U-Boot 1.1.4 (Mar 18 2007 - 12:22:00) OMAP2430C-GP revision 3, PRCM #5A TI 2430SDP 1.1 Version + mDDR (Boot NOR) DRAM: 128 MB Flash: 192 MB NAND:64 MB In: serial Out: serial Err: serial Hit any key to stop autoboot: 3  0 OMAP243X SDP # OMAP243X SDP # setenv bootargs console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh OMAP243X SDP # loady ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... CSending: uImage-dtb.omap2430-sdp Sending: Transfer complete dem - CRC mode, 5(SOH)/4681(STX)/0(CAN) packets, 3 retries ## Total Size = 0x0049255c = 4793692 Bytes OMAP243X SDP # bootm ## Booting image at 80000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4793628 Bytes = 4.6 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.0-rc1-103807-g1f074f9 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Fri Nov 21 11:14:26 MST 2014 [ 0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP2430 SDP [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 86800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 32512 [ 0.000000] free_area_init_node: node 0, pgdat c0974940, node_mem_map c7df1000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] HighMem zone: 1048574 pages exceeds freesize 0 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP2430 [ 0.000000] [ 0.000000] PERCPU: Embedded 11 pages/cpu @c7d91000 s14976 r8192 d21888 u45056 [ 0.000000] pcpu-alloc: s14976 r8192 d21888 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32256 [ 0.000000] Kernel command line: console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] allocated 260096 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 93856K/130048K available (6251K kernel code, 681K rwdata, 2320K rodata, 420K init, 8264K bss, 36192K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0866f54 (8572 kB) [ 0.000000] .init : 0xc0867000 - 0xc08d0000 ( 420 kB) [ 0.000000] .data : 0xc08d0000 - 0xc097a410 ( 682 kB) [ 0.000000] .bss : 0xc097a410 - 0xc118c468 (8265 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000061] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000579] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.002929] Console: colour dummy device 80x30 [ 0.003112] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.003143] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.003173] ... MAX_LOCK_DEPTH: 48 [ 0.003204] ... MAX_LOCKDEP_KEYS: 8191 [ 0.003204] ... CLASSHASH_SIZE: 4096 [ 0.003234] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.003265] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.003295] ... CHAINHASH_SIZE: 32768 [ 0.003326] memory used by lock dependency info: 5167 kB [ 0.003356] per task-struct memory footprint: 1152 bytes [ 0.003417] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816) [ 0.125183] pid_max: default: 32768 minimum: 301 [ 0.126373] Security Framework initialized [ 0.126953] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.127014] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.137298] Initializing cgroup subsys memory [ 0.137512] Initializing cgroup subsys devices [ 0.137847] Initializing cgroup subsys freezer [ 0.138122] Initializing cgroup subsys blkio [ 0.138427] Initializing cgroup subsys perf_event [ 0.138702] CPU: Testing write buffer coherency: ok [ 0.143463] missing device node for CPU 0 [ 0.143554] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366 [ 0.143829] Setting up static identity map for 0x805ec800 - 0x805ec870 [ 0.157531] Brought up 1 CPUs [ 0.157562] SMP: Total of 1 processors activated. [ 0.157592] CPU: All CPU(s) started in SVC mode. [ 0.169799] devtmpfs: initialized [ 0.177886] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 0.288696] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3) [ 0.320800] pinctrl core: initialized pinctrl subsystem [ 0.330841] regulator-dummy: no parameters [ 0.482513] NET: Registered protocol family 16 [ 0.504760] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.512207] cpuidle: using governor ladder [ 0.512298] cpuidle: using governor menu [ 0.584625] omap_gpio 4900c000.gpio: Could not get gpio dbck [ 0.588226] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.591522] OMAP GPIO hardware version 2.4 [ 0.594635] omap_gpio 4900e000.gpio: Could not get gpio dbck [ 0.596160] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.601409] omap_gpio 49010000.gpio: Could not get gpio dbck [ 0.602630] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.608062] omap_gpio 49012000.gpio: Could not get gpio dbck [ 0.609466] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.614898] omap_gpio 480b6000.gpio: Could not get gpio dbck [ 0.616302] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.621856] omap-gpmc 6e000000.gpmc: GPMC revision 3.0 [ 0.623168] omap-gpmc 6e000000.gpmc: ethernet using bootloader timings on CS5 [ 0.638092] No ATAGs? [ 0.638275] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.638336] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.644989] OMAP DMA hardware revision 4.0 [ 0.722473] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.722686] edma-dma-engine: probe of edma-dma-engine.0 failed with error -22 [ 0.853820] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.867614] SCSI subsystem initialized [ 0.870147] usbcore: registered new interface driver usbfs [ 0.870727] usbcore: registered new interface driver hub [ 0.871154] usbcore: registered new device driver usb [ 0.881195] omap_i2c 48070000.i2c: bus 0 rev3.3 at 100 kHz [ 0.894989] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz [ 0.911315] Switched to clocksource 32k_counter [ 1.427246] NET: Registered protocol family 2 [ 1.433563] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.434082] TCP bind hash table entries: 1024 (order: 3, 36864 bytes) [ 1.435485] TCP: Hash tables configured (established 1024 bind 1024) [ 1.435974] TCP: reno registered [ 1.436096] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.436859] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.441253] NET: Registered protocol family 1 [ 1.446289] RPC: Registered named UNIX socket transport module. [ 1.446350] RPC: Registered udp transport module. [ 1.446411] RPC: Registered tcp transport module. [ 1.446441] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.451019] hw perfevents: enabled with armv6_1136 PMU driver, 3 counters available [ 1.469635] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.470306] audit: initializing netlink subsys (disabled) [ 1.471160] audit: type=2000 audit(1.460:1): initialized [ 1.485809] VFS: Disk quotas dquot_6.5.2 [ 1.486267] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.494873] NFS: Registering the id_resolver key type [ 1.496276] Key type id_resolver registered [ 1.496337] Key type id_legacy registered [ 1.497039] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.504364] msgmni has been set to 215 [ 1.518280] io scheduler noop registered [ 1.518371] io scheduler deadline registered [ 1.518646] io scheduler cfq registered (default) [ 1.529418] pinctrl-single 49002030.pinmux: 340 pins at pa fb002030 size 340 [ 1.539520] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV [ 1.545776] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.566894] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.566986] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 1.568603] omap_uart 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 29, base_baud = 3000000) is a OMAP UART0 [ 2.446441] console [ttyO0] enabled [ 2.457305] omap_uart 4806c000.serial: no wakeirq for uart0 [ 2.463439] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 2.474304] omap_uart 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 30, base_baud = 3000000) is a OMAP UART1 [ 2.489044] omap_uart 4806e000.serial: no wakeirq for uart0 [ 2.495147] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 2.505950] omap_uart 4806e000.serial: ttyO2 at MMIO 0x4806e000 (irq = 31, base_baud = 3000000) is a OMAP UART2 [ 2.525695] omap_rng 480a0000.rng: OMAP Random Number Generator ver. 50 [ 2.612060] brd: module loaded [ 2.662658] loop: module loaded [ 2.703857] twl 1-0048: PIH (irq 216) chaining IRQs 217..225 [ 2.711395] twl 1-0048: power (irq 222) chaining IRQs 225..232 [ 2.735107] VAUX1: at 3000 mV [ 2.747009] VAUX2_4030: at 2800 mV [ 2.758514] VAUX3: at 2800 mV [ 2.769897] VAUX4: at 1200 mV [ 2.781311] VDD1: 600 <--> 1450 mV at 1300 mV [ 2.793945] VDAC: 1800 mV [ 2.808135] VIO: at 1800 mV [ 2.820312] VINTANA1: 1500 mV [ 2.832641] VINTANA2: at 2750 mV [ 2.845184] VINTDIG: 1500 mV [ 2.855255] VMMC1: 1850 <--> 3150 mV at 1850 mV [ 2.868164] VMMC2: 1850 <--> 3150 mV at 2600 mV [ 2.879791] VUSB1V5: 1500 mV [ 2.888244] VUSB1V8: 1800 mV [ 2.897064] VUSB3V1: 3100 mV [ 2.909240] VPLL1: at 1300 mV [ 2.923065] VPLL2: 1800 mV [ 2.934143] VSIM: 1800 <--> 3000 mV at 1800 mV [ 2.945739] twl4030_gpio twl4030-gpio: gpio (irq 217) chaining IRQs 233..250 [ 2.955718] gpiochip_find_base: found new base at 494 [ 2.963195] gpiochip_add: registered GPIOs 494 to 511 on device: twl4030 [ 2.999603] mtdoops: mtd device (mtddev=name/number) must be supplied [ 3.025177] smc91x 8000300.ethernet (unnamed net_device) (uninitialized): smc91x: IOADDR c887a300 doesn't match configuration (0). [ 3.037719] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre [ 3.052642] smc91x 8000300.ethernet eth0: SMC91C94 (rev 9) at c887a300 IRQ 197 [ 3.060272] [ 3.062042] smc91x 8000300.ethernet eth0: Ethernet addr: 10:03:31:33:16:8f [ 3.075042] usbcore: registered new interface driver asix [ 3.081512] usbcore: registered new interface driver ax88179_178a [ 3.088378] usbcore: registered new interface driver cdc_ether [ 3.095367] usbcore: registered new interface driver smsc95xx [ 3.102050] usbcore: registered new interface driver net1080 [ 3.108459] usbcore: registered new interface driver cdc_subset [ 3.115325] usbcore: registered new interface driver zaurus [ 3.122161] usbcore: registered new interface driver cdc_ncm [ 3.132751] usbcore: registered new interface driver cdc_wdm [ 3.139404] usbcore: registered new interface driver usb-storage [ 3.146575] usbcore: registered new interface driver usbtest [ 3.160125] mousedev: PS/2 mouse device common for all mice [ 3.169311] twl4030_keypad 48072000.i2c:twl@48:keypad: OF: linux,keymap property not defined in /ocp/i2c@48072000/twl@48/keypad [ 3.181610] twl4030_keypad 48072000.i2c:twl@48:keypad: Failed to build keymap [ 3.189361] twl4030_keypad: probe of 48072000.i2c:twl@48:keypad failed with error -2 [ 3.208831] input: twl4030_pwrbutton as /devices/ocp/48072000.i2c/i2c-1/1-0048/48072000.i2c:twl@48:pwrbutton/input/input1 [ 3.229675] twl_rtc 48072000.i2c:twl@48:rtc: Power up reset detected. [ 3.237426] twl_rtc 48072000.i2c:twl@48:rtc: Enabling TWL-RTC [ 3.259185] twl_rtc 48072000.i2c:twl@48:rtc: rtc core: registered 48072000.i2c:twl@48 as rtc0 [ 3.272308] i2c /dev entries driver [ 3.282989] Driver for 1-wire Dallas network protocol. [ 3.305114] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.314941] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.381652] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.391479] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.402587] 480b4000.mmc supply vmmc not found, using dummy regulator [ 3.410552] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.418914] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.463775] ledtrig-cpu: registered to indicate activity on CPUs [ 3.472167] usbcore: registered new interface driver usbhid [ 3.478057] usbhid: USB HID core driver [ 3.487731] oprofile: using arm/armv6 [ 3.494110] TCP: cubic registered [ 3.497741] Initializing XFRM netlink socket [ 3.503662] NET: Registered protocol family 10 [ 3.519561] sit: IPv6 over IPv4 tunneling driver [ 3.532196] NET: Registered protocol family 17 [ 3.537170] NET: Registered protocol family 15 [ 3.543151] Key type dns_resolver registered [ 3.548370] SmartReflex Class3 initialized [ 3.585906] twl_rtc 48072000.i2c:twl@48:rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.596130] sr_init: No PMIC hook to init smartreflex [ 3.602447] sr_init: platform driver register failed for SR [ 3.736022] VUSB3V1: disabling [ 3.742156] VUSB1V8: disabling [ 3.748229] VUSB1V5: disabling [ 3.772247] Waiting for root device /dev/mmcblk0p1...