Texas Instruments X-Loader 1.47 (Jan 14 2011 - 15:43:28) Starting X-loader on MMC Reading boot sector 212836 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... U-Boot 2010.06 (Jan 14 2011 - 15:43:45) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 EVM board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB In: serial Out: serial Err: serial Read back SMSC id 0x92200000 Die ID #368000229ff80000016071640902c013 Net: smc911x-0 Hit any key to stop autoboot: 3  0 OMAP3_EVM # OMAP3_EVM # setenv bootfile uImage-dtb.omap3-evm-37xx OMAP3_EVM # OMAP3_EVM # dhcp smc911x: detected LAN9220 controller smc911x: phy initialized smc911x: MAC 00:50:c2:7e:99:42 BOOTP broadcast 1 DHCP client bound to address 192.168.57.131 Using smc911x-0 device TFTP from server 192.168.57.1; our IP address is 192.168.57.131 Filename 'uImage-dtb.omap3-evm-37xx'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################### done Bytes transferred = 4815701 (497b55 hex) OMAP3_EVM # setenv bootargs console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh OMAP3_EVM # OMAP3_EVM # bootm ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4815637 Bytes = 4.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.0-rc1-103805-geb039a1 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Thu Nov 20 02:02:11 MST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP37XX EVM (TMDSEVM3730) [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c0974840, node_mem_map cfcf1000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] HighMem zone: 1048574 pages exceeds freesize 0 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] PERCPU: Embedded 11 pages/cpu @cfc7b000 s14976 r8192 d21888 u45056 [ 0.000000] pcpu-alloc: s14976 r8192 d21888 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] allocated 522240 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 223432K/261120K available (6251K kernel code, 680K rwdata, 2320K rodata, 420K init, 8264K bss, 37688K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0866f54 (8572 kB) [ 0.000000] .init : 0xc0867000 - 0xc08d0000 ( 420 kB) [ 0.000000] .data : 0xc08d0000 - 0xc097a310 ( 681 kB) [ 0.000000] .bss : 0xc097a310 - 0xc118c368 (8265 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000061] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001190] Console: colour dummy device 80x30 [ 0.001251] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001251] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001281] ... MAX_LOCK_DEPTH: 48 [ 0.001281] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001281] ... CLASSHASH_SIZE: 4096 [ 0.001312] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001312] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001342] ... CHAINHASH_SIZE: 32768 [ 0.001342] memory used by lock dependency info: 5167 kB [ 0.001342] per task-struct memory footprint: 1152 bytes [ 0.001403] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696) [ 0.097595] pid_max: default: 32768 minimum: 301 [ 0.098144] Security Framework initialized [ 0.098388] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.098388] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.102111] Initializing cgroup subsys memory [ 0.102203] Initializing cgroup subsys devices [ 0.102325] Initializing cgroup subsys freezer [ 0.102447] Initializing cgroup subsys blkio [ 0.102539] Initializing cgroup subsys perf_event [ 0.102661] CPU: Testing write buffer coherency: ok [ 0.104309] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.104461] Setting up static identity map for 0x805ec800 - 0x805ec870 [ 0.109558] Brought up 1 CPUs [ 0.109588] SMP: Total of 1 processors activated. [ 0.109588] CPU: All CPU(s) started in SVC mode. [ 0.113586] devtmpfs: initialized [ 0.116607] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.197723] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.200042] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.309387] pinctrl core: initialized pinctrl subsystem [ 0.312957] regulator-dummy: no parameters [ 0.409545] NET: Registered protocol family 16 [ 0.418090] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.421569] cpuidle: using governor ladder [ 0.421630] cpuidle: using governor menu [ 0.421813] omap_l3_smx omap_l3_smx.0: couldn't request debug irq [ 0.421936] omap_l3_smx: probe of omap_l3_smx.0 failed with error -22 [ 0.430328] Reprogramming SDRC clock to 400000000 Hz [ 0.444091] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.445373] OMAP GPIO hardware version 2.5 [ 0.447479] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.450500] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.453277] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.456054] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.458923] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.460540] irq: no irq domain found for /ocp/pinmux@48002030 ! [ 0.461456] irq: no irq domain found for /ocp/pinmux@48002030 ! [ 0.462341] irq: no irq domain found for /ocp/pinmux@48002030 ! [ 0.487701] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 0.489288] gpmc_probe_nand_child: ti,elm-id property not found [ 0.489501] gpmc_cs_program_settings: invalid width 0! [ 0.492156] platform 48058000.ssi-controller: Cannot lookup hwmod 'ssi' [ 0.500793] No ATAGs? [ 0.500823] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.504302] OMAP DMA hardware revision 5.0 [ 0.539825] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.539916] edma-dma-engine: probe of edma-dma-engine.0 failed with error -22 [ 0.592346] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.593597] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vddvario[0]' [ 0.594360] vddvario: no parameters [ 0.594879] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vdd33a[0]' [ 0.595458] vdd33a: no parameters [ 0.596130] reg-fixed-voltage wl12xx_vmmc: could not find pctldev for node /ocp/pinmux@48002030/pinmux_wl12xx_gpio, deferring probe [ 0.596160] platform wl12xx_vmmc: Driver reg-fixed-voltage requests probe deferral [ 0.596405] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-lcd-3v3[0]' - status (0) [ 0.597259] lcd_3v3: 3300 mV [ 0.603210] SCSI subsystem initialized [ 0.604339] usbcore: registered new interface driver usbfs [ 0.604553] usbcore: registered new interface driver hub [ 0.604766] usbcore: registered new device driver usb [ 0.611999] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz [ 0.613647] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz [ 0.617767] omap_i2c 48060000.i2c: bus 2 rev4.4 at 400 kHz [ 0.624084] Switched to clocksource 32k_counter [ 0.832580] NET: Registered protocol family 2 [ 0.835083] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.835327] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.836456] TCP: Hash tables configured (established 2048 bind 2048) [ 0.836669] TCP: reno registered [ 0.836730] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.837036] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.838714] NET: Registered protocol family 1 [ 0.840850] RPC: Registered named UNIX socket transport module. [ 0.840881] RPC: Registered udp transport module. [ 0.840881] RPC: Registered tcp transport module. [ 0.840911] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.842803] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.850952] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.851226] audit: initializing netlink subsys (disabled) [ 0.851501] audit: type=2000 audit(0.830:1): initialized [ 0.857482] VFS: Disk quotas dquot_6.5.2 [ 0.857696] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.860900] NFS: Registering the id_resolver key type [ 0.861389] Key type id_resolver registered [ 0.861389] Key type id_legacy registered [ 0.861663] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.864379] msgmni has been set to 468 [ 0.869415] io scheduler noop registered [ 0.869476] io scheduler deadline registered [ 0.869598] io scheduler cfq registered (default) [ 0.873535] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568 [ 0.874511] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92 [ 0.875701] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size 92 [ 0.880126] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV [ 0.882446] abb_mpu_iva: 1012 <--> 1375 mV [ 0.884735] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.893707] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.894561] omap_uart 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 224, base_baud = 3000000) is a OMAP UART0 [ 1.860290] console [ttyO0] enabled [ 1.866943] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 1.877410] omap_uart 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 225, base_baud = 3000000) is a OMAP UART1 [ 1.890441] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@49020000[0]' [ 1.900787] omap_uart 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 226, base_baud = 3000000) is a OMAP UART2 [ 1.913665] omap_uart 49042000.serial: no wakeirq for uart0 [ 1.919677] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@49042000[0]' [ 1.929931] omap_uart 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 260, base_baud = 3000000) is a OMAP UART3 [ 1.974517] brd: module loaded [ 1.996246] loop: module loaded [ 2.010986] twl 0-0048: PIH (irq 294) chaining IRQs 298..306 [ 2.017517] twl 0-0048: power (irq 303) chaining IRQs 306..313 [ 2.030029] VAUX1: at 3000 mV [ 2.036346] VAUX2_4030: at 1800 mV [ 2.042694] VAUX3: at 2800 mV [ 2.049285] VAUX4: at 2800 mV [ 2.055297] VDD1: 600 <--> 1450 mV at 1200 mV [ 2.062561] VDAC: 1800 mV [ 2.070129] VIO: at 1800 mV [ 2.076568] VINTANA1: 1500 mV [ 2.083007] VINTANA2: at 2750 mV [ 2.089813] VINTDIG: 1500 mV [ 2.095367] VMMC1: 1850 <--> 3150 mV at 3000 mV [ 2.102874] VMMC2: 1850 <--> 3150 mV at 2600 mV [ 2.110137] VUSB1V5: 1500 mV [ 2.115386] VUSB1V8: 1800 mV [ 2.120483] VUSB3V1: 3100 mV [ 2.126861] VPLL1: at 1800 mV [ 2.134063] VPLL2: 1800 mV [ 2.139739] VSIM: 1800 <--> 3000 mV at 1800 mV [ 2.147064] twl4030_gpio twl4030-gpio: gpio (irq 298) chaining IRQs 314..331 [ 2.155029] gpiochip_find_base: found new base at 492 [ 2.161041] gpiochip_add: registered GPIOs 492 to 511 on device: twl4030 [ 2.231231] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.258636] libphy: smsc911x-mdio: probed [ 2.263366] smsc911x 2c000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=2c000000.etherne:01, irq=-1) [ 2.275848] smsc911x 2c000000.ethernet eth0: MAC Address: 00:50:c2:7e:99:42 [ 2.285430] usbcore: registered new interface driver asix [ 2.291320] usbcore: registered new interface driver ax88179_178a [ 2.298004] usbcore: registered new interface driver cdc_ether [ 2.304443] usbcore: registered new interface driver smsc95xx [ 2.310638] usbcore: registered new interface driver net1080 [ 2.316833] usbcore: registered new interface driver cdc_subset [ 2.323242] usbcore: registered new interface driver zaurus [ 2.329467] usbcore: registered new interface driver cdc_ncm [ 2.337005] usbcore: registered new interface driver cdc_wdm [ 2.343231] usbcore: registered new interface driver usb-storage [ 2.349945] usbcore: registered new interface driver usbtest [ 2.359313] mousedev: PS/2 mouse device common for all mice [ 2.366790] twl4030_keypad 48070000.i2c:twl@48:keypad: OF: linux,keymap property not defined in /ocp/i2c@48070000/twl@48/keypad [ 2.378967] twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap [ 2.386596] twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -2 [ 2.399047] input: twl4030_pwrbutton as /devices/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:pwrbutton/input/input1 [ 2.415496] twl_rtc 48070000.i2c:twl@48:rtc: Power up reset detected. [ 2.422576] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC [ 2.433685] twl_rtc 48070000.i2c:twl@48:rtc: rtc core: registered 48070000.i2c:twl@48 as rtc0 [ 2.444122] i2c /dev entries driver [ 2.451171] Driver for 1-wire Dallas network protocol. [ 2.461059] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.472930] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.482666] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.534637] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.544342] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.554809] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 [ 2.562347] platform 480b4000.mmc: Driver omap_hsmmc requests probe deferral [ 2.571197] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/ledb[0]' - status (0) [ 2.580780] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/ledb[0]' - status (0) [ 2.597656] ledtrig-cpu: registered to indicate activity on CPUs [ 2.605285] usbcore: registered new interface driver usbhid [ 2.611175] usbhid: USB HID core driver [ 2.617950] oprofile: using arm/armv7 [ 2.622680] TCP: cubic registered [ 2.626312] Initializing XFRM netlink socket [ 2.631317] NET: Registered protocol family 10 [ 2.640960] sit: IPv6 over IPv4 tunneling driver [ 2.648925] NET: Registered protocol family 17 [ 2.653747] NET: Registered protocol family 15 [ 2.658966] Key type dns_resolver registered [ 2.663879] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iva [ 2.671569] omap2_set_init_voltage: unable to set vdd_mpu_iva [ 2.677673] omap2_set_init_voltage: unable to find boot up OPP for vdd_core [ 2.685028] omap2_set_init_voltage: unable to set vdd_core [ 2.695770] ThumbEE CPU extension supported. [ 2.700317] Registering SWP/SWPB emulation handler [ 2.705474] SmartReflex Class3 initialized [ 2.720428] of_get_named_gpiod_flags: parsed 'gpio' property of node '/wl12xx_vmmc[0]' - status (0) [ 2.731109] vwl1271: 1800 mV [ 2.734527] vwl1271: supplied by VMMC2 [ 2.740173] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.749908] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.888854] twl_rtc 48070000.i2c:twl@48:rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.898956] sr_init: No PMIC hook to init smartreflex [ 2.904937] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 2.914093] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 3.009094] smsc911x 2c000000.ethernet eth0: SMSC911x/921x identified at 0xd087c000, IRQ: 208 [ 3.018585] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.884155] mmc0: card never left busy state [ 4.888671] mmc0: error -110 whilst initialising SD card [ 5.264251] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.285614] Sending DHCP requests ., OK [ 5.304656] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.131 [ 5.313720] IP-Config: Complete: [ 5.317230] device=eth0, hwaddr=00:50:c2:7e:99:42, ipaddr=192.168.57.131, mask=255.255.255.0, gw=255.255.255.255 [ 5.328430] host=192.168.57.131, domain=example.org, nis-domain=(none) [ 5.335784] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.342559] nameserver0=192.168.57.1 [ 5.347381] vwl1271: disabling [ 5.351806] VUSB3V1: disabling [ 5.357757] lcd_3v3: disabling [ 5.389709] VFS: Mounted root (nfs filesystem) readonly on device 0:13. [ 5.399291] devtmpfs: mounted [ 5.403472] Freeing unused kernel memory: 420K (c0867000 - c08d0000) /bin/sh: 0: can't access tty; job control turned off #