CCCSending /srv/serial/u-boot-spl.bin, 784 blocks: Give your local XMODEM receive command now. Transfer complete ot SPL 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 CSending: u-boot.bin Sending: Transfer complete m - CRC mode, 3(SOH)/375(STX)/0(CAN) packets, 3 retries Loaded 384084 bytes U-Boot 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 U-Boot# U-Boot# setenv autoload off; setenv serverip 192.168.57.1; dhcp cpsw Waiting for PHY auto negotiation to complete.. done link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.138 U-Boot# tftp 0x81000000 zImage.omap2plus_defconfig link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'zImage.omap2plus_defconfig'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################# 1.1 MiB/s done Bytes transferred = 4231288 (409078 hex) U-Boot# tftp 0x82000000 am335x-bone.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'am335x-bone.dtb'. Load address: 0x82000000 Loading: *## 1 MiB/s done Bytes transferred = 17315 (43a3 hex) U-Boot# setenv bootargs console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp U-Boot# U-Boot# bootz 0x81000000 - 0x82000000 ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 82000000, end 820073a2 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.13.0-rc3-36687-g6d4c883 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Thu Dec 26 02:24:31 MST 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at 8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c0875cc0, node_mem_map c0de1000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0fed000 s13952 r8192 d14720 u36864 [ 0.000000] pcpu-alloc: s13952 r8192 d14720 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 228132K/261120K available (5475K kernel code, 660K rwdata, 2128K rodata, 385K init, 5527K bss, 32988K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0774f3c (7604 kB) [ 0.000000] .init : 0xc0775000 - 0xc07d5680 ( 386 kB) [ 0.000000] .data : 0xc07d6000 - 0xc087b100 ( 661 kB) [ 0.000000] .bss : 0xc087b100 - 0xc0de0f70 (5528 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000000] OMAP clocksource: timer1 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.001492] Calibrating delay loop... 545.58 BogoMIPS (lpj=2727936) [ 0.109381] pid_max: default: 32768 minimum: 301 [ 0.110012] Security Framework initialized [ 0.110203] Mount-cache hash table entries: 512 [ 0.129510] CPU: Testing write buffer coherency: ok [ 0.131407] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.131502] Setting up static identity map for 0x80531060 - 0x805310d0 [ 0.136463] Brought up 1 CPUs [ 0.136487] SMP: Total of 1 processors activated. [ 0.136503] CPU: All CPU(s) started in SVC mode. [ 0.140968] devtmpfs: initialized [ 0.155287] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.184938] omap_hwmod: debugss: _wait_target_disable failed [ 0.249939] pinctrl core: initialized pinctrl subsystem [ 0.255916] regulator-dummy: no parameters [ 0.260671] NET: Registered protocol family 16 [ 0.269749] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.295946] platform 49000000.edma: alias fck already exists [ 0.295994] platform 49000000.edma: alias fck already exists [ 0.296024] platform 49000000.edma: alias fck already exists [ 0.300539] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.302341] OMAP GPIO hardware version 0.1 [ 0.305934] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.310234] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.314310] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.339135] No ATAGs? [ 0.339168] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.432551] bio: create slab at 0 [ 0.488890] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.490904] of_get_named_gpiod_flags: can't parse gpios property of node '/fixedregulator@0[0]' [ 0.492339] vmmcsd_fixed: 3300 mV [ 0.503507] SCSI subsystem initialized [ 0.506518] usbcore: registered new interface driver usbfs [ 0.507198] usbcore: registered new interface driver hub [ 0.508281] usbcore: registered new device driver usb [ 0.513154] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 0.513220] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.525456] Switched to clocksource timer1 [ 0.750763] NET: Registered protocol family 2 [ 0.753386] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.753647] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.754899] TCP: Hash tables configured (established 2048 bind 2048) [ 0.755162] TCP: reno registered [ 0.755206] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.755827] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.757793] NET: Registered protocol family 1 [ 0.760194] RPC: Registered named UNIX socket transport module. [ 0.760223] RPC: Registered udp transport module. [ 0.760241] RPC: Registered tcp transport module. [ 0.760258] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.762057] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.014910] VFS: Disk quotas dquot_6.5.2 [ 1.015476] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.018843] NFS: Registering the id_resolver key type [ 1.019410] Key type id_resolver registered [ 1.019439] Key type id_legacy registered [ 1.019611] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.020318] msgmni has been set to 477 [ 1.025882] io scheduler noop registered [ 1.025915] io scheduler deadline registered [ 1.026009] io scheduler cfq registered (default) [ 1.030431] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 1.036561] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.047093] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@44e09000[0]' [ 1.048949] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.753960] console [ttyO0] enabled [ 1.764719] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 1.813940] brd: module loaded [ 1.843154] loop: module loaded [ 1.857989] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.877744] usbcore: registered new interface driver asix [ 1.884051] usbcore: registered new interface driver ax88179_178a [ 1.891314] usbcore: registered new interface driver cdc_ether [ 1.898766] usbcore: registered new interface driver r815x [ 1.905183] usbcore: registered new interface driver smsc95xx [ 1.912049] usbcore: registered new interface driver net1080 [ 1.918975] usbcore: registered new interface driver cdc_subset [ 1.925967] usbcore: registered new interface driver zaurus [ 1.932509] usbcore: registered new interface driver cdc_ncm [ 1.941485] usbcore: registered new interface driver cdc_wdm [ 1.948417] usbcore: registered new interface driver usb-storage [ 1.955720] usbcore: registered new interface driver usbtest [ 1.965948] mousedev: PS/2 mouse device common for all mice [ 1.980085] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 1.989835] i2c /dev entries driver [ 1.994084] Driver for 1-wire Dallas network protocol. [ 2.007118] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.018984] of_get_named_gpiod_flags exited with status 0 [ 2.024664] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@48060000[0]' [ 2.035129] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 2.042464] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 2.050209] omap_hsmmc 48060000.mmc: vmmc regulator missing [ 2.056447] edma-dma-engine edma-dma-engine.0: freeing channel for 24 [ 2.063214] edma-dma-engine edma-dma-engine.0: freeing channel for 25 [ 2.070353] platform 48060000.mmc: Driver omap_hsmmc requests probe deferral [ 2.079343] of_get_named_gpiod_flags exited with status 0 [ 2.085031] of_get_named_gpiod_flags exited with status 0 [ 2.090893] of_get_named_gpiod_flags exited with status 0 [ 2.096625] of_get_named_gpiod_flags exited with status 0 [ 2.102304] of_get_named_gpiod_flags exited with status 0 [ 2.109878] of_get_named_gpiod_flags exited with status 0 [ 2.116698] of_get_named_gpiod_flags exited with status 0 [ 2.123224] of_get_named_gpiod_flags exited with status 0 [ 2.132786] ledtrig-cpu: registered to indicate activity on CPUs [ 2.141767] usbcore: registered new interface driver usbhid [ 2.147808] usbhid: USB HID core driver [ 2.155212] oprofile: using arm/armv7 [ 2.160377] TCP: cubic registered [ 2.163869] Initializing XFRM netlink socket [ 2.168609] NET: Registered protocol family 17 [ 2.173385] NET: Registered protocol family 15 [ 2.178613] Key type dns_resolver registered [ 2.186328] ThumbEE CPU extension supported. [ 2.214806] DCDC1: at 1500 mV [ 2.221942] vdd_mpu: 925 <--> 1325 mV at 1100 mV [ 2.230523] vdd_core: 925 <--> 1150 mV at 1100 mV [ 2.238792] LDO1: at 1800 mV [ 2.244795] LDO2: at 3300 mV [ 2.251025] LDO3: 1800 <--> 3300 mV at 1800 mV [ 2.258951] LDO4: at 3300 mV [ 2.265072] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 2.271030] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.278152] of_get_named_gpiod_flags exited with status 0 [ 2.283828] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@48060000[0]' [ 2.293573] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 2.300832] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 2.309963] 48060000.mmc supply vmmc_aux not found, using dummy regulator [ 2.425454] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.431868] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.442314] libphy: 4a101000.mdio: probed [ 2.446722] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.459287] Detected MACID = 78:c5:e5:c3:1e:2a [ 2.470872] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 2.482845] net eth0: initializing cpsw version 1.12 (0) [ 2.491023] net eth0: phy found : id is : 0x7c0f1 [ 2.496225] libphy: PHY 4a101000.mdio:01 not found [ 2.501252] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 5.565908] libphy: 4a101000.mdio:00 - Link is Up - 100/Full [ 5.585400] Sending DHCP requests ., OK [ 5.605837] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.138 [ 5.614852] IP-Config: Complete: [ 5.618370] device=eth0, hwaddr=78:c5:e5:c3:1e:2a, ipaddr=192.168.57.138, mask=255.255.255.0, gw=255.255.255.255 [ 5.629566] host=192.168.57.138, domain=example.org, nis-domain=(none) [ 5.636920] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.643665] nameserver0=192.168.57.1 [ 5.650585] omap_uart 44e09000.serial: no wakeirq for uart0 [ 5.681866] VFS: Mounted root (nfs filesystem) on device 0:13. [ 5.690873] devtmpfs: mounted [ 5.695061] Freeing unused kernel memory: 384K (c0775000 - c07d5000) [ 6.161745] omap_uart 44e09000.serial: no wakeirq for uart0 [ 6.176985] omap_uart 44e09000.serial: no wakeirq for uart0 INIT: [ 6.196292] omap_uart 44e09000.serial: no wakeirq for uart0 version 2.88 booting[ 6.216184] omap_uart 44e09000.serial: no wakeirq for uart0 [ 6.247273] omap_uart 44e09000.serial: no wakeirq for uart0 [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.548361] udevd[729]: starting version 175 [ ok . [....] Synthesizing the initial hotplug events...udevd[768]: error changing net interface name eth0 to eth4: Device or resource busy [ ok done. [....] Waiting for /dev to be fully populated...[ ok done. [....] Activating swap...[ ok done. [ 15.045362] random: nonblocking pool is initialized [....] Cleaning up temporary files... /tmp[ ok . [....] Activating lvm and md swap...[ ok done. [....] Checking file systems...fsck from util-linux 2.20.1 [ ok done. [....] Mounting local filesystems...[ ok done. [....] Activating swapfile swap...[ ok done. [....] Cleaning up temporary files...[ ok . [....] Setting kernel variables ...[ ok done. [....] Configuring network interfaces...[ ok done. [....] Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 [ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [....] Cleaning up temporary files...[ ok . [....] Starting network benchmark server[ ok . [ 33.066455] omap_uart 44e09000.serial: no wakeirq for uart0 INIT: [ 33.086210] omap_uart 44e09000.serial: no wakeirq for uart0 Entering runlevel: 2[ 33.106165] omap_uart 44e09000.serial: no wakeirq for uart0 [ 33.137458] omap_uart 44e09000.serial: no wakeirq for uart0 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting network benchmark server[FAIL failed! [....] Starting system message bus: dbus[ ok . [....] Starting rpcbind daemon...[....] Already running.[ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [ 37.462789] omap_uart 44e09000.serial: no wakeirq for uart0 Debian GNU/Linux wheezy/sid armel ttyO0 armel login: