怘€ć€˜€`3f<€fŔćřŔ̆ž?`??f?ćžf<řž`??đ3ž<3ž<`<f<?˜ŕ?̘ŕ0˜˜fĂđŔ€˜ŕĂŔ˜ŕŔ˜ž˜ŕ˜x~ó˜x~đŕ˜˜˜03ŕ3`?<?`?†žřž~<˜˜33žţž`?ŕžţž<`<f<?†řćžćž˜33€ć†ť`0???˜03ŕ

U-Boot 2012.07-00136-g755de79 (Aug 24 2012 - 14:19:44)

CPU  : OMAP4430 ES2.0
Board: OMAP4 Panda
I2C:   ready
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  3  0 
Panda # 
Panda # loady
## Ready for binary (ymodem) download to 0x82000000 at 230400 bps...
CSending: uImage
Sending: 

Transfer complete
xyzModem - CRC mode, 6(SOH)/4070(STX)/0(CAN) packets, 3 retries
## Total Size      = 0x003f99f0 = 4168176 Bytes
Panda # 
Panda # 
Panda # setenv bootargs console=ttyO2,230400n8 vram=16M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait earlyprintk
Panda # 
Panda # bootm
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.7.0-rc4-01279-gee05754
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4168112 Bytes = 4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Linux version 3.7.0-rc4-01279-gee05754 (paul@knihy) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Wed Nov 21 16:54:06 MST 2012
[    0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: OMAP4 Panda board
[    0.000000] Reserving 16777216 bytes SDRAM for VRAM
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] OMAP4430 ES2.0
[    0.000000] PERCPU: Embedded 9 pages/cpu @c1153000 s12928 r8192 d15744 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125696
[    0.000000] Kernel command line: console=ttyO2,230400n8 vram=16M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait earlyprintk
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 495MB = 495MB total
[    0.000000] Memory: 488668k/488668k available, 35620k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc070c88c   (7187 kB)
[    0.000000]       .init : 0xc070d000 - 0xc075e280   ( 325 kB)
[    0.000000]       .data : 0xc0760000 - 0xc07f0100   ( 577 kB)
[    0.000000]        .bss : 0xc07f0124 - 0xc0d4aaec   (5483 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[    0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.000000] ... MAX_LOCK_DEPTH:          48
[    0.000000] ... MAX_LOCKDEP_KEYS:        8191
[    0.000000] ... CLASSHASH_SIZE:          4096
[    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
[    0.000000] ... CHAINHASH_SIZE:          16384
[    0.000000]  memory used by lock dependency info: 3695 kB
[    0.000000]  per task-struct memory footprint: 1152 bytes
[    0.001251] Calibrating delay loop... 2007.19 BogoMIPS (lpj=7839744)
[    0.124847] pid_max: default: 32768 minimum: 301
[    0.125671] Security Framework initialized
[    0.125976] Mount-cache hash table entries: 512
[    0.131011] CPU: Testing write buffer coherency: ok
[    0.132324] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.132781] Setting up static identity map for 0x80520b58 - 0x80520bc8
[    0.132873] L310 cache controller enabled
[    0.132904] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B
[    0.136260] CPU1: Booted secondary processor
[    0.203002] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.203338] Brought up 2 CPUs
[    0.203338] SMP: Total of 2 processors activated (4022.78 BogoMIPS).
[    0.220092] omap_hwmod: l3_instr: _wait_target_disable failed
[    0.224395] omap_hwmod: mcpdm: cannot be enabled for reset (3)
[    0.227050] pinctrl core: initialized pinctrl subsystem
[    0.230072] regulator-dummy: no parameters
[    0.231201] NET: Registered protocol family 16
[    0.232696] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.233703] omap-gpmc omap-gpmc: GPMC revision 6.0
[    0.239868] OMAP GPIO hardware version 0.1
[    0.248474] omap_mux_init: Add partition: #1: core, flags: 2
[    0.250030] omap_mux_init: Add partition: #2: wkup, flags: 2
[    0.250183] error setting wl12xx data: -38
[    0.250335] _omap_mux_get_by_name: Could not find signal sys_nirq
[    0.250366] _omap_mux_get_by_name: Could not find signal sys_nirq
[    0.253692] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[    0.253723] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[    0.304077] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.304107] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.312927] OMAP DMA hardware revision 0.0
[    0.315643] ARM PMU: not yet supported on OMAP4430 due to missing CTI driver
[    0.343383] bio: create slab <bio-0> at 0
[    0.385467] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
[    0.386138] vwl1271: 1800 mV 
[    0.388824] SCSI subsystem initialized
[    0.389984] usbcore: registered new interface driver usbfs
[    0.390228] usbcore: registered new interface driver hub
[    0.390624] usbcore: registered new device driver usb
[    0.409240] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[    0.410705] twl 1-0048: PIH (irq 39) chaining IRQs 418..438
[    0.412261] VUSB: 3300 mV normal standby
[    0.413208] vdd_mpu: 500 <--> 1500 mV normal 
[    0.415161] vdd_iva: 500 <--> 1500 mV normal 
[    0.416107] vdd_core: 500 <--> 1500 mV normal 
[    0.417480] V1V8: 1800 mV normal standby
[    0.418395] V2V1: 2100 mV normal standby
[    0.419494] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[    0.420806] VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[    0.423065] VCXIO: 1800 mV normal standby
[    0.423126] VCXIO: supplied by V2V1
[    0.425109] VDAC: 1800 mV normal standby
[    0.425170] VDAC: supplied by V2V1
[    0.426727] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[    0.427978] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[    0.429504] VANA: 2100 mV normal standby
[    0.430419] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
[    0.446289] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
[    0.461730] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[    0.477020] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
[    0.480865] Switching to clocksource 32k_counter
[    0.542114] NET: Registered protocol family 2
[    0.543487] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.543975] TCP bind hash table entries: 16384 (order: 7, 589824 bytes)
[    0.547729] TCP: Hash tables configured (established 16384 bind 16384)
[    0.548034] TCP: reno registered
[    0.548095] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    0.548217] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    0.548889] NET: Registered protocol family 1
[    0.549865] RPC: Registered named UNIX socket transport module.
[    0.549865] RPC: Registered udp transport module.
[    0.549865] RPC: Registered tcp transport module.
[    0.549896] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.550567] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.697753] VFS: Disk quotas dquot_6.5.2
[    0.697906] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.699676] NFS: Registering the id_resolver key type
[    0.700012] Key type id_resolver registered
[    0.700042] Key type id_legacy registered
[    0.700103] jffs2: version 2.2. (NAND) (SUMMARY)  Š 2001-2006 Red Hat, Inc.
[    0.700561] msgmni has been set to 954
[    0.702423] io scheduler noop registered
[    0.702453] io scheduler deadline registered
[    0.702514] io scheduler cfq registered (default)
[    0.704864] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.708343] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[    0.709442] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[    0.710174] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[    1.101898] console [ttyO2] enabled
[    1.104553] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[    1.124023] brd: module loaded
[    1.134674] loop: module loaded
[    1.139221] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.143096] OneNAND driver initializing
[    1.150848] usbcore: registered new interface driver asix
[    1.154083] usbcore: registered new interface driver cdc_ether
[    1.157531] usbcore: registered new interface driver smsc95xx
[    1.160888] usbcore: registered new interface driver net1080
[    1.164215] usbcore: registered new interface driver cdc_subset
[    1.167633] usbcore: registered new interface driver zaurus
[    1.170989] usbcore: registered new interface driver cdc_ncm
[    1.175079] usbcore: registered new interface driver cdc_wdm
[    1.178192] Initializing USB Mass Storage driver...
[    1.181091] usbcore: registered new interface driver usb-storage
[    1.184387] USB Mass Storage support registered.
[    1.187194] usbcore: registered new interface driver usbtest
[    1.191253] mousedev: PS/2 mouse device common for all mice
[    1.196929] twl_rtc twl_rtc: Power up reset detected.
[    1.200469] twl_rtc twl_rtc: Enabling TWL-RTC
[    1.206237] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[    1.210174] i2c /dev entries driver
[    1.214080] Driver for 1-wire Dallas network protocol.
[    1.218811] omap_wdt: OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[    1.224456] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk
[    1.227813] omap-dma-engine omap-dma-engine: allocating channel for 62
[    1.231506] omap-dma-engine omap-dma-engine: allocating channel for 61
[    1.286071] omap_hsmmc omap_hsmmc.4: Failed to get debounce clk
[    1.289337] omap-dma-engine omap-dma-engine: allocating channel for 60
[    1.292907] omap-dma-engine omap-dma-engine: allocating channel for 59
[    1.415588] usbcore: registered new interface driver usbhid
[    1.418731] usbhid: USB HID core driver
[    1.421691] oprofile: no performance counters
[    1.425323] oprofile: using timer interrupt.
[    1.428283] TCP: cubic registered
[    1.430114] Initializing XFRM netlink socket
[    1.432495] NET: Registered protocol family 17
[    1.435089] NET: Registered protocol family 15
[    1.437774] Key type dns_resolver registered
[    1.440216] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[    1.450531] Power Management for TI OMAP4.
[    1.452941] ThumbEE CPU extension supported.
[    1.460662] VANA: incomplete constraints, leaving on
[    1.464630] VDAC: incomplete constraints, leaving on
[    1.468139] VUSB: incomplete constraints, leaving on
[    1.475097] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    1.482513] Waiting for root device /dev/mmcblk0p2...
[    1.598083] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.602600] mmc0: new SD card at address aaaa
[    1.606567] mmcblk0: mmc0:aaaa SD02G 1.89 GiB 
[    1.612701]  mmcblk0: p1 p2
[    2.266571] kjournald starting.  Commit interval 5 seconds
[    2.411407] EXT3-fs (mmcblk0p2): using internal journal
[    2.414520] EXT3-fs (mmcblk0p2): recovery complete
[    2.417144] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[    2.421142] VFS: Mounted root (ext3 filesystem) on device 179:2.
[    2.424743] Freeing init memory: 324K
modprobe: FATAL: Could not load /lib/modules/3.7.0-rc4-01279-gee05754/modules.dep: No such file or directory

INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Activating swap...done.
Cleaning up ifupdown....
Setting up networking....
Loading kernel modules...done.
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux 2.19.1
done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files....
Configuring network interfaces...done.
Cleaning up temporary files....
Setting kernel variables ...done.
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.

Debian GNU/Linux wheezy/sid armel ttyO2

armel login: 
Debian GNU/Linux wheezy/sid armel ttyO2

armel login: 
Debian GNU/Linux wheezy/sid armel ttyO2

armel login: root
Last login: Sat Jan  1 00:00:08 UTC 2000 on ttyO2
Linux armel 3.7.0-rc4-01279-gee05754 #1 SMP Wed Nov 21 16:54:06 MST 2012 armv7l

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
%% Start PM consolidated quick test


%% Preparation



root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# mount -t sysfs none /sys
mount: none already mounted or /sys busy
mount: according to mtab, sysfs is already mounted on /sys
root@armel:~# 
root@armel:~# mount -t debugfs none /debug
mount: none already mounted or /debug busy
mount: according to mtab, /debug is already mounted on /debug
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.0/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.1/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.2/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.3/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# echo 0 > /debug/pm_debug/enable_off_mode
root@armel:~# 
root@armel:~# 
%% Baseline pm_debug count dump

cat /debug/pm_debug/count
cefuse_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0
always_on_core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0
l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
mpu_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
cpu1_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cpu0_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
dss_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
gfx_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0
l3_dma_clkdm->core_pwrdm (0)
emu_sys_clkdm->emu_pwrdm (1)
l4_wkup_clkdm->wkup_pwrdm (6)
l3_dss_clkdm->dss_pwrdm (0)
iss_clkdm->cam_pwrdm (0)
l3_1_clkdm->core_pwrdm (0)
l3_2_clkdm->core_pwrdm (1)
mpuss_clkdm->mpu_pwrdm (1)
ducati_clkdm->core_pwrdm (0)
l4_ao_clkdm->always_on_core_pwrdm (0)
l3_emif_clkdm->core_pwrdm (2)
mpu1_clkdm->cpu1_pwrdm (0)
mpu0_clkdm->cpu0_pwrdm (0)
d2d_clkdm->core_pwrdm (0)
l3_init_clkdm->l3init_pwrdm (16)
l3_instr_clkdm->core_pwrdm (3)
abe_clkdm->abe_pwrdm (13)
l4_per_clkdm->l4per_pwrdm (18)
l4_secure_clkdm->l4per_pwrdm (0)
ivahd_clkdm->ivahd_pwrdm (0)
l3_gfx_clkdm->gfx_pwrdm (1)
tesla_clkdm->tesla_pwrdm (0)
l4_cfg_clkdm->core_pwrdm (0)
l4_cefuse_clkdm->cefuse_pwrdm (0)
root@armel:~# 
root@armel:~# echo enabled > /sys/devices/platform/omap_uart.2/tty/ttyO2/power/w akeup
root@armel:~#
%% Start retention double suspend/resume UART wakeup test

 
root@armel:~# echo mem > /sys/power/state
[   21.442535] PM: Syncing filesystems ... done.
[   22.209869] Freezing user space processes ... (elapsed 0.01 seconds) done.
[   22.232727] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[   22.256134] Suspending console(s) (use no_console_suspend to debug)
a
[   22.271697] PM: suspend of devices complete after 9.307 msecs
[   22.273681] PM: late suspend of devices complete after 1.953 msecs
[   22.277008] PM: noirq suspend of devices complete after 3.326 msecs
[   22.277069] Disabling non-boot CPUs ...
[   22.280609] CPU1: shutdown
[   22.284698] Successfully put all powerdomains to target state
[   22.284912] Enabling non-boot CPUs ...
[   22.287170] CPU1: Booted secondary processor
[   22.287719] CPU1 is up
[   22.289581] PM: noirq resume of devices complete after 1.831 msecs
[   22.291595] PM: early resume of devices complete after 1.251 msecs
[   22.456726] PM: resume of devices complete after 165.069 msecs
[   22.492431] Restarting tasks ... done.
root@armel:~# 
root@armel:~# a
-bash: a: command not found
root@armel:~# 
root@armel:~# 
root@armel:~# cat /debug/pm_debug/count
cefuse_pwrdm (ON),OFF:2,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0
always_on_core_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0
l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (ON),OFF:2,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
mpu_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
cpu1_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cpu0_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
dss_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
gfx_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0
l3_dma_clkdm->core_pwrdm (0)
emu_sys_clkdm->emu_pwrdm (1)
l4_wkup_clkdm->wkup_pwrdm (6)
l3_dss_clkdm->dss_pwrdm (0)
iss_clkdm->cam_pwrdm (0)
l3_1_clkdm->core_pwrdm (0)
l3_2_clkdm->core_pwrdm (1)
mpuss_clkdm->mpu_pwrdm (1)
ducati_clkdm->core_pwrdm (0)
l4_ao_clkdm->always_on_core_pwrdm (0)
l3_emif_clkdm->core_pwrdm (2)
mpu1_clkdm->cpu1_pwrdm (0)
mpu0_clkdm->cpu0_pwrdm (0)
d2d_clkdm->core_pwrdm (0)
l3_init_clkdm->l3init_pwrdm (19)
l3_instr_clkdm->core_pwrdm (3)
abe_clkdm->abe_pwrdm (13)
l4_per_clkdm->l4per_pwrdm (18)
l4_secure_clkdm->l4per_pwrdm (0)
ivahd_clkdm->ivahd_pwrdm (0)
l3_gfx_clkdm->gfx_pwrdm (1)
tesla_clkdm->tesla_pwrdm (0)
l4_cfg_clkdm->core_pwrdm (0)
l4_cefuse_clkdm->cefuse_pwrdm (0)
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# echo mem > /sys/power/state
[   24.512786] PM: Syncing filesystems ... done.
[   24.518310] Freezing user space processes ... (elapsed 0.02 seconds) done.
[   24.545196] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[   24.568634] Suspending console(s) (use no_console_suspend to debug)
a
[   24.583007] PM: suspend of devices complete after 8.239 msecs
[   24.584869] PM: late suspend of devices complete after 1.861 msecs
[   24.587982] PM: noirq suspend of devices complete after 3.082 msecs
[   24.587982] Disabling non-boot CPUs ...
[   24.589782] CPU1: shutdown
[   24.591552] Successfully put all powerdomains to target state
[   24.591735] Enabling non-boot CPUs ...
[   24.593872] CPU1: Booted secondary processor
[   24.594268] CPU1 is up
[   24.596038] PM: noirq resume of devices complete after 1.770 msecs
[   24.598052] PM: early resume of devices complete after 1.220 msecs
[   24.768859] PM: resume of devices complete after 170.776 msecs
[   24.804443] Restarting tasks ... done.
root@armel:~# 
root@armel:~# a
-bash: a: command not found
root@armel:~# 
root@armel:~# 
root@armel:~# cat /debug/pm_debug/count
cefuse_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0
always_on_core_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0
l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
dss_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
gfx_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0
l3_dma_clkdm->core_pwrdm (0)
emu_sys_clkdm->emu_pwrdm (1)
l4_wkup_clkdm->wkup_pwrdm (6)
l3_dss_clkdm->dss_pwrdm (0)
iss_clkdm->cam_pwrdm (0)
l3_1_clkdm->core_pwrdm (0)
l3_2_clkdm->core_pwrdm (1)
mpuss_clkdm->mpu_pwrdm (1)
ducati_clkdm->core_pwrdm (0)
l4_ao_clkdm->always_on_core_pwrdm (0)
l3_emif_clkdm->core_pwrdm (2)
mpu1_clkdm->cpu1_pwrdm (0)
mpu0_clkdm->cpu0_pwrdm (0)
d2d_clkdm->core_pwrdm (0)
l3_init_clkdm->l3init_pwrdm (22)
l3_instr_clkdm->core_pwrdm (3)
abe_clkdm->abe_pwrdm (13)
l4_per_clkdm->l4per_pwrdm (18)
l4_secure_clkdm->l4per_pwrdm (0)
ivahd_clkdm->ivahd_pwrdm (0)
l3_gfx_clkdm->gfx_pwrdm (1)
tesla_clkdm->tesla_pwrdm (0)
l4_cfg_clkdm->core_pwrdm (0)
l4_cefuse_clkdm->cefuse_pwrdm (0)
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# ./test_rootfs_access_nonexistent_file__ret_susp
-bash: ./test_rootfs_access_nonexistent_file__ret_susp: No such file or directory
root@armel:~# 
root@armel:~# 
%% End retention double suspend/resume UART wakeup test


%% Start retention dynamic idle UART wakeup test

echo 3000 > /sys/devices/platform/omap_uart.0/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# echo 3000 > /sys/devices/platform/omap_uart.1/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# echo 3000 > /sys/devices/platform/omap_uart.2/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# echo 3000 > /sys/devices/platform/omap_uart.3/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# cat /debug/pm_debug/count
cefuse_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0
always_on_core_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0
l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (ON),OFF:3,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
dss_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
gfx_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0
l3_dma_clkdm->core_pwrdm (0)
emu_sys_clkdm->emu_pwrdm (1)
l4_wkup_clkdm->wkup_pwrdm (6)
l3_dss_clkdm->dss_pwrdm (0)
iss_clkdm->cam_pwrdm (0)
l3_1_clkdm->core_pwrdm (0)
l3_2_clkdm->core_pwrdm (1)
mpuss_clkdm->mpu_pwrdm (1)
ducati_clkdm->core_pwrdm (0)
l4_ao_clkdm->always_on_core_pwrdm (0)
l3_emif_clkdm->core_pwrdm (2)
mpu1_clkdm->cpu1_pwrdm (0)
mpu0_clkdm->cpu0_pwrdm (0)
d2d_clkdm->core_pwrdm (0)
l3_init_clkdm->l3init_pwrdm (22)
l3_instr_clkdm->core_pwrdm (3)
abe_clkdm->abe_pwrdm (13)
l4_per_clkdm->l4per_pwrdm (15)
l4_secure_clkdm->l4per_pwrdm (0)
ivahd_clkdm->ivahd_pwrdm (0)
l3_gfx_clkdm->gfx_pwrdm (1)
tesla_clkdm->tesla_pwrdm (0)
l4_cfg_clkdm->core_pwrdm (0)
l4_cefuse_clkdm->cefuse_pwrdm (0)
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# ./test_rootfs_access_nonexistent_file__ret_dyn
-bash: ./test_rootfs_access_nonexistent_file__ret_dyn: No such file or directory
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.0/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.1/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.2/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# echo -1 > /sys/devices/platform/omap_uart.3/power/autosuspend_dela y_ms
root@armel:~# 
root@armel:~# 
%% End retention dynamic idle UART wakeup test


%% Start off-mode double suspend UART wakeup test

echo 1 > /debug/pm_debug/enable_off_mode
root@armel:~# 
root@armel:~# echo mem > /sys/power/state
[   46.606414] PM: Syncing filesystems ... done.
[   46.611450] Freezing user space processes ... (elapsed 0.02 seconds) done.
[   46.638946] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[   46.662384] Suspending console(s) (use no_console_suspend to debug)
a
[   46.676818] PM: suspend of devices complete after 8.239 msecs
[   46.678710] PM: late suspend of devices complete after 1.892 msecs
[   46.681854] PM: noirq suspend of devices complete after 3.082 msecs
[   46.681854] Disabling non-boot CPUs ...
[   46.683410] CPU1: shutdown
[   46.685028] Successfully put all powerdomains to target state
[   46.685211] Enabling non-boot CPUs ...
[   46.687316] CPU1: Booted secondary processor
[   46.687713] CPU1 is up
[   46.689483] PM: noirq resume of devices complete after 1.770 msecs
[   46.691467] PM: early resume of devices complete after 1.220 msecs
[   46.862579] PM: resume of devices complete after 171.051 msecs
[   46.898162] Restarting tasks ... done.
root@armel:~# 
root@armel:~# a
-bash: a: command not found
root@armel:~# 
root@armel:~# 
root@armel:~# cat /debug/pm_debug/count
cefuse_pwrdm (ON),OFF:4,RET:0,INA:0,ON:4,RET-LOGIC-OFF:0
always_on_core_pwrdm (ON),OFF:3,RET:0,INA:0,ON:4,RET-LOGIC-OFF:0
l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (ON),OFF:4,RET:0,INA:0,ON:4,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
mpu_pwrdm (ON),OFF:0,RET:3,INA:0,ON:4,RET-LOGIC-OFF:3,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
cpu1_pwrdm (ON),OFF:3,RET:0,INA:0,ON:4,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cpu0_pwrdm (ON),OFF:3,RET:0,INA:0,ON:4,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
dss_pwrdm (ON),OFF:3,RET:0,INA:0,ON:4,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
gfx_pwrdm (ON),OFF:3,RET:0,INA:0,ON:4,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0
l3_dma_clkdm->core_pwrdm (0)
emu_sys_clkdm->emu_pwrdm (1)
l4_wkup_clkdm->wkup_pwrdm (6)
l3_dss_clkdm->dss_pwrdm (0)
iss_clkdm->cam_pwrdm (0)
l3_1_clkdm->core_pwrdm (0)
l3_2_clkdm->core_pwrdm (1)
mpuss_clkdm->mpu_pwrdm (1)
ducati_clkdm->core_pwrdm (0)
l4_ao_clkdm->always_on_core_pwrdm (0)
l3_emif_clkdm->core_pwrdm (2)
mpu1_clkdm->cpu1_pwrdm (0)
mpu0_clkdm->cpu0_pwrdm (0)
d2d_clkdm->core_pwrdm (0)
l3_init_clkdm->l3init_pwrdm (25)
l3_instr_clkdm->core_pwrdm (3)
abe_clkdm->abe_pwrdm (13)
l4_per_clkdm->l4per_pwrdm (18)
l4_secure_clkdm->l4per_pwrdm (0)
ivahd_clkdm->ivahd_pwrdm (0)
l3_gfx_clkdm->gfx_pwrdm (1)
tesla_clkdm->tesla_pwrdm (0)
l4_cfg_clkdm->core_pwrdm (0)
l4_cefuse_clkdm->cefuse_pwrdm (0)
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# echo mem > /sys/power/state
[   48.919036] PM: Syncing filesystems ... done.
[   48.924041] Freezing user space processes ... (elapsed 0.02 seconds) done.
[   48.951446] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[   48.974884] Suspending console(s) (use no_console_suspend to debug)
a
[   48.989257] PM: suspend of devices complete after 8.209 msecs
[   48.991149] PM: late suspend of devices complete after 1.861 msecs
[   48.994232] PM: noirq suspend of devices complete after 3.051 msecs
[   48.994232] Disabling non-boot CPUs ...
[   48.995666] CPU1: shutdown
[   48.997222] Successfully put all powerdomains to target state
[   48.997406] Enabling non-boot CPUs ...
[   48.999542] CPU1: Booted secondary processor
[   48.999938] CPU1 is up
[   49.001678] PM: noirq resume of devices complete after 1.739 msecs
[   49.003662] PM: early resume of devices complete after 1.251 msecs
[   49.175170] PM: resume of devices complete after 171.478 msecs
[   49.210754] Restarting tasks ... done.
root@armel:~# 
root@armel:~# a
-bash: a: command not found
root@armel:~# 
root@armel:~# 
root@armel:~# cat /debug/pm_debug/count
cefuse_pwrdm (ON),OFF:5,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0
always_on_core_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0
l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (ON),OFF:5,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
mpu_pwrdm (ON),OFF:0,RET:4,INA:0,ON:5,RET-LOGIC-OFF:4,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
cpu1_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cpu0_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
dss_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
gfx_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0
l3_dma_clkdm->core_pwrdm (0)
emu_sys_clkdm->emu_pwrdm (1)
l4_wkup_clkdm->wkup_pwrdm (6)
l3_dss_clkdm->dss_pwrdm (0)
iss_clkdm->cam_pwrdm (0)
l3_1_clkdm->core_pwrdm (0)
l3_2_clkdm->core_pwrdm (1)
mpuss_clkdm->mpu_pwrdm (1)
ducati_clkdm->core_pwrdm (0)
l4_ao_clkdm->always_on_core_pwrdm (0)
l3_emif_clkdm->core_pwrdm (2)
mpu1_clkdm->cpu1_pwrdm (0)
mpu0_clkdm->cpu0_pwrdm (0)
d2d_clkdm->core_pwrdm (0)
l3_init_clkdm->l3init_pwrdm (28)
l3_instr_clkdm->core_pwrdm (3)
abe_clkdm->abe_pwrdm (13)
l4_per_clkdm->l4per_pwrdm (18)
l4_secure_clkdm->l4per_pwrdm (0)
ivahd_clkdm->ivahd_pwrdm (0)
l3_gfx_clkdm->gfx_pwrdm (1)
tesla_clkdm->tesla_pwrdm (0)
l4_cfg_clkdm->core_pwrdm (0)
l4_cefuse_clkdm->cefuse_pwrdm (0)
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# ./test_rootfs_access_nonexistent_file__off_susp
-bash: ./test_rootfs_access_nonexistent_file__off_susp: No such file or directory
root@armel:~# 
root@armel:~# 
%% End off-mode double suspend UART wakeup test


%% Start off-mode dynamic idle UART wakeup test

echo 3000 > /sys/devices/platform/omap_uart.0/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# echo 3000 > /sys/devices/platform/omap_uart.1/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# echo 3000 > /sys/devices/platform/omap_uart.2/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# echo 3000 > /sys/devices/platform/omap_uart.3/power/autosuspend_de lay_ms
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# cat /debug/pm_debug/count
cefuse_pwrdm (ON),OFF:5,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0
always_on_core_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0
l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
l3init_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (ON),OFF:5,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
ivahd_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
mpu_pwrdm (ON),OFF:0,RET:4,INA:0,ON:5,RET-LOGIC-OFF:4,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
cpu1_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cpu0_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
tesla_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0
dss_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
gfx_pwrdm (ON),OFF:4,RET:0,INA:0,ON:5,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0
l3_dma_clkdm->core_pwrdm (0)
emu_sys_clkdm->emu_pwrdm (1)
l4_wkup_clkdm->wkup_pwrdm (6)
l3_dss_clkdm->dss_pwrdm (0)
iss_clkdm->cam_pwrdm (0)
l3_1_clkdm->core_pwrdm (0)
l3_2_clkdm->core_pwrdm (1)
mpuss_clkdm->mpu_pwrdm (1)
ducati_clkdm->core_pwrdm (0)
l4_ao_clkdm->always_on_core_pwrdm (0)
l3_emif_clkdm->core_pwrdm (2)
mpu1_clkdm->cpu1_pwrdm (0)
mpu0_clkdm->cpu0_pwrdm (0)
d2d_clkdm->core_pwrdm (0)
l3_init_clkdm->l3init_pwrdm (28)
l3_instr_clkdm->core_pwrdm (3)
abe_clkdm->abe_pwrdm (13)
l4_per_clkdm->l4per_pwrdm (15)
l4_secure_clkdm->l4per_pwrdm (0)
ivahd_clkdm->ivahd_pwrdm (0)
l3_gfx_clkdm->gfx_pwrdm (1)
tesla_clkdm->tesla_pwrdm (0)
l4_cfg_clkdm->core_pwrdm (0)
l4_cefuse_clkdm->cefuse_pwrdm (0)
root@armel:~# 
root@armel:~# 
root@armel:~# 
root@armel:~# ./test_rootfs_access_nonexistent_file__off_dyn
-bash: ./test_rootfs_access_nonexistent_file__off_dyn: No such file or directory
root@armel:~# 
root@armel:~# 
%% End off-mode dynamic idle UART wakeup test


%% End PM consolidated quick test