U-Boot 1.1.4 (Jul 30 2007 - 10:57:36) OMAP2430C-GP revision 3, PRCM #2 TI 2430SDP 1.1 Version + mDDR (Boot NOR) DRAM: 128 MB Flash: 192 MB In: serial Out: serial Err: serial Hit any key to stop autoboot: 3  2  1  0 Using MAC Address 08:00:28:01:17:80 BOOTP broadcast 1 DHCP client bound to address 192.168.57.132 TFTP from server 192.168.57.1; our IP address is 192.168.57.132 Filename 'uImage.sdp2430'. Load address: 0x80000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### done Bytes transferred = 3232448 (3152c0 hex) ## Booting image at 80000000 ... Image Name: Linux-3.5.0-rc5-00010-g8cb8de5 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3232384 Bytes = 3.1 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.5.0-rc5-00010-g8cb8de5 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Wed Jul 4 08:19:41 MDT 2012 [ 0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP2430 sdp2430 board [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32512 [ 0.000000] free_area_init_node: node 0, pgdat c069b680, node_mem_map c0bf6000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32256 pages, LIFO batch:7 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/660/330 MHz [ 0.000000] cm: Module associated with clock apll54_ck didn't enable in 100000 tries [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0cfa000 s11520 r8192 d13056 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32256 [ 0.000000] Kernel command line: console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 116624k/116624k available, 14448k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc05bc5b8 (5842 kB) [ 0.000000] .init : 0xc05bd000 - 0xc0609d00 ( 308 kB) [ 0.000000] .data : 0xc060a000 - 0xc069d670 ( 590 kB) [ 0.000000] .bss : 0xc069d694 - 0xc0bf5d88 (5474 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:474 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.109222] pid_max: default: 32768 minimum: 301 [ 0.110626] Security Framework initialized [ 0.111145] Mount-cache hash table entries: 512 [ 0.125061] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366 [ 0.125152] Setting up static identity map for 0x80406fd8 - 0x80407048 [ 0.128784] Brought up 1 CPUs [ 0.128845] SMP: Total of 1 processors activated (327.68 BogoMIPS). [ 0.159942] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3) [ 0.178192] dummy: [ 0.183319] NET: Registered protocol family 16 [ 0.184448] GPMC revision 3.0 [ 0.184997] gpmc: irq-20 could not claim: err -22 [ 0.204864] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.205993] OMAP GPIO hardware version 2.4 [ 0.208282] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.211883] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.215179] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.219024] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.237060] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.275634] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.275665] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.275695] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.275726] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.275756] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.275787] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.275817] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.275848] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.319915] OMAP DMA hardware revision 4.0 [ 0.477935] bio: create slab at 0 [ 0.497039] SCSI subsystem initialized [ 0.503753] usbcore: registered new interface driver usbfs [ 0.505157] usbcore: registered new interface driver hub [ 0.506958] usbcore: registered new device driver usb [ 0.512756] omap_i2c omap_i2c.1: bus 1 rev1.3.7 at 100 kHz [ 0.520172] omap_i2c omap_i2c.2: bus 2 rev1.3.7 at 100 kHz [ 0.548919] twl 2-0048: PIH (irq 7) chaining IRQs 256..264 [ 0.550384] twl 2-0048: power (irq 261) chaining IRQs 264..271 [ 0.556732] twl4030_gpio twl4030_gpio: gpio (irq 256) chaining IRQs 272..289 [ 0.560821] gpiochip_add: registered GPIOs 192 to 209 on device: twl4030 [ 0.572418] VMMC1: 1850 <--> 3150 mV at 1850 mV normal standby [ 0.593078] Switching to clocksource 32k_counter [ 0.854370] NET: Registered protocol family 2 [ 0.856231] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.861267] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.861968] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) [ 0.866638] TCP: Hash tables configured (established 4096 bind 4096) [ 0.866851] TCP: reno registered [ 0.866943] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.867584] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.869842] NET: Registered protocol family 1 [ 0.873016] RPC: Registered named UNIX socket transport module. [ 0.873046] RPC: Registered udp transport module. [ 0.873077] RPC: Registered tcp transport module. [ 0.873107] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.875427] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.356689] VFS: Disk quotas dquot_6.5.2 [ 1.357635] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.361511] NFS: Registering the id_resolver key type [ 1.362670] Key type id_resolver registered [ 1.365295] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.367706] msgmni has been set to 227 [ 1.378326] io scheduler noop registered [ 1.378387] io scheduler deadline registered [ 1.378784] io scheduler cfq registered (default) [ 1.385772] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.401519] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 2.150421] console [ttyO0] enabled [ 2.158020] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 2.169067] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 74) is a OMAP UART2 [ 2.185913] omap_rng omap_rng: OMAP Random Number Generator ver. 50 [ 2.273529] brd: module loaded [ 2.325225] loop: module loaded [ 2.342895] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.351806] OneNAND driver initializing [ 2.381042] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre [ 2.396636] eth0: SMC91C94 (rev 9) at c8886300 IRQ 245 [nowait] [ 2.403381] eth0: Ethernet addr: 08:00:28:01:17:80 [ 2.408569] eth0: No PHY found [ 2.416381] usbcore: registered new interface driver asix [ 2.423736] usbcore: registered new interface driver cdc_ether [ 2.431488] usbcore: registered new interface driver net1080 [ 2.439056] usbcore: registered new interface driver cdc_subset [ 2.446838] usbcore: registered new interface driver zaurus [ 2.454345] usbcore: registered new interface driver cdc_ncm [ 2.465393] usbcore: registered new interface driver cdc_wdm [ 2.471649] Initializing USB Mass Storage driver... [ 2.478912] usbcore: registered new interface driver usb-storage [ 2.485473] USB Mass Storage support registered. [ 2.493255] usbcore: registered new interface driver libusual [ 2.500732] usbcore: registered new interface driver usbtest [ 2.506958] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) [ 2.520202] mousedev: PS/2 mouse device common for all mice [ 2.540832] input: twl4030_pwrbutton as /devices/platform/omap_i2c.2/i2c-2/2-0049/twl4030_pwrbutton/input/input0 [ 2.558746] twl_rtc twl_rtc: Power up reset detected. [ 2.564910] twl_rtc twl_rtc: Enabling TWL-RTC [ 2.581024] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 2.591308] i2c /dev entries driver [ 2.601837] Driver for 1-wire Dallas network protocol. [ 2.614898] omap_wdt: OMAP Watchdog Timer Rev 0x22: initial timeout 60 sec [ 2.624847] twl4030_wdt twl4030_wdt: Failed to register misc device [ 2.631896] twl4030_wdt: probe of twl4030_wdt failed with error -16 [ 2.819458] usbcore: registered new interface driver usbhid [ 2.825653] usbhid: USB HID core driver [ 2.829833] oprofile: hardware counters not available [ 2.835174] oprofile: using timer interrupt. [ 2.841461] TCP: cubic registered [ 2.845123] Initializing XFRM netlink socket [ 2.849945] NET: Registered protocol family 17 [ 2.855010] NET: Registered protocol family 15 [ 2.860687] Key type dns_resolver registered [ 2.865783] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 2.874298] mux: Failed to setup hwmod io irq -22 [ 2.894836] Power Management for OMAP2 initializing [ 2.900146] PRCM revision 1.0 [ 2.945953] clock: disabling unused clocks to save power [ 2.970092] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.984008] eth0: link up [ 3.008850] Sending DHCP requests ., OK [ 3.032836] IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.57.132 [ 3.041809] IP-Config: Complete: [ 3.045257] device=eth0, addr=192.168.57.132, mask=255.255.255.0, gw=255.255.255.255 [ 3.054046] host=192.168.57.132, domain=, nis-domain=(none) [ 3.060485] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 3.117431] VFS: Mounted root (nfs filesystem) on device 0:11. [ 3.125976] Freeing init memory: 304K [ 3.147979] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.158355] mmc0: new SDHC card at address e624 [ 3.175231] mmcblk0: mmc0:e624 SD04G 3.69 GiB [ 3.213287] mmcblk0: p1 modprobe: FATAL: Could not load /lib/modules/3.5.0-rc5-00010-g8cb8de5/modules.dep: No such file or directory INIT: version 2.88 booting Using makefile-style concurrent boot in runlevel S. Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...done. Activating swap...done. Cleaning up ifupdown.... Setting up networking.... Loading kernel modules...done. Activating lvm and md swap...done. Checking file systems...fsck from util-linux 2.19.1 done. Mounting local filesystems...done. Activating swapfile swap...done. Cleaning up temporary files.... Configuring network interfaces...done. Cleaning up temporary files.... Setting kernel variables ...done. INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Debian GNU/Linux wheezy/sid armel ttyO0 armel login: