怘€æ€˜€`3f<€fÀæøÀ̆ž?`??f?æžf<øž`??ð3ž<3ž<`<f<ÀÌà?̘à0˜˜fÃðÀ€˜àÃÀ˜àÀ˜ž˜à˜x~ó˜x~ðà˜˜˜03à3`?<?`?†žøž~<˜˜33žþž`?àžþž<`<f<?†øæžæž˜33€æ†f0Ì???˜83à

U-Boot 2012.07-00136-g755de79 (Aug 24 2012 - 14:19:44)

CPU  : OMAP4430 ES2.0
Board: OMAP4 Panda
I2C:   ready
DRAM:  512 MiB
MMC:   OMAP SD/MMC: 0
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  3  0 
Panda # 
Panda # setenv bootargs console=ttyO2,230400n8 vram=16M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait earlyprintk debug ignore_loglevel
Panda # loady
## Ready for binary (ymodem) download to 0x82000000 at 230400 bps...
CSending: uImage
Sending: 

Transfer complete
odem - CRC mode, 4(SOH)/4066(STX)/0(CAN) packets, 3 retries
## Total Size      = 0x003f88f0 = 4163824 Bytes
Panda # bootm
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.7.0-rc2-00158-g5d8b5c0
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4163760 Bytes = 4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Linux version 3.7.0-rc2-00158-g5d8b5c0 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Mon Nov 12 13:58:23 MST 2012
[    0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: OMAP4 Panda board
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] Reserving 16777216 bytes SDRAM for VRAM
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 126720
[    0.000000] free_area_init_node: node 0, pgdat c07ea8c0, node_mem_map c0d49000
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 125696 pages, LIFO batch:31
[    0.000000] OMAP4430 ES2.0
[    0.000000] PERCPU: Embedded 9 pages/cpu @c1151000 s12928 r8192 d15744 u36864
[    0.000000] pcpu-alloc: s12928 r8192 d15744 u36864 alloc=9*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125696
[    0.000000] Kernel command line: console=ttyO2,230400n8 vram=16M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait earlyprintk debug ignore_loglevel
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 495MB = 495MB total
[    0.000000] Memory: 488676k/488676k available, 35612k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc070b814   (7183 kB)
[    0.000000]       .init : 0xc070c000 - 0xc075c280   ( 321 kB)
[    0.000000]       .data : 0xc075e000 - 0xc07edaa0   ( 575 kB)
[    0.000000]        .bss : 0xc07edac4 - 0xc0d484ac   (5483 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[    0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.000000] ... MAX_LOCK_DEPTH:          48
[    0.000000] ... MAX_LOCKDEP_KEYS:        8191
[    0.000000] ... CLASSHASH_SIZE:          4096
[    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
[    0.000000] ... CHAINHASH_SIZE:          16384
[    0.000000]  memory used by lock dependency info: 3695 kB
[    0.000000]  per task-struct memory footprint: 1152 bytes
[    0.001251] Calibrating delay loop... 2007.19 BogoMIPS (lpj=7839744)
[    0.124847] pid_max: default: 32768 minimum: 301
[    0.125732] Security Framework initialized
[    0.126007] Mount-cache hash table entries: 512
[    0.131225] CPU: Testing write buffer coherency: ok
[    0.132537] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.133148] Setting up static identity map for 0x8051fe18 - 0x8051fe88
[    0.133239] L310 cache controller enabled
[    0.133270] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000, Cache size: 1048576 B
[    0.136627] CPU1: Booted secondary processor
[    0.203369] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.203704] Brought up 2 CPUs
[    0.203704] SMP: Total of 2 processors activated (4022.78 BogoMIPS).
[    0.212066] ttyO2 used as console in debug mode: uart2 clocks will not be gated
[    0.220428] omap_hwmod: l3_instr: _wait_target_disable failed
[    0.224731] omap_hwmod: mcpdm: cannot be enabled for reset (3)
[    0.227386] pinctrl core: initialized pinctrl subsystem
[    0.230438] regulator-dummy: no parameters
[    0.231536] NET: Registered protocol family 16
[    0.233062] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.234069] omap-gpmc omap-gpmc: error: clk_get
[    0.234100] omap-gpmc: probe of omap-gpmc failed with error -2
[    0.239868] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.240112] OMAP GPIO hardware version 0.1
[    0.241058] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.242248] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.243347] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.244445] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
[    0.245483] gpiochip_add: registered GPIOs 160 to 191 on device: gpio
[    0.248901] omap_mux_init: Add partition: #1: core, flags: 2
[    0.250457] omap_mux_init: Add partition: #2: wkup, flags: 2
[    0.250610] error setting wl12xx data: -38
[    0.250762] _omap_mux_get_by_name: Could not find signal sys_nirq
[    0.250793] _omap_mux_get_by_name: Could not find signal sys_nirq
[    0.254150] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[    0.254180] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx
[    0.306030] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.306060] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.314392] OMAP DMA hardware revision 0.0
[    0.317047] ARM PMU: not yet supported on OMAP4430 due to missing CTI driver
[    0.344848] bio: create slab <bio-0> at 0
[    0.386749] omap-dma-engine omap-dma-engine: OMAP DMA engine driver
[    0.387451] vwl1271: 1800 mV 
[    0.390136] SCSI subsystem initialized
[    0.391357] usbcore: registered new interface driver usbfs
[    0.391601] usbcore: registered new interface driver hub
[    0.391967] usbcore: registered new device driver usb
[    0.409667] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[    0.411193] twl 1-0048: PIH (irq 39) chaining IRQs 416..436
[    0.412750] VUSB: 3300 mV normal standby
[    0.413787] vdd_mpu: 500 <--> 1500 mV normal 
[    0.415466] vdd_iva: 500 <--> 1500 mV normal 
[    0.416412] vdd_core: 500 <--> 1500 mV normal 
[    0.417724] V1V8: 1800 mV normal standby
[    0.418670] V2V1: 2100 mV normal standby
[    0.419830] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[    0.421081] VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[    0.423522] VCXIO: 1800 mV normal standby
[    0.423583] VCXIO: supplied by V2V1
[    0.425659] VDAC: 1800 mV normal standby
[    0.425689] VDAC: supplied by V2V1
[    0.427276] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[    0.428588] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[    0.430114] VANA: 2100 mV normal standby
[    0.430786] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
[    0.446258] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
[    0.462127] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[    0.477416] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
[    0.481262] Switching to clocksource 32k_counter
[    0.543792] NET: Registered protocol family 2
[    0.545532] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.545959] TCP bind hash table entries: 16384 (order: 7, 589824 bytes)
[    0.550079] TCP: Hash tables configured (established 16384 bind 16384)
[    0.550384] TCP: reno registered
[    0.550415] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    0.550567] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    0.551208] NET: Registered protocol family 1
[    0.552276] RPC: Registered named UNIX socket transport module.
[    0.552307] RPC: Registered udp transport module.
[    0.552307] RPC: Registered tcp transport module.
[    0.552307] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.553009] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.706176] VFS: Disk quotas dquot_6.5.2
[    0.706329] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.708251] NFS: Registering the id_resolver key type
[    0.708526] Key type id_resolver registered
[    0.708526] Key type id_legacy registered
[    0.708618] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.709075] msgmni has been set to 954
[    0.710876] io scheduler noop registered
[    0.710876] io scheduler deadline registered
[    0.710968] io scheduler cfq registered (default)
[    0.713287] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.716857] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[    0.718017] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[    0.718719] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[    1.160888] console [ttyO2] enabled
[    1.163574] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[    1.183013] brd: module loaded
[    1.193878] loop: module loaded
[    1.198394] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.202331] OneNAND driver initializing
[    1.210113] usbcore: registered new interface driver asix
[    1.213287] usbcore: registered new interface driver cdc_ether
[    1.216766] usbcore: registered new interface driver smsc95xx
[    1.220123] usbcore: registered new interface driver net1080
[    1.223419] usbcore: registered new interface driver cdc_subset
[    1.226928] usbcore: registered new interface driver zaurus
[    1.230224] usbcore: registered new interface driver cdc_ncm
[    1.234374] usbcore: registered new interface driver cdc_wdm
[    1.237487] Initializing USB Mass Storage driver...
[    1.240447] usbcore: registered new interface driver usb-storage
[    1.243713] USB Mass Storage support registered.
[    1.246490] usbcore: registered new interface driver usbtest
[    1.250457] mousedev: PS/2 mouse device common for all mice
[    1.256652] twl_rtc twl_rtc: Power up reset detected.
[    1.260192] twl_rtc twl_rtc: Enabling TWL-RTC
[    1.265960] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[    1.269836] i2c /dev entries driver
[    1.273803] Driver for 1-wire Dallas network protocol.
[    1.278533] omap_wdt: OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[    1.284179] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk
[    1.287567] omap-dma-engine omap-dma-engine: allocating channel for 62
[    1.291168] omap-dma-engine omap-dma-engine: allocating channel for 61
[    1.348999] omap_hsmmc omap_hsmmc.4: Failed to get debounce clk
[    1.352264] omap-dma-engine omap-dma-engine: allocating channel for 60
[    1.355834] omap-dma-engine omap-dma-engine: allocating channel for 59
[    1.478454] usbcore: registered new interface driver usbhid
[    1.481597] usbhid: USB HID core driver
[    1.484527] oprofile: no performance counters
[    1.488159] oprofile: using timer interrupt.
[    1.491119] TCP: cubic registered
[    1.492980] Initializing XFRM netlink socket
[    1.495391] NET: Registered protocol family 17
[    1.497894] NET: Registered protocol family 15
[    1.500579] Key type dns_resolver registered
[    1.503051] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[    1.512695] omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).
[    1.517059] omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).[    1.522491] Power Management for TI OMAP4.
[    1.524902] ThumbEE CPU extension supported.
[    1.530761] VANA: incomplete constraints, leaving on
[    1.536712] VDAC: incomplete constraints, leaving on
[    1.540222] VUSB: incomplete constraints, leaving on
[    1.545349] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    1.552795] Waiting for root device /dev/mmcblk0p2...
[    1.660888] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.665527] mmc0: new SD card at address aaaa
[    1.669433] mmcblk0: mmc0:aaaa SD02G 1.89 GiB 
[    1.675659]  mmcblk0: p1 p2
[    3.182373] kjournald starting.  Commit interval 5 seconds
[    3.325897] EXT3-fs (mmcblk0p2): using internal journal
[    3.466003] EXT3-fs (mmcblk0p2): recovery complete
[    3.468627] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[    3.472625] VFS: Mounted root (ext3 filesystem) on device 179:2.
[    3.476226] Freeing init memory: 320K
modprobe: FATAL: Could not load /lib/modules/3.7.0-rc2-00158-g5d8b5c0/modules.dep: No such file or directory

INIT: version 2.88 booting
Using makefile-style concurrent boot in runlevel S.
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...