NOLO X-Loader (v1.1.16, Oct 31 2008) Secondary image size 99036 Booting secondary Nokia OMAP Loader v1.1.16 (Oct 31 2008) running on Nokia N800 F5 (RX-34) Clocks: Core: 658 MHz L3: 109 MHz L4: 109 MHz MPU: 329 MHz DSP: 219 MHz IVA: 109 MHz I2C v3.4 Menelaus v2.2 found Vilma v1.5 found Betty v2.1 found Reset reason: pwr_key System DMA v2.0 OneNAND blocks unlocked in 30264 us Flash id: ec4811 Partition table successfully read McSPI v1.4 RFBI version 1.0 Detecting LCD panel lph8923 Panel ID: 838f48 URAL panel detected Detected LCD panel: ls041y3 S1D13745 Hailstorm detected FB memory blanking took 242 ms (3089 kB/s) Logo drawn in 24 ms (1218 kB/s) Über-cool backlight fade-in took 101 ms Initializing USB USB host detected Entering USB loop SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 64 bytes) SETUP: WR STD DEVICE SET_ADDRESS value 0009 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 18 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 9 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 94 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 00, index 0000, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 02, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 01, index 0409, length 255 bytes) SETUP: WR STD DEVICE SET_CONFIGURATION value 0001 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 03, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0001 index 0002 length 0000 Flashing interface selected SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 Flashing mode entered SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 SETUP: RD VND DEVICE req 04 value 0000 index 0000 length 0200 SETUP: RD VND DEVICE req 03 value 0000 index 0000 length 0004 SETUP: WR VND DEVICE req 12 value 0000 index 0000 length 0012 SETUP: RD VND DEVICE req 14 value 0000 index 0000 length 0200 SETUP: WR VND DEVICE req 42 value 0000 index 0000 length 001b Receiving kernel (length 2061184) Image successfully received SETUP: WR VND DEVICE req 82 value 0000 index 0000 length 0000 SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 Boot requested Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.7.0-rc3-00559-g4cadc5b (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Tue Oct 30 19:03:51 MDT 2012 [ 0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Nokia N800 [ 0.000000] Ignoring unrecognised tag 0x414f4d50 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c0404c60, node_mem_map c092d000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] OMAP2420 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttyO2,115200 earlyprintk debug init=/bin/bash [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 120500k/120500k available, 10572k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc03ad164 (3733 kB) [ 0.000000] .init : 0xc03ae000 - 0xc03d4aec ( 155 kB) [ 0.000000] .data : 0xc03d6000 - 0xc0405e20 ( 192 kB) [ 0.000000] .bss : 0xc0405e44 - 0xc092cf8c (5277 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.063842] Calibrating delay loop... 218.45 BogoMIPS (lpj=851968) [ 0.121673] pid_max: default: 32768 minimum: 301 [ 0.127380] Security Framework initialized [ 0.131958] Mount-cache hash table entries: 512 [ 0.146850] CPU: Testing write buffer coherency: ok [ 0.154327] Setting up static identity map for 0x8029a018 - 0x8029a074 [ 0.176452] ttyO2 used as console in debug mode: uart2 clocks will not be gated [ 0.218963] pinctrl core: initialized pinctrl subsystem [ 0.242187] regulator-dummy: no parameters [ 0.250457] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.260589] omap-gpmc omap-gpmc: GPMC revision 2.0 [ 0.285522] omap_gpio omap_gpio.0: Could not get gpio dbck [ 0.295257] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.303009] OMAP GPIO hardware version 1.8 [ 0.309997] omap_gpio omap_gpio.1: Could not get gpio dbck [ 0.318206] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.328338] omap_gpio omap_gpio.2: Could not get gpio dbck [ 0.337280] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.347747] omap_gpio omap_gpio.3: Could not get gpio dbck [ 0.355590] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.378265] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.443786] mmci-omap.0: alias fck already exists [ 0.450683] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.459899] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.469024] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.478118] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.487243] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.496368] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.505493] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.512634] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.553283] OMAP DMA hardware revision 2.0 [ 0.650238] bio: create slab at 0 [ 0.672973] SCSI subsystem initialized [ 0.690338] omap_i2c omap_i2c.1: bus 1 rev1.3.4 at 400 kHz [ 0.708038] omap_i2c omap_i2c.2: bus 2 rev1.3.4 at 400 kHz [ 0.723815] Switching to clocksource 32k_counter [ 0.876556] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.884094] CPU PMU: probing PMU on CPU 0 [ 0.888488] hw perfevents: enabled with v6 PMU driver, 3 counters available [ 0.924530] VFS: Disk quotas dquot_6.5.2 [ 0.928863] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.938842] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.948150] msgmni has been set to 235 [ 0.961608] io scheduler noop registered [ 0.965972] io scheduler deadline registered [ 0.970642] io scheduler cfq registered (default) [ 0.986724] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.011596] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0 [ 1.024505] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1 [ 1.036285] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 90) is a OMAP UART2 [ 1.044433] console [ttyO2] enabled, bootconsole disabled [ 1.044433] console [ttyO2] enabled, bootconsole disabled [ 1.066314] omap_rng omap_rng: OMAP Random Number Generator ver. 40 [ 1.151580] brd: module loaded [ 1.200439] loop: module loaded [ 1.207916] Menelaus rev 2.2 [ 1.243225] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.252960] OneNAND driver initializing [ 1.258636] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c88c0000, freq 54 MHz [ 1.270141] OneNAND Manufacturer: Samsung (0xec) [ 1.275054] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48) [ 1.280670] OneNAND version = 0x0011 [ 1.284545] Chip support all block unlock [ 1.288909] onenand_wait: controller error! state 15 ctrl 0x0440 intr 0x8000 [ 1.298095] Scanning device for bad blocks [ 1.310913] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x39 addr8 0x0 [ 1.319335] OneNAND eraseblock 57 is an initial bad block [ 1.325225] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3a addr8 0x0 [ 1.333618] OneNAND eraseblock 58 is an initial bad block [ 1.339477] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3b addr8 0x0 [ 1.347869] OneNAND eraseblock 59 is an initial bad block [ 1.366638] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xa7 addr8 0x0 [ 1.374999] OneNAND eraseblock 167 is an initial bad block [ 1.382537] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xb5 addr8 0x0 [ 1.390899] OneNAND eraseblock 181 is an initial bad block [ 1.430084] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x1c9 addr8 0x0 [ 1.438568] OneNAND eraseblock 457 is an initial bad block [ 1.639007] Creating 5 MTD partitions on "omap2-onenand": [ 1.644836] 0x000000000000-0x000000020000 : "bootloader" [ 1.666900] 0x000000020000-0x000000080000 : "config" [ 1.683074] 0x000000080000-0x000000280000 : "kernel" [ 1.699768] 0x000000280000-0x000000680000 : "initfs" [ 1.716125] 0x000000680000-0x000010000000 : "rootfs" [ 1.764251] spi spi2.0: no RX DMA engine channel for McSPI [ 1.770294] omap2_mcspi omap2_mcspi.2: can't setup spi2.0, status -11 [ 1.777374] omap2_mcspi omap2_mcspi.2: can't create new device for p54spi [ 1.791107] mousedev: PS/2 mouse device common for all mice [ 1.809631] i2c /dev entries driver [ 1.820892] Driver for 1-wire Dallas network protocol. [ 1.834594] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec [ 1.848510] mmci-omap mmci-omap.0: unable to obtain TX DMA engine channel 61 [ 1.856170] mmci-omap mmci-omap.0: unable to obtain RX DMA engine channel 62 [ 1.966369] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.973907] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.997833] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.005981] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.012603] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.021179] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.048522] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 2.057312] mux: Failed to setup hwmod io irq -22 [ 2.074890] Power Management for OMAP2 initializing [ 2.080078] PRCM revision 1.0 [ 2.120422] clock: disabling unused clocks to save power [ 2.142639] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.158508] Waiting for root device /dev/mmcblk0p1... [ 2.411254] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.420501] mmc0: new SDHC card at address 1234 [ 2.431152] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 2.449584] mmcblk0: p1 [ 2.460968] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.467773] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.478515] mmci-omap mmci-omap.0: command timeout (CMD8) [ 2.485168] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.496398] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.504638] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.514587] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.521606] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.532348] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.542816] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.550750] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.563171] mmci-omap mmci-omap.0: command timeout (CMD1) [ 2.868743] kjournald starting. Commit interval 5 seconds [ 3.099609] EXT3-fs (mmcblk0p1): using internal journal [ 3.118438] EXT3-fs (mmcblk0p1): recovery complete [ 3.123718] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode [ 3.132080] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 3.139709] Freeing init memory: 152K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#