U-Boot SPL 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) OMAP5432 ES2.0 U-Boot 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) CPU : OMAP5432 ES2.0 Board: CM-T54 I2C: ready DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 3  2  0 CM-T54 # CM-T54 # setenv bootargs 'console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh' CM-T54 # loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 115200 bps... CSending: uImage-dtb.omap5-sbc-t54 Sending: Transfer complete m - CRC mode, 9(SOH)/4691(STX)/0(CAN) packets, 3 retries ## Total Size = 0x00494f50 = 4804432 Bytes CM-T54 # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4804368 Bytes = 4.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.0-rc1-103807-g1f074f9 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Fri Nov 21 11:14:26 MST 2014 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: CompuLab CM-T54 on SB-T54 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at fe800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524031 [ 0.000000] free_area_init_node: node 0, pgdat c0974940, node_mem_map ee7f9000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2576 pages used for memmap [ 0.000000] HighMem zone: 329471 pages, LIFO batch:31 [ 0.000000] OMAP5432 ES2.0 [ 0.000000] PERCPU: Embedded 11 pages/cpu @ee790000 s14976 r8192 d21888 u45056 [ 0.000000] pcpu-alloc: s14976 r8192 d21888 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522511 [ 0.000000] Kernel command line: console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 4194296 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 2040028K/2096124K available (6251K kernel code, 681K rwdata, 2320K rodata, 420K init, 8264K bss, 56096K reserved, 1301500K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0866f54 (8572 kB) [ 0.000000] .init : 0xc0867000 - 0xc08d0000 ( 420 kB) [ 0.000000] .data : 0xc08d0000 - 0xc097a410 ( 682 kB) [ 0.000000] .bss : 0xc097a410 - 0xc118c468 (8265 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001342] Console: colour dummy device 80x30 [ 0.001403] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001403] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001403] ... MAX_LOCK_DEPTH: 48 [ 0.001403] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001403] ... CLASSHASH_SIZE: 4096 [ 0.001434] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001434] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001434] ... CHAINHASH_SIZE: 32768 [ 0.001434] memory used by lock dependency info: 5167 kB [ 0.001434] per task-struct memory footprint: 1152 bytes [ 0.001464] Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896) [ 0.060455] pid_max: default: 32768 minimum: 301 [ 0.060729] Security Framework initialized [ 0.060882] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.060882] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.062774] Initializing cgroup subsys memory [ 0.062805] Initializing cgroup subsys devices [ 0.062866] Initializing cgroup subsys freezer [ 0.062927] Initializing cgroup subsys blkio [ 0.062957] Initializing cgroup subsys perf_event [ 0.063018] CPU: Testing write buffer coherency: ok [ 0.063812] /cpus/cpu@0 missing clock-frequency property [ 0.063842] /cpus/cpu@1 missing clock-frequency property [ 0.063842] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.063903] Setting up static identity map for 0x805ec800 - 0x805ec870 [ 0.067840] CPU1: Booted secondary processor [ 0.120544] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.121002] Brought up 2 CPUs [ 0.121032] SMP: Total of 2 processors activated. [ 0.121032] CPU: All CPU(s) started in SVC mode. [ 0.122955] devtmpfs: initialized [ 0.132568] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.133880] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.135070] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.257873] pinctrl core: initialized pinctrl subsystem [ 0.259582] regulator-dummy: no parameters [ 0.298889] NET: Registered protocol family 16 [ 0.302276] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.331024] cpuidle: using governor ladder [ 0.360992] cpuidle: using governor menu [ 0.368408] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.369079] OMAP GPIO hardware version 0.1 [ 0.369903] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.371246] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.372589] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.373901] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.375213] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.376556] gpiochip_add: registered GPIOs 192 to 223 on device: gpio [ 0.377838] gpiochip_add: registered GPIOs 224 to 255 on device: gpio [ 0.378784] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc' [ 0.378967] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 0.378967] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.379058] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.402069] No ATAGs? [ 0.402130] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.402160] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.403961] OMAP DMA hardware revision 0.0 [ 0.445556] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.445587] edma-dma-engine: probe of edma-dma-engine.0 failed with error -22 [ 0.471374] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.472015] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixed-regulator-mmcsd[0]' [ 0.472381] vmmcsd_fixed: 3300 mV [ 0.472656] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 0.473022] vwlan_pdn_fixed: 3300 mV [ 0.473114] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 0.474426] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 0.474456] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 0.474578] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 0.474853] vwlan_fixed: 3300 mV [ 0.474945] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 0.475219] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 0.475250] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 0.475341] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/ads7846-reg[0]' [ 0.475585] ads7846-reg: 3300 mV [ 0.478790] SCSI subsystem initialized [ 0.479278] usbcore: registered new interface driver usbfs [ 0.479400] usbcore: registered new interface driver hub [ 0.479522] usbcore: registered new device driver usb [ 0.479827] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0) [ 0.479858] hsusb2_phy supply vcc not found, using dummy regulator [ 0.480285] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb3_phy[0]' - status (0) [ 0.480316] hsusb3_phy supply vcc not found, using dummy regulator [ 0.480957] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c1_pins, deferring probe [ 0.480987] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 0.481018] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c2_pins, deferring probe [ 0.481048] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 0.481903] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 0.482055] omap_i2c 4807a000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c4_pins, deferring probe [ 0.482055] platform 4807a000.i2c: Driver omap_i2c requests probe deferral [ 0.482604] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 100 kHz [ 0.485565] Switched to clocksource 32k_counter [ 0.586883] NET: Registered protocol family 2 [ 0.588012] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.588195] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.590515] TCP: Hash tables configured (established 8192 bind 8192) [ 0.590637] TCP: reno registered [ 0.590667] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.590972] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.591979] NET: Registered protocol family 1 [ 0.592681] RPC: Registered named UNIX socket transport module. [ 0.592681] RPC: Registered udp transport module. [ 0.592681] RPC: Registered tcp transport module. [ 0.592681] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.593536] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.597595] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.597839] audit: initializing netlink subsys (disabled) [ 0.597930] audit: type=2000 audit(0.580:1): initialized [ 0.600555] VFS: Disk quotas dquot_6.5.2 [ 0.600677] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.602081] NFS: Registering the id_resolver key type [ 0.602294] Key type id_resolver registered [ 0.602294] Key type id_legacy registered [ 0.602416] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.603485] msgmni has been set to 1442 [ 0.605743] bounce: pool size: 64 pages [ 0.605804] io scheduler noop registered [ 0.605804] io scheduler deadline registered [ 0.605865] io scheduler cfq registered (default) [ 0.611114] pinctrl-single 4a002840.pinmux: 219 pins at pa fc002840 size 438 [ 0.611450] pinctrl-single 4ae0c840.pinmux: 28 pins at pa fce0c840 size 56 [ 0.613891] pbias_mmc_omap5: 1800 <--> 3000 mV at 3000 mV [ 0.614990] abb_mpu: 1060 <--> 1250 mV [ 0.615631] abb_mm: 1025 <--> 1120 mV [ 0.616699] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.620727] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.620758] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.621032] omap_uart 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 104, base_baud = 3000000) is a OMAP UART0 [ 0.622070] omap_uart 4806c000.serial: no wakeirq for uart0 [ 0.622070] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 0.622253] omap_uart 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 105, base_baud = 3000000) is a OMAP UART1 [ 0.622985] omap_uart 48020000.serial: no wakeirq for uart0 [ 0.623016] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48020000[0]' [ 0.623168] omap_uart 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 106, base_baud = 3000000) is a OMAP UART2 [ 0.623901] omap_uart 4806e000.serial: no wakeirq for uart0 [ 0.623931] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 0.624084] omap_uart 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 102, base_baud = 3000000) is a OMAP UART3 [ 1.768310] console [ttyO3] enabled [ 1.772888] omap_uart 48066000.serial: no wakeirq for uart0 [ 1.778747] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48066000[0]' [ 1.788818] omap_uart 48066000.serial: ttyO4 at MMIO 0x48066000 (irq = 137, base_baud = 3000000) is a OMAP UART4 [ 1.800292] omap_uart 48068000.serial: no wakeirq for uart0 [ 1.806121] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48068000[0]' [ 1.816131] omap_uart 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 138, base_baud = 3000000) is a OMAP UART5 [ 1.843261] brd: module loaded [ 1.855316] loop: module loaded [ 1.860717] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.874664] usbcore: registered new interface driver asix [ 1.880401] usbcore: registered new interface driver ax88179_178a [ 1.886871] usbcore: registered new interface driver cdc_ether [ 1.893096] usbcore: registered new interface driver smsc95xx [ 1.899169] usbcore: registered new interface driver net1080 [ 1.905181] usbcore: registered new interface driver cdc_subset [ 1.911468] usbcore: registered new interface driver zaurus [ 1.917419] usbcore: registered new interface driver cdc_ncm [ 1.923889] usbcore: registered new interface driver cdc_wdm [ 1.929962] usbcore: registered new interface driver usb-storage [ 1.936370] usbcore: registered new interface driver usbtest [ 1.943695] mousedev: PS/2 mouse device common for all mice [ 1.951477] i2c /dev entries driver [ 1.956359] Driver for 1-wire Dallas network protocol. [ 1.962432] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported [ 1.969757] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported [ 1.977081] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported [ 1.986755] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.995300] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.005584] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.016265] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.023345] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.030853] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.040405] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.095764] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.105316] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.115081] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.122009] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.129913] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led@1[0]' - status (0) [ 2.139404] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led@1[0]' - status (0) [ 2.149566] ledtrig-cpu: registered to indicate activity on CPUs [ 2.156188] usbcore: registered new interface driver usbhid [ 2.158752] mmc0: BKOPS_EN bit is not set [ 2.160766] mmc0: new high speed MMC card at address 0001 [ 2.162139] mmcblk0: mmc0:0001 SEM08G 7.28 GiB [ 2.166290] mmcblk0boot0: mmc0:0001 SEM08G partition 1 2.00 MiB [ 2.166595] mmcblk0boot1: mmc0:0001 SEM08G partition 2 2.00 MiB [ 2.188934] usbhid: USB HID core driver [ 2.194641] oprofile: using timer interrupt. [ 2.199462] TCP: cubic registered [ 2.202941] Initializing XFRM netlink socket [ 2.207641] NET: Registered protocol family 10 [ 2.213989] sit: IPv6 over IPv4 tunneling driver [ 2.215637] mmcblk0: unknown partition table [ 2.224792] NET: Registered protocol family 17 [ 2.229492] NET: Registered protocol family 15 [ 2.234313] Key type dns_resolver registered [ 2.238952] omap_vc_init_channel: No PMIC info for vdd_core [ 2.244781] omap_vp_init: No PMIC info for vdd_core [ 2.249877] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.255523] omap_vp_init: No PMIC info for vdd_mm [ 2.260437] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.266174] omap_vp_init: No PMIC info for vdd_mpu [ 2.271789] Power Management for TI OMAP4+ devices. [ 2.277130] ThumbEE CPU extension supported. [ 2.281707] Registering SWP/SWPB emulation handler [ 2.286865] SmartReflex Class3 initialized [ 2.294036] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.305664] vwlan_pdn_fixed: 3300 mV [ 2.309661] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 2.318389] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 2.327392] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 2.337158] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.348083] vwlan_fixed: 3300 mV [ 2.351715] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 2.359802] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 2.368408] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 2.381805] palmas 0-0048: Irq flag is 0x00000000 [ 2.392974] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.440551] smps123: 600 <--> 1500 mV at 1060 mV [ 2.447998] smps45: 600 <--> 1310 mV at 1030 mV [ 2.455291] smps6: 1500 mV [ 2.460601] smps7: 1800 mV [ 2.466217] smps8: 600 <--> 1310 mV at 1040 mV [ 2.474639] smps9: 3300 mV [ 2.479339] smps10_out2: 5000 mV [ 2.484344] smps10_out1: 5000 mV [ 2.488922] ldo1: 1500 <--> 1800 mV [ 2.495147] ldo2: 3300 mV [ 2.500488] ldo3: 1500 mV [ 2.504791] ldo4: 1500 <--> 1800 mV [ 2.511016] ldo5: 1800 mV [ 2.517791] ldo6: 1200 mV [ 2.523071] ldo7: 2000 mV [ 2.528411] ldo8: 3000 mV [ 2.533721] ldo9: 1800 <--> 3000 mV at 900 mV [ 2.540893] ldoln: 1800 mV [ 2.546356] ldousb: 3250 mV [ 2.550659] REGEN1: no parameters [ 2.554626] REGEN2: no parameters [ 2.558929] regen3: no parameters [ 2.563323] SYSEN1: no parameters [ 2.567352] SYSEN2: no parameters [ 2.571136] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.578826] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz [ 2.586822] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 2.593231] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.603790] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.656066] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.665863] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.675933] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.683074] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.690795] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.702117] vwlan_pdn_fixed: 3300 mV [ 2.706146] vwlan_pdn_fixed: supplied by ldo2 [ 2.711273] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.722198] vwlan_fixed: 3300 mV [ 2.725830] vwlan_fixed: supplied by vwlan_pdn_fixed [ 2.731719] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.741516] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.745819] mmc1: new high speed SDHC card at address 0002 [ 2.755706] mmcblk1: mmc1:0002 00000 3.66 GiB [ 2.757720] mmcblk1: p1 p2 [ 2.806945] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.813598] sr_init: No PMIC hook to init smartreflex [ 2.819183] sr_init: platform driver register failed for SR [ 2.839782] mmc2: new high speed SDIO card at address 0001 [ 2.858306] ads7846-reg: disabling [ 2.869232] kjournald starting. Commit interval 5 seconds [ 2.869384] EXT3-fs (mmcblk1p2): mounted filesystem with ordered data mode [ 2.869476] VFS: Mounted root (ext3 filesystem) readonly on device 179:26. [ 2.891632] devtmpfs: mounted [ 2.895172] Freeing unused kernel memory: 420K (c0867000 - c08d0000) /bin/sh: can't access tty; job control turned off / # / # / #