usb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: cpsw, usb_ether Hit any key to stop autoboot: 1  0 U-Boot# U-Boot# ver U-Boot 2013.01-00161-g6e787b7 (Feb 06 2013 - 15:10:23) arm-none-eabi-gcc (Sourcery G++ Lite 2011.03-42) 4.5.2 GNU ld (Sourcery G++ Lite 2011.03-42) 2.20.51.20100809 U-Boot# setenv bootargs console=ttyO0,115200n8 debug ignore_loglevel earlyprintk=serial init=/bin/sh mem=128M root=/dev/ram rw initrd=0x82000000,16MB ramdisk_size=65536 U-Boot# U-Boot# setenv serverip 192.168.57.1 U-Boot# U-Boot# setenv bootfile uImage-dtb.am335x-bone U-Boot# U-Boot# dhcp 81000000 link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.137 Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.137 Filename 'uImage-dtb.am335x-bone'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ##################################### 641.6 KiB/s done Bytes transferred = 4350297 (426159 hex) U-Boot# mmc rescan 0 U-Boot# U-Boot# fatload mmc 0 82000000 ramdisk-pm.gz reading ramdisk-pm.gz 2022580 bytes read in 239 ms (8.1 MiB/s) U-Boot# U-Boot# bootm 81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4350233 Bytes = 4.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.0.0-rc1-129034-g82a17660 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Fri Apr 3 12:47:16 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x87000000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c0865dc0, node_mem_map c6ed1000 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 12 pages/cpu @c6ea7000 s18368 r8192 d22592 u49152 [ 0.000000] pcpu-alloc: s18368 r8192 d22592 u49152 alloc=12*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyO0,115200n8 debug ignore_loglevel earlyprintk=serial init=/bin/sh mem=128M root=/dev/ram rw initrd=0x82000000,16MB ramdisk_size=65536 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 79976K/131072K available (5774K kernel code, 335K rwdata, 2124K rodata, 356K init, 8216K bss, 34712K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07becc4 (7900 kB) [ 0.000000] .init : 0xc07bf000 - 0xc0818000 ( 356 kB) [ 0.000000] .data : 0xc0818000 - 0xc086bc68 ( 336 kB) [ 0.000000] .bss : 0xc086bc68 - 0xc1071f10 (8217 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000024] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000100] OMAP clocksource: timer1 at 24000000 Hz [ 0.001404] Console: colour dummy device 80x30 [ 0.001485] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001502] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001516] ... MAX_LOCK_DEPTH: 48 [ 0.001529] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001542] ... CLASSHASH_SIZE: 4096 [ 0.001556] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001569] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001581] ... CHAINHASH_SIZE: 32768 [ 0.001595] memory used by lock dependency info: 5167 kB [ 0.001609] per task-struct memory footprint: 1152 bytes [ 0.001649] Calibrating delay loop... 548.04 BogoMIPS (lpj=2740224) [ 0.108282] pid_max: default: 32768 minimum: 301 [ 0.108822] Security Framework initialized [ 0.109098] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.109130] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.113781] Initializing cgroup subsys blkio [ 0.113849] Initializing cgroup subsys memory [ 0.114001] Initializing cgroup subsys devices [ 0.114153] Initializing cgroup subsys freezer [ 0.114347] Initializing cgroup subsys perf_event [ 0.114470] CPU: Testing write buffer coherency: ok [ 0.116528] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.116709] Setting up static identity map for 0x805792b8 - 0x80579328 [ 0.122267] Brought up 1 CPUs [ 0.122303] SMP: Total of 1 processors activated (548.04 BogoMIPS). [ 0.122320] CPU: All CPU(s) started in SVC mode. [ 0.126971] devtmpfs: initialized [ 0.131083] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.192663] omap_hwmod: tptc0 using broken dt data from edma [ 0.193318] omap_hwmod: tptc1 using broken dt data from edma [ 0.193942] omap_hwmod: tptc2 using broken dt data from edma [ 0.205307] omap_hwmod: debugss: _wait_target_disable failed [ 0.267405] pinctrl core: initialized pinctrl subsystem [ 0.321730] NET: Registered protocol family 16 [ 0.333967] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.337320] cpuidle: using governor ladder [ 0.337363] cpuidle: using governor menu [ 0.348794] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.350188] OMAP GPIO hardware version 0.1 [ 0.352113] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.355120] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.358023] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.376616] No ATAGs? [ 0.376665] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.442808] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.443964] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator@0[0]' [ 0.449548] SCSI subsystem initialized [ 0.450678] libata version 3.00 loaded. [ 0.452270] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 0.452331] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.459317] Switched to clocksource timer1 [ 0.686611] NET: Registered protocol family 2 [ 0.689732] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.689979] TCP bind hash table entries: 1024 (order: 3, 36864 bytes) [ 0.690610] TCP: Hash tables configured (established 1024 bind 1024) [ 0.690887] TCP: reno registered [ 0.690933] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.691278] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.692912] NET: Registered protocol family 1 [ 0.695509] RPC: Registered named UNIX socket transport module. [ 0.695544] RPC: Registered udp transport module. [ 0.695561] RPC: Registered tcp transport module. [ 0.695578] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.697893] Trying to unpack rootfs image as initramfs... [ 0.700665] rootfs image is not initramfs (no cpio magic); looks like an initrd [ 0.909634] Freeing initrd memory: 16384K (c2000000 - c3000000) [ 0.910505] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.917199] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.917670] audit: initializing netlink subsys (disabled) [ 0.918078] audit: type=2000 audit(0.910:1): initialized [ 0.925361] VFS: Disk quotas dquot_6.5.2 [ 0.925609] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.929548] NFS: Registering the id_resolver key type [ 0.930089] Key type id_resolver registered [ 0.930113] Key type id_legacy registered [ 0.930407] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.937271] io scheduler noop registered [ 0.937317] io scheduler deadline registered [ 0.937400] io scheduler cfq registered (default) [ 0.940254] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.943693] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.953305] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.953364] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@44e09000[0]' [ 0.954166] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 154, base_baud = 3000000) is a OMAP UART0 [ 1.742990] console [ttyO0] enabled [ 1.794050] brd: module loaded [ 1.824862] loop: module loaded [ 1.831801] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.846307] mousedev: PS/2 mouse device common for all mice [ 1.852337] i2c /dev entries driver [ 1.856424] Driver 'mmcblk' needs updating - please use bus_type methods [ 1.865250] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 1.871680] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.878581] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.889073] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.893936] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 1.900294] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.907148] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 1.916772] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 1.926298] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 1.933547] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 1.941039] omap_hsmmc 48060000.mmc: unable to get vmmc regulator -517 [ 1.948962] platform 48060000.mmc: Driver omap_hsmmc requests probe deferral [ 1.956766] ledtrig-cpu: registered to indicate activity on CPUs [ 1.964558] oprofile: using arm/armv7 [ 1.969626] TCP: cubic registered [ 1.973171] Initializing XFRM netlink socket [ 1.977851] NET: Registered protocol family 17 [ 1.982751] NET: Registered protocol family 15 [ 1.987915] Key type dns_resolver registered [ 1.992902] omap_voltage_late_init: Voltage driver support not added [ 2.001214] ThumbEE CPU extension supported. [ 2.005777] Registering SWP/SWPB emulation handler [ 2.061396] tps65217 0-0024: TPS65217 ID 0xf version 1.1 [ 2.067116] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.074553] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 2.080980] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 2.087890] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 2.098389] omap_hsmmc 48060000.mmc: Got CD GPIO [ 2.103308] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 2.109652] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 2.116508] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 2.126126] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 2.135648] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 2.142733] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 2.247658] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.258891] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.265292] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.273873] mmc0: new high speed SDHC card at address 1234 [ 2.284510] mmcblk0: mmc0:1234 SA04G 3.63 GiB [ 2.293475] libphy: 4a101000.mdio: probed [ 2.297720] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.309989] cpsw 4a100000.ethernet: Detected MACID = d4:94:a1:90:76:28 [ 2.321218] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.359080] vmmcsd_fixed: disabling [ 2.369956] mmcblk0: p1 p2 [ 2.379362] RAMDISK: gzip image found at block 0 [ 2.889243] VFS: Mounted root (ext2 filesystem) on device 1:0. [ 2.896816] devtmpfs: mounted [ 2.901118] Freeing unused kernel memory: 356K (c07bf000 - c0818000) /bin/sh: can't access tty; job„þ/ # / # / #