£t Texas Instruments X-Loader 1.46 (Jan 22 2011 - 01:46:00) Starting X-loader on MMC Reading boot sector 218976 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... U-Boot 2009.11 (Jan 22 2011 - 01:45:10) OMAP34xx/35xx-GP ES1.0, CPU-OPP2 L3-165MHz AM3517EVM Board + LPDDR/NAND I2C: ready DRAM: 256 MB NAND: 512 MiB In: serial Out: serial Err: serial Die ID #77b0000100000000015da3961500600d Net: davinci_emac_initialize Ethernet PHY: GENERIC @ 0x00 DaVinci EMAC Hit any key to stop autoboot: 3  0 AM3517_EVM # AM3517_EVM # setenv bootfile uImage-dtb.am3517-evm AM3517_EVM # AM3517_EVM # setenv loadaddr 0x81000000 AM3517_EVM # AM3517_EVM # dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.57.129 Using DaVinci EMAC device TFTP from server 192.168.57.1; our IP address is 192.168.57.129 Filename 'uImage-dtb.am3517-evm'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ### done Bytes transferred = 4336917 (422d15 hex) AM3517_EVM # setenv bootargs console=ttyO2,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p2 rootwait init=/bin/sh nohlt AM3517_EVM # AM3517_EVM # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4336853 Bytes = 4.1 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.15.0-rc1-13732-g48664ff (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Thu May 15 21:35:24 MDT 2014 [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine model: TI AM3517 EVM (AM3517/05 TMDSEVM3517) [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at 8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c0894700, node_mem_map cfcf2000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM3517 ES1.1 (l2cache sgx neon ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @cfcb3000 s14080 r8192 d14592 u36864 [ 0.000000] pcpu-alloc: s14080 r8192 d14592 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO2,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p2 rootwait init=/bin/sh nohlt [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 227824K/261120K available (5572K kernel code, 663K rwdata, 2144K rodata, 389K init, 5522K bss, 33296K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0791304 (7717 kB) [ 0.000000] .init : 0xc0792000 - 0xc07f3700 ( 390 kB) [ 0.000000] .data : 0xc07f4000 - 0xc0899f00 ( 664 kB) [ 0.000000] .bss : 0xc0899f00 - 0xc0dfead0 (5523 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz [ 0.000000] OMAP clockevent source: timer2 at 13000000 Hz [ 0.000030] sched_clock: 32 bits at 13MHz, resolution 76ns, wraps every 330382100403ns [ 0.000131] OMAP clocksource: timer1 at 13000000 Hz [ 0.001473] Console: colour dummy device 80x30 [ 0.001565] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001583] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001598] ... MAX_LOCK_DEPTH: 48 [ 0.001613] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001627] ... CLASSHASH_SIZE: 4096 [ 0.001641] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.001655] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.001668] ... CHAINHASH_SIZE: 16384 [ 0.001682] memory used by lock dependency info: 3695 kB [ 0.001697] per task-struct memory footprint: 1152 bytes [ 0.001766] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696) [ 0.096415] pid_max: default: 32768 minimum: 301 [ 0.097142] Security Framework initialized [ 0.097379] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.097406] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.101460] CPU: Testing write buffer coherency: ok [ 0.103416] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.103560] Setting up static identity map for 0x80548010 - 0x80548080 [ 0.109216] Brought up 1 CPUs [ 0.109248] SMP: Total of 1 processors activated. [ 0.109265] CPU: All CPU(s) started in SVC mode. [ 0.114006] devtmpfs: initialized [ 0.126842] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 [ 0.194242] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.196179] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.215500] omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm [ 0.217704] omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm [ 0.271253] omap_hwmod: uart4: cannot be enabled for reset (3) [ 0.291111] pinctrl core: initialized pinctrl subsystem [ 0.295498] regulator-dummy: no parameters [ 0.384353] NET: Registered protocol family 16 [ 0.394965] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.412113] Reprogramming SDRC clock to 332000000 Hz [ 0.415007] platform iva.2: Cannot lookup hwmod 'iva' [ 0.416880] platform 480c5000.aes: Cannot lookup hwmod 'aes' [ 0.427616] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.429154] OMAP GPIO hardware version 2.5 [ 0.431232] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.434431] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.437744] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.440827] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.443898] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.451301] platform 48094000.mailbox: Cannot lookup hwmod 'mailbox' [ 0.457467] platform 480bd400.mmu: Cannot lookup hwmod 'mmu_isp' [ 0.459253] platform 480c3000.sham: Cannot lookup hwmod 'sham' [ 0.460095] platform 480cb000.smartreflex: Cannot lookup hwmod 'smartreflex_core' [ 0.460914] platform 480c9000.smartreflex: Cannot lookup hwmod 'smartreflex_mpu_iva' [ 0.472545] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 0.473891] platform 480ab000.usb_otg_hs: Cannot lookup hwmod 'usb_otg_hs' [ 0.477634] No ATAGs? [ 0.477669] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.482002] OMAP DMA hardware revision 4.0 [ 0.528305] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.528425] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 0.592755] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.594041] of_get_named_gpiod_flags: can't parse gpios property of node '/vmmc[0]' [ 0.594989] vmmc_fixed: 3300 mV [ 0.601564] SCSI subsystem initialized [ 0.603040] usbcore: registered new interface driver usbfs [ 0.603371] usbcore: registered new interface driver hub [ 0.604752] usbcore: registered new device driver usb [ 0.609456] omap_i2c 48070000.i2c: bus 0 rev3.3 at 400 kHz [ 0.612036] omap_i2c 48072000.i2c: bus 1 rev3.3 at 400 kHz [ 0.614232] omap_i2c 48060000.i2c: bus 2 rev3.3 at 400 kHz [ 0.621608] Switched to clocksource timer1 [ 0.909345] NET: Registered protocol family 2 [ 0.912563] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.912817] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.913972] TCP: Hash tables configured (established 2048 bind 2048) [ 0.914258] TCP: reno registered [ 0.914306] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.914630] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.916382] NET: Registered protocol family 1 [ 0.919499] RPC: Registered named UNIX socket transport module. [ 0.919540] RPC: Registered udp transport module. [ 0.919559] RPC: Registered tcp transport module. [ 0.919578] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.921806] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.930443] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.155072] VFS: Disk quotas dquot_6.5.2 [ 1.155306] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.159812] NFS: Registering the id_resolver key type [ 1.160483] Key type id_resolver registered [ 1.160518] Key type id_legacy registered [ 1.160716] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.161688] msgmni has been set to 476 [ 1.171717] io scheduler noop registered [ 1.171758] io scheduler deadline registered [ 1.171897] io scheduler cfq registered (default) [ 1.175455] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568 [ 1.176310] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92 [ 1.180379] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV [ 1.182626] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.195312] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.195371] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]' [ 1.198108] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.201207] omap_uart 4806c000.serial: no wakeirq for uart0 [ 1.201262] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]' [ 1.203255] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 1.205447] omap_uart 49020000.serial: no wakeirq for uart0 [ 1.205496] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@49020000[0]' [ 1.206953] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 2.112930] console [ttyO2] enabled [ 2.186863] brd: module loaded [ 2.218574] loop: module loaded [ 2.227033] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.291898] davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 [ 2.298400] davinci_mdio davinci_mdio.0: no live phy, scanning all [ 2.307305] davinci_mdio: probe of davinci_mdio.0 failed with error -5 [ 2.315495] usbcore: registered new interface driver asix [ 2.321847] usbcore: registered new interface driver ax88179_178a [ 2.328460] usbcore: registered new interface driver cdc_ether [ 2.335028] usbcore: registered new interface driver smsc95xx [ 2.341425] usbcore: registered new interface driver net1080 [ 2.347578] usbcore: registered new interface driver cdc_subset [ 2.354117] usbcore: registered new interface driver zaurus [ 2.360314] usbcore: registered new interface driver cdc_ncm [ 2.371915] usbcore: registered new interface driver cdc_wdm [ 2.378214] usbcore: registered new interface driver usb-storage [ 2.384923] usbcore: registered new interface driver usbtest [ 2.395125] mousedev: PS/2 mouse device common for all mice [ 2.407742] i2c /dev entries driver [ 2.416571] Driver for 1-wire Dallas network protocol. [ 2.430163] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.439940] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.449193] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.470417] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.523235] usbcore: registered new interface driver usbhid [ 2.529089] usbhid: USB HID core driver [ 2.535280] oprofile: using arm/armv7 [ 2.540303] TCP: cubic registered [ 2.544008] Initializing XFRM netlink socket [ 2.548737] NET: Registered protocol family 17 [ 2.553672] NET: Registered protocol family 15 [ 2.558941] Key type dns_resolver registered [ 2.565733] PM: no software I/O chain control; some wakeups may be lost [ 2.572887] pm: Failed to request pm_wkup irq [ 2.577494] ThumbEE CPU extension supported. [ 2.582179] Registering SWP/SWPB emulation handler [ 2.622674] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.707225] Waiting for root device /dev/mmcblk0p2... [ 2.743138] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.754291] mmc0: new high speed SDHC card at address b368 [ 2.766113] mmcblk0: mmc0:b368 USD 3.75 GiB [ 2.779519] mmcblk0: p1 p2 p3 [ 2.840562] kjournald starting. Commit interval 5 seconds [ 2.847129] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.854739] VFS: Mounted root (ext3 filesystem) readonly on device 179:2. [ 2.871107] devtmpfs: mounted [ 2.875840] Freeing unused kernel memory: 388K (c0792000 - c07f3000) /bin/sh: can't access tty; jïÿ/ # / # / #