) # # # # ./test_rootfs_access_nonexistent_file__off_susp /bin/sh: 83: ./test_rootfs_access_nonexistent_file__off_susp: not found # # %% End off-mode double suspend UART wakeup test %% Start off-mode dynamic idle UART wakeup test echo 3000 > /sys/devices/platform/omap_uart.0/power/autosuspend_delay_ms # # echo 3000 > /sys/devices/platform/omap_uart.1/power/autosuspend_delay_ms # # echo 3000 > /sys/devices/platform/omap_uart.2/power/autosuspend_delay_ms # # echo 3000 > /sys/devices/platform/omap_uart.3/power/autosuspend_delay_ms # # # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:1240,RET:1039,INA:0,ON:2280,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:2,RET:6,INA:0,ON:9,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:1030,RET:124,INA:0,ON:1155,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:1240,RET:1039,INA:0,ON:2280,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (ON),OFF:1240,RET:1039,INA:0,ON:2280,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:1240,RET:1039,INA:0,ON:2280,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:1240,RET:1039,INA:0,ON:2280,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (2) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (9468) cam_clkdm->cam_pwrdm (1) dss_clkdm->dss_pwrdm (9) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (103) core_l3_clkdm->core_pwrdm (2) neon_clkdm->neon_pwrdm (0) # # # # ./test_rootfs_access_nonexistent_file__off_dyn /bin/sh: 101: ./test_rootfs_access_nonexistent_file__off_dyn: not found # # %% End off-mode dynamic idle UART wakeup test %% End PM consolidated quick test