CCSending /srv/serial/u-boot-spl.bin, 784 blocks: Give your local XMODEM receive command now. Transfer complete t SPL 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 CSending: u-boot.bin Sending: Transfer complete - CRC mode, 3(SOH)/375(STX)/0(CAN) packets, 3 retries Loaded 384084 bytes U-Boot 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 mmc_send_cmd : timeout: No status update Card did not respond to voltage select! mmc0(part 0) is current device mmc_send_cmd : timeout: No status update Card did not respond to voltage select! Booting from nand ... no devices available Wrong Image Format for bootm command ERROR: can't get kernel image! U-Boot# a askenv - get environment variables from stdin Usage: askenv name [message] [size] - get environment variable 'name' from stdin (max 'size' chars) U-Boot# setenv autoload off; setenv serverip 192.168.57.1; dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.138 U-Boot# tftp 0x81000000 zImage.omap2plus_defconfig link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'zImage.omap2plus_defconfig'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ####################################### 939.5 KiB/s done Bytes transferred = 3429744 (345570 hex) U-Boot# tftp 0x82000000 am335x-bone.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'am335x-bone.dtb'. Load address: 0x82000000 Loading: *### 899.4 KiB/s done Bytes transferred = 29489 (7331 hex) U-Boot# setenv bootargs console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp U-Boot# U-Boot# bootz 0x81000000 - 0x82000000 ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 82000000, end 8200a330 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.1.0-rc1-142160-ga5bf00c (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Fri May 8 13:11:26 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] earlycon: no match for ttyO0,115200n8 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c0958800, node_mem_map cfcb1000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 13 pages/cpu @cfc5c000 s22976 r8192 d22080 u53248 [ 0.000000] pcpu-alloc: s22976 r8192 d22080 u53248 alloc=13*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64704 [ 0.000000] Kernel command line: console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 224000K/261120K available (6211K kernel code, 739K rwdata, 2168K rodata, 440K init, 8220K bss, 20736K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc083706c (8381 kB) [ 0.000000] .init : 0xc0838000 - 0xc08a6000 ( 440 kB) [ 0.000000] .data : 0xc08a6000 - 0xc095ee58 ( 740 kB) [ 0.000000] .bss : 0xc0961000 - 0xc11683d0 (8221 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000021] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000058] clocksource timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000128] OMAP clocksource: timer1 at 24000000 Hz [ 0.001523] Console: colour dummy device 80x30 [ 0.001616] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001632] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001645] ... MAX_LOCK_DEPTH: 48 [ 0.001659] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001672] ... CLASSHASH_SIZE: 4096 [ 0.001685] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001698] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001711] ... CHAINHASH_SIZE: 32768 [ 0.001724] memory used by lock dependency info: 5167 kB [ 0.001739] per task-struct memory footprint: 1152 bytes [ 0.001777] Calibrating delay loop... 545.58 BogoMIPS (lpj=2727936) [ 0.098008] pid_max: default: 32768 minimum: 301 [ 0.098618] Security Framework initialized [ 0.098898] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.098925] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.103926] Initializing cgroup subsys blkio [ 0.103992] Initializing cgroup subsys memory [ 0.104144] Initializing cgroup subsys devices [ 0.104303] Initializing cgroup subsys freezer [ 0.104512] Initializing cgroup subsys perf_event [ 0.104629] CPU: Testing write buffer coherency: ok [ 0.106941] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.107120] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.114264] Brought up 1 CPUs [ 0.114303] SMP: Total of 1 processors activated (545.58 BogoMIPS). [ 0.114320] CPU: All CPU(s) started in SVC mode. [ 0.120250] devtmpfs: initialized [ 0.124030] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.195076] omap_hwmod: tptc0 using broken dt data from edma [ 0.195845] omap_hwmod: tptc1 using broken dt data from edma [ 0.196587] omap_hwmod: tptc2 using broken dt data from edma [ 0.209158] omap_hwmod: debugss: _wait_target_disable failed [ 0.268183] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.271823] pinctrl core: initialized pinctrl subsystem [ 0.329251] NET: Registered protocol family 16 [ 0.339805] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.343406] cpuidle: using governor ladder [ 0.343451] cpuidle: using governor menu [ 0.356743] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.358426] OMAP GPIO hardware version 0.1 [ 0.360627] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.364063] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.367318] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.389804] No ATAGs? [ 0.389853] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.462985] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.464174] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator@0[0]' [ 0.470033] SCSI subsystem initialized [ 0.471282] libata version 3.00 loaded. [ 0.473033] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.480302] Switched to clocksource timer1 [ 0.745225] NET: Registered protocol family 2 [ 0.748343] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.748611] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.749854] TCP: Hash tables configured (established 2048 bind 2048) [ 0.750414] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.750765] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.752427] NET: Registered protocol family 1 [ 0.755209] RPC: Registered named UNIX socket transport module. [ 0.755245] RPC: Registered udp transport module. [ 0.755262] RPC: Registered tcp transport module. [ 0.755279] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.758398] CPU PMU: Failed to parse /interrupt-affinity[0] [ 0.758598] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.766044] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.766534] audit: initializing netlink subsys (disabled) [ 0.766950] audit: type=2000 audit(0.760:1): initialized [ 0.774640] VFS: Disk quotas dquot_6.6.0 [ 0.774873] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.778887] NFS: Registering the id_resolver key type [ 0.779563] Key type id_resolver registered [ 0.779588] Key type id_legacy registered [ 0.779882] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.788513] io scheduler noop registered [ 0.788561] io scheduler deadline registered [ 0.788644] io scheduler cfq registered (default) [ 0.791992] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.795865] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.806140] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.806186] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@44e09000[0]' [ 0.807165] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 154, base_baud = 3000000) is a OMAP UART0 [ 1.608466] console [ttyO0] enabled [ 1.664352] brd: module loaded [ 1.698847] loop: module loaded [ 1.706074] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.721917] mousedev: PS/2 mouse device common for all mice [ 1.727804] i2c /dev entries driver [ 1.733885] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 1.740331] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.747231] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.757735] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.762655] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 1.768960] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.775860] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 1.785485] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 1.795014] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 1.802310] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 1.809843] omap_hsmmc 48060000.mmc: unable to get vmmc regulator -517 [ 1.818311] ledtrig-cpu: registered to indicate activity on CPUs [ 1.826590] oprofile: using arm/armv7 [ 1.831763] Initializing XFRM netlink socket [ 1.836485] NET: Registered protocol family 17 [ 1.841398] NET: Registered protocol family 15 [ 1.846659] Key type dns_resolver registered [ 1.851596] omap_voltage_late_init: Voltage driver support not added [ 1.858284] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize [ 1.866836] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize [ 1.877124] ThumbEE CPU extension supported. [ 1.881778] Registering SWP/SWPB emulation handler [ 1.886823] SmartReflex Class3 initialized [ 1.955774] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 1.961657] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 1.969170] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 1.975589] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.982545] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.993062] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.997926] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 2.004301] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 2.011204] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 2.020824] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 2.030348] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 2.037402] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 2.160154] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.166575] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.179561] libphy: 4a101000.mdio: probed [ 2.183985] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.195705] cpsw 4a100000.ethernet: Detected MACID = 78:c5:e5:c3:1e:2a [ 2.207327] hctosys: unable to open rtc device (rtc0) [ 2.212799] sr_init: No PMIC hook to init smartreflex [ 2.218502] sr_init: platform driver register failed for SR [ 2.260699] net eth0: initializing cpsw version 1.12 (0) [ 2.269083] net eth0: phy found : id is : 0x7c0f1 [ 2.274321] libphy: PHY 4a101000.mdio:01 not found [ 2.279359] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 5.340800] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 5.370139] Sending DHCP requests ., OK [ 5.390697] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.138 [ 5.399866] IP-Config: Complete: [ 5.403406] device=eth0, hwaddr=78:c5:e5:c3:1e:2a, ipaddr=192.168.57.138, mask=255.255.255.0, gw=255.255.255.255 [ 5.414577] host=192.168.57.138, domain=example.org, nis-domain=(none) [ 5.421915] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.428667] nameserver0=192.168.57.1 [ 5.433395] vmmcsd_fixed: disabling [ 5.469741] VFS: Mounted root (nfs filesystem) on device 0:15. [ 5.479129] devtmpfs: mounted [ 5.483693] Freeing unused kernel memory: 440K (c0838000 - c08a6000) INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.764625] udevd[142]: starting version 175 [ ok . [....] Synthesizing the initial hotplug events...udevd[171]: error changing net interface name eth0 to eth4: Device or resource busy [ ok done. [....] Waiting for /dev to be fully populated...[ ok done. [....] Activating swap...[ ok [ 17.427195] random: nonblocking pool is initialized done. [....] Cleaning up temporary files... /tmp[ ok . [....] Activating lvm and md swap...[ ok done. [....] Checking file systems...fsck from util-linux 2.20.1 [ ok done. [....] Mounting local filesystems...[ ok done. [....] Activating swapfile swap...[ ok done. [....] Cleaning up temporary files...[ ok . [....] Setting kernel variables ...[ ok done. [....] Configuring network interfaces...[ ok done. [....] Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 [ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [....] Cleaning up temporary files...[ ok . [....] Starting network benchmark server[ ok . INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting network benchmark server[FAIL failed! [....] Starting system message bus: dbus[ ok . [....] Starting rpcbind daemon...[....] Already running.[ ok . [....] Starting NFS common utilities: statd idmapd[ ok . Debian GNU/Linux wheezy/sid armel ttyO0 armel login: