怘€æ€˜€`3f<€fÀæøÀ̆ž?`?fófÏfÆž`??ð3ž<3ž<` 0x3e470000 [ 0.000000] L2C: DT/platform modifies aux control register: 0x0e070000 -> 0x3e470000 [ 0.000000] L2C-310 erratum 727915 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node dss_fck [ 0.000000] ti_dt_clocks_register: failed to lookup clock node dss_fck [ 0.000000] ti_dt_clocks_register: failed to lookup clock node div_ts_ck [ 0.000000] ti_dt_clocks_register: failed to lookup clock node bandgap_ts_fclk [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001129] Console: colour dummy device 80x30 [ 0.001190] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001190] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001190] ... MAX_LOCK_DEPTH: 48 [ 0.001190] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001220] ... CLASSHASH_SIZE: 4096 [ 0.001220] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001220] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001220] ... CHAINHASH_SIZE: 32768 [ 0.001220] memory used by lock dependency info: 5167 kB [ 0.001251] per task-struct memory footprint: 1536 bytes [ 0.001251] Calibrating delay loop... 2007.04 BogoMIPS (lpj=10035200) [ 0.119537] pid_max: default: 32768 minimum: 301 [ 0.119903] Security Framework initialized [ 0.119995] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.120025] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.122772] CPU: Testing write buffer coherency: ok [ 0.124114] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.124206] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.179534] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.179992] Brought up 2 CPUs [ 0.180023] SMP: Total of 2 processors activated (4014.08 BogoMIPS). [ 0.180023] CPU: All CPU(s) started in SVC mode. [ 0.182403] devtmpfs: initialized [ 0.222900] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1 [ 0.223632] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.226043] pinctrl core: initialized pinctrl subsystem [ 0.229980] NET: Registered protocol family 16 [ 0.234680] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.238525] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.241607] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.329986] omap_hwmod: l3_instr: _wait_target_disable failed [ 0.409667] cpuidle: using governor menu [ 0.419860] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio [ 0.420867] OMAP GPIO hardware version 0.1 [ 0.421783] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio [ 0.423370] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio [ 0.424926] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio [ 0.426452] gpiochip_add_data: registered GPIOs 128 to 159 on device: gpio [ 0.427978] gpiochip_add_data: registered GPIOs 160 to 191 on device: gpio [ 0.429382] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.429504] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.430328] irq: no irq domain found for /ocp/l4@4a000000/scm@100000/pinmux@40 ! [ 0.430786] irq: no irq domain found for /ocp/l4@4a000000/scm@100000/pinmux@40 ! [ 0.431243] irq: no irq domain found for /ocp/l4@4a000000/scm@100000/pinmux@40 ! [ 0.446533] platform 4b501000.aes: Cannot lookup hwmod 'aes' [ 0.446899] platform 480a5000.des: Cannot lookup hwmod 'des' [ 0.453338] No ATAGs? [ 0.453399] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.453430] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.455383] OMAP DMA hardware revision 0.0 [ 0.457061] ARM PMU: not yet supported on OMAP4430 due to missing CTI driver [ 0.501556] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.502929] of_get_named_gpiod_flags: parsed 'gpio' property of node '/hsusb1_power_reg[0]' - status (0) [ 0.579895] reg-fixed-voltage wl12xx_vmmc: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_wl12xx_gpio, deferring probe [ 0.583404] SCSI subsystem initialized [ 0.583953] libata version 3.00 loaded. [ 0.584533] usb_phy_generic hsusb1_phy: GPIO lookup for consumer reset [ 0.584564] usb_phy_generic hsusb1_phy: using device tree for GPIO lookup [ 0.584625] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb1_phy[0]' - status (0) [ 0.584686] no flags found for reset [ 0.584716] usb_phy_generic hsusb1_phy: GPIO lookup for consumer vbus-detect [ 0.584716] usb_phy_generic hsusb1_phy: using device tree for GPIO lookup [ 0.584716] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb1_phy[0]' [ 0.584747] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb1_phy[0]' [ 0.584747] usb_phy_generic hsusb1_phy: using lookup tables for GPIO lookup [ 0.584838] usb_phy_generic hsusb1_phy: lookup for GPIO vbus-detect failed [ 0.585754] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c1_pins, deferring probe [ 0.585845] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c2_pins, deferring probe [ 0.585906] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c3_pins, deferring probe [ 0.585968] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c4_pins, deferring probe [ 0.586242] pps_core: LinuxPPS API ver. 1 registered [ 0.586273] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.586303] PTP clock support registered [ 0.589324] clocksource: Switched to clocksource 32k_counter [ 0.669250] VFS: Disk quotas dquot_6.6.0 [ 0.669464] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.693908] NET: Registered protocol family 2 [ 0.695648] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.695739] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) [ 0.696624] TCP: Hash tables configured (established 4096 bind 4096) [ 0.696899] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.697021] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.697753] NET: Registered protocol family 1 [ 0.699066] RPC: Registered named UNIX socket transport module. [ 0.699096] RPC: Registered udp transport module. [ 0.699096] RPC: Registered tcp transport module. [ 0.699096] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.707855] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.708160] audit: initializing netlink subsys (disabled) [ 0.708374] audit: type=2000 audit(0.680:1): initialized [ 0.713775] NFS: Registering the id_resolver key type [ 0.714080] Key type id_resolver registered [ 0.714080] Key type id_legacy registered [ 0.714233] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.718200] io scheduler noop registered [ 0.718231] io scheduler deadline registered [ 0.718261] io scheduler cfq registered (default) [ 0.721832] pinctrl-single 4a100040.pinmux: 203 pins at pa fc100040 size 406 [ 0.722229] pinctrl-single 4a31e040.pinmux: 28 pins at pa fc31e040 size 56 [ 0.726959] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.731475] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.731506] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.731933] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 226, base_baud = 3000000) is a OMAP UART0 [ 0.733276] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 0.733489] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 227, base_baud = 3000000) is a OMAP UART1 [ 0.734313] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48020000[0]' [ 0.734497] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 228, base_baud = 3000000) is a OMAP UART2 [ 1.286407] console [ttyO2] enabled [ 1.289337] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 1.294616] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 229, base_baud = 3000000) is a OMAP UART3 [ 1.324218] brd: module loaded [ 1.342346] loop: module loaded [ 1.346710] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.360260] mousedev: PS/2 mouse device common for all mice [ 1.363281] i2c /dev entries driver [ 1.366363] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 1.369659] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.373199] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.378143] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.383026] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.386657] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 1.389831] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 1.393066] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.396606] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.401550] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.406433] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.410095] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 1.440612] omap_hsmmc 480d5000.mmc: GPIO lookup for consumer wp [ 1.443847] omap_hsmmc 480d5000.mmc: using device tree for GPIO lookup [ 1.447387] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480d5000[0]' [ 1.452362] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480d5000[0]' [ 1.457244] omap_hsmmc 480d5000.mmc: using lookup tables for GPIO lookup [ 1.460906] omap_hsmmc 480d5000.mmc: lookup for GPIO wp failed [ 1.489837] ledtrig-cpu: registered to indicate activity on CPUs [ 1.494079] oprofile: no performance counters [ 1.497406] oprofile: using timer interrupt. [ 1.500427] Initializing XFRM netlink socket [ 1.503082] NET: Registered protocol family 10 [ 1.507629] sit: IPv6 over IPv4 tunneling driver [ 1.511871] NET: Registered protocol family 17 [ 1.514343] NET: Registered protocol family 15 [ 1.516998] Key type dns_resolver registered [ 1.519622] twl: not initialized [ 1.521362] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 [ 1.525695] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 [ 1.530059] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 [ 1.534393] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 [ 1.538726] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 [ 1.543060] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660 [ 1.547393] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1410000 Vs max 1316660 [ 1.551757] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu [ 1.555450] omap2_set_init_voltage: unable to set vdd_mpu [ 1.558380] omap2_set_init_voltage: unable to find boot up OPP for vdd_core [ 1.562164] omap2_set_init_voltage: unable to set vdd_core [ 1.565155] omap2_set_init_voltage: unable to find boot up OPP for vdd_iva [ 1.568878] omap2_set_init_voltage: unable to set vdd_iva [ 1.573577] Power Management for TI OMAP4+ devices. [ 1.576202] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.580139] ThumbEE CPU extension supported. [ 1.580139] Registering SWP/SWPB emulation handler [ 1.580139] SmartReflex Class3 initialized [ 1.593048] of_get_named_gpiod_flags: parsed 'gpio' property of node '/wl12xx_vmmc[0]' - status (0) [ 1.601348] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.620300] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 1.623962] twl 0-0048: PIH (irq 337) nested IRQs [ 1.648071] twl6040 0-004b: clk32k is not handled [ 1.653350] of_get_named_gpiod_flags: parsed 'ti,audpwron-gpio' property of node '/ocp/i2c@48070000/twl@4b[0]' - status (0) [ 1.661346] omap_i2c 48070000.i2c: bus 0 rev0.10 at 400 kHz [ 1.666900] omap_i2c 48072000.i2c: bus 1 rev0.10 at 400 kHz [ 1.671600] omap_i2c 48060000.i2c: bus 2 rev0.10 at 100 kHz [ 1.676544] omap_i2c 48350000.i2c: bus 3 rev0.10 at 400 kHz [ 1.679595] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 1.683410] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.683410] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.691925] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.691925] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.700500] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 1.703674] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 1.703704] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.703704] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.710510] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.720367] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.724029] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 1.727447] omap_hsmmc 4809c000.mmc: omap_device: omap_device_enable() called from invalid state 1 [ 1.779296] omap_hsmmc 480d5000.mmc: GPIO lookup for consumer wp [ 1.780059] omap_hsmmc 480d5000.mmc: using device tree for GPIO lookup [ 1.780059] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480d5000[0]' [ 1.791839] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480d5000[0]' [ 1.791839] omap_hsmmc 480d5000.mmc: using lookup tables for GPIO lookup [ 1.800384] omap_hsmmc 480d5000.mmc: lookup for GPIO wp failed [ 1.803833] omap_hsmmc 480d5000.mmc: omap_device: omap_device_enable() called from invalid state 1 [ 1.946014] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.950561] mmc0: new SD card at address aaaa [ 1.955413] mmcblk0: mmc0:aaaa SD02G 1.89 GiB [ 1.955474] hctosys: unable to open rtc device (rtc0) [ 1.955871] sr_init: No PMIC hook to init smartreflex [ 1.955871] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 1.956665] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 1.956665] smartreflex smartreflex.2: omap_sr_probe: SmartReflex driver initialized [ 1.984680] mmcblk0: p1 p2 [ 1.991851] VDAC: disabling [ 1.994079] VANA: disabling [ 1.996246] VUSB: disabling [ 2.003173] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem [ 2.044158] hw-breakpoint: CPU 0 failed to disable vector catch [ 3.437713] EXT4-fs (mmcblk0p2): recovery complete [ 3.444671] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.444763] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 3.459289] devtmpfs: mounted [ 3.461822] Freeing unused kernel memory: 456K (c08d8000 - c094a000) modprobe: FATAL: Could not load /lib/modules/4.5.0-rc1-196864-g34b4182/modules.dep: No such file or directory INIT: version 2.88 booting Using makefile-style concurrent boot in runlevel S. Starting the hotplug events dispatcher: udevd[ 4.394500] udevd[137]: starting version 172 . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...done. Activating swap...done. [ 6.152404] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Cleaning up ifupdown.... Setting up networking.... Loading kernel modules...done. Activating lvm and md swap...done. Checking file systems...fsck from util-linux 2.19.1 done. Mounting local filesystems...done. Activating swapfile swap...done. Cleaning up temporary files.... Configuring network interfaces...done. Cleaning up temporary files.... Setting kernel variables ...done. [ 8.050476] random: dd urandom read with 54 bits of entropy available INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Debian GNU/Linux wheezy/sid armel ttyO2 armel login: