$ NOLO X-Loader (v1.1.16, Oct 31 2008) Secondary image size 99036 Booting secondary Nokia OMAP Loader v1.1.16 (Oct 31 2008) running on Nokia N800 F5 (RX-34) Clocks: Core: 658 MHz L3: 109 MHz L4: 109 MHz MPU: 329 MHz DSP: 219 MHz IVA: 109 MHz I2C v3.4 Menelaus v2.2 found Vilma v1.5 found Betty v2.1 found Reset reason: pwr_key System DMA v2.0 OneNAND blocks unlocked in 30264 us Flash id: ec4811 Partition table successfully read McSPI v1.4 RFBI version 1.0 Detecting LCD panel lph8923 Panel ID: 838f48 URAL panel detected Detected LCD panel: ls041y3 S1D13745 Hailstorm detected FB memory blanking took 242 ms (3089 kB/s) Logo drawn in 24 ms (1218 kB/s) Über-cool backlight fade-in took 101 ms Initializing USB USB host detected Entering USB loop SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 64 bytes) SETUP: WR STD DEVICE SET_ADDRESS value 0016 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 18 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 9 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 94 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 00, index 0000, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 02, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 01, index 0409, length 255 bytes) SETUP: WR STD DEVICE SET_CONFIGURATION value 0001 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 03, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0001 index 0002 length 0000 Flashing interface selected SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 Flashing mode entered SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 SETUP: RD VND DEVICE req 04 value 0000 index 0000 length 0200 SETUP: RD VND DEVICE req 03 value 0000 index 0000 length 0004 SETUP: WR VND DEVICE req 12 value 0000 index 0000 length 0012 SETUP: RD VND DEVICE req 14 value 0000 index 0000 length 0200 SETUP: WR VND DEVICE req 42 value 0000 index 0000 length 001b Receiving kernel (length 2041600) Image successfully received SETUP: WR VND DEVICE req 82 value 0000 index 0000 length 0000 SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 Boot requested Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.6.0-rc4-00006-g6d56e0e (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Wed Sep 5 14:37:32 MDT 2012 [ 0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Nokia N800 [ 0.000000] Ignoring unrecognised tag 0x414f4d50 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c0413768, node_mem_map c093c000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] OMAP2420 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttyO2,115200 earlyprintk debug init=/bin/bash [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 120440k/120440k available, 10632k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc03a3e38 (3696 kB) [ 0.000000] .init : 0xc03a4000 - 0xc03caecc ( 156 kB) [ 0.000000] .data : 0xc03cc000 - 0xc0414200 ( 289 kB) [ 0.000000] .bss : 0xc0414224 - 0xc093b098 (5276 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] NR_IRQS:474 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.063720] Calibrating delay loop... 218.45 BogoMIPS (lpj=851968) [ 0.121673] pid_max: default: 32768 minimum: 301 [ 0.127197] Security Framework initialized [ 0.131713] Mount-cache hash table entries: 512 [ 0.146606] CPU: Testing write buffer coherency: ok [ 0.153991] hw perfevents: enabled with v6 PMU driver, 3 counters available [ 0.161743] Setting up static identity map for 0x802911c8 - 0x80291238 [ 0.183624] ttyO2 used as console in debug mode uart2 clocks will not be gated [ 0.212738] dummy: [ 0.219177] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.226654] GPMC revision 2.0 [ 0.230407] gpmc: irq-20 could not claim: err -22 [ 0.251129] omap_gpio omap_gpio.0: Could not get gpio dbck [ 0.260986] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.268646] OMAP GPIO hardware version 1.8 [ 0.274169] omap_gpio omap_gpio.1: Could not get gpio dbck [ 0.282470] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.291534] omap_gpio omap_gpio.2: Could not get gpio dbck [ 0.300262] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.308746] omap_gpio omap_gpio.3: Could not get gpio dbck [ 0.316558] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.338958] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.404357] mmci-omap.0: alias fck already exists [ 0.411224] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.420410] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.429534] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.438629] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.447753] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.456878] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.465972] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.473114] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.515624] OMAP DMA hardware revision 2.0 [ 0.609558] bio: create slab at 0 [ 0.632293] SCSI subsystem initialized [ 0.641204] omap_i2c omap_i2c.1: bus 1 rev1.3.4 at 400 kHz [ 0.654815] omap_i2c omap_i2c.2: bus 2 rev1.3.4 at 400 kHz [ 0.672485] Switching to clocksource 32k_counter [ 0.822784] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.861541] VFS: Disk quotas dquot_6.5.2 [ 0.866058] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.875762] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.884948] msgmni has been set to 235 [ 0.898437] io scheduler noop registered [ 0.902618] io scheduler deadline registered [ 0.907409] io scheduler cfq registered (default) [ 0.923431] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.947692] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 0.960540] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 0.971435] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 74) is a OMAP UART2 [ 0.979644] console [ttyO2] enabled, bootconsole disabled [ 0.979644] console [ttyO2] enabled, bootconsole disabled [ 1.001831] omap_rng omap_rng: OMAP Random Number Generator ver. 40 [ 1.086334] brd: module loaded [ 1.134704] loop: module loaded [ 1.141326] Menelaus rev 2.2 [ 1.176452] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.185943] OneNAND driver initializing [ 1.191650] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c88c0000, freq 54 MHz [ 1.203124] OneNAND Manufacturer: Samsung (0xec) [ 1.208007] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48) [ 1.213623] OneNAND version = 0x0011 [ 1.217468] Chip support all block unlock [ 1.221771] onenand_wait: controller error! state 15 ctrl 0x0440 intr 0x8000 [ 1.230895] Scanning device for bad blocks [ 1.243225] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x39 addr8 0x0 [ 1.251586] OneNAND eraseblock 57 is an initial bad block [ 1.257446] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3a addr8 0x0 [ 1.265777] OneNAND eraseblock 58 is an initial bad block [ 1.271606] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3b addr8 0x0 [ 1.279937] OneNAND eraseblock 59 is an initial bad block [ 1.298400] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xa7 addr8 0x0 [ 1.306732] OneNAND eraseblock 167 is an initial bad block [ 1.314178] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xb5 addr8 0x0 [ 1.322479] OneNAND eraseblock 181 is an initial bad block [ 1.360931] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x1c9 addr8 0x0 [ 1.369354] OneNAND eraseblock 457 is an initial bad block [ 1.565826] Creating 5 MTD partitions on "omap2-onenand": [ 1.571655] 0x000000000000-0x000000020000 : "bootloader" [ 1.593200] 0x000000020000-0x000000080000 : "config" [ 1.609405] 0x000000080000-0x000000280000 : "kernel" [ 1.626159] 0x000000280000-0x000000680000 : "initfs" [ 1.642608] 0x000000680000-0x000010000000 : "rootfs" [ 1.693542] spi spi2.0: no RX DMA engine channel for McSPI [ 1.699371] omap2_mcspi omap2_mcspi.2: can't setup spi2.0, status -11 [ 1.706298] omap2_mcspi omap2_mcspi.2: can't create new device for p54spi [ 1.719604] mousedev: PS/2 mouse device common for all mice [ 1.737823] i2c /dev entries driver [ 1.749206] Driver for 1-wire Dallas network protocol. [ 1.762695] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec [ 1.776550] mmci-omap mmci-omap.0: unable to obtain TX DMA engine channel 61 [ 1.784149] mmci-omap mmci-omap.0: unable to obtain RX DMA engine channel 62 [ 1.899261] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.906646] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.930816] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.937408] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.944030] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.950531] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.981384] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 1.989990] mux: Failed to setup hwmod io irq -22 [ 2.009033] Power Management for OMAP2 initializing [ 2.014343] PRCM revision 1.0 [ 2.057312] clock: disabling unused clocks to save power [ 2.075500] /home/paul/linux/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.092681] Waiting for root device /dev/mmcblk0p1... [ 2.348999] Unhandled fault: imprecise external abort (0x406) at 0x00000000 [ 2.356353] Internal error: : 406 [#1] ARM [ 2.360687] Modules linked in: [ 2.363922] CPU: 0 Not tainted (3.6.0-rc4-00006-g6d56e0e #1) [ 2.370239] PC is at default_idle+0x30/0x3c [ 2.374664] LR is at trace_hardirqs_on_caller+0x15c/0x1b0 [ 2.380371] pc : [] lr : [] psr: 20000013 [ 2.380371] sp : c03cdfb8 ip : c03fb9a8 fp : 00000000 [ 2.392425] r10: 803c0c30 r9 : 4107b362 r8 : 80004008 [ 2.397918] r7 : c0a3d900 r6 : c03c1f7c r5 : ffffffff r4 : c03cc000 [ 2.404785] r3 : c03d6168 r2 : 00000000 r1 : 00000004 r0 : 00000001 [ 2.411682] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel [ 2.419342] Control: 00c5387d Table: 80004000 DAC: 00000017 [ 2.425384] Process swapper (pid: 0, stack limit = 0xc03cc2e8) [ 2.431549] Stack: (0xc03cdfb8 to 0xc03ce000) [ 2.436126] dfa0: c0013804 c00139cc [ 2.444763] dfc0: c03d49b8 c03a471c ffffffff ffffffff c03a41cc 00000000 00000000 c03c1f7c [ 2.453369] dfe0: 00000000 00c5387d c03d4108 c03c1f4c c03d7614 80008040 00000000 00000000 [ 2.462005] [] (default_idle+0x30/0x3c) from [] (cpu_idle+0x60/0xcc) [ 2.470550] [] (cpu_idle+0x60/0xcc) from [] (start_kernel+0x290/0x2e0) [ 2.479278] [] (start_kernel+0x290/0x2e0) from [<80008040>] (0x80008040) [ 2.487274] Code: e5933014 e12fff33 eb0158bc f1080080 (e8bd8008) [ 2.493682] ---[ end trace f59e8c9abda8bfae ]--- [ 2.498565] Kernel panic - not syncing: Attempted to kill the idle task!