$ ÿNOLO X-Loader (v1.1.16, Oct 31 2008) Secondary image size 99036 Booting secondary Nokia OMAP Loader v1.1.16 (Oct 31 2008) running on Nokia N800 F5 (RX-34) Clocks: Core: 658 MHz L3: 109 MHz L4: 109 MHz MPU: 329 MHz DSP: 219 MHz IVA: 109 MHz I2C v3.4 Menelaus v2.2 found Vilma v1.5 found Betty v2.1 found Reset reason: pwr_key System DMA v2.0 OneNAND blocks unlocked in 30264 us Flash id: ec4811 Partition table successfully read McSPI v1.4 RFBI version 1.0 Detecting LCD panel lph8923 Panel ID: 838f48 URAL panel detected Detected LCD panel: ls041y3 S1D13745 Hailstorm detected FB memory blanking took 242 ms (3089 kB/s) Logo drawn in 24 ms (1218 kB/s) Über-cool backlight fade-in took 101 ms Prompt keypress detected Initializing USB No USB host detected nolo> u Initializing USB Entering USB loop SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 64 bytes) SETUP: WR STD DEVICE SET_ADDRESS value 0015 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 18 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 9 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 94 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 00, index 0000, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 02, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 01, index 0409, length 255 bytes) SETUP: WR STD DEVICE SET_CONFIGURATION value 0001 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 03, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0001 index 0002 length 0000 Flashing interface selected SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 Flashing mode entered SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 SETUP: RD VND DEVICE req 04 value 0000 index 0000 length 0200 SETUP: RD VND DEVICE req 03 value 0000 index 0000 length 0004 SETUP: WR VND DEVICE req 12 value 0000 index 0000 length 0012 SETUP: RD VND DEVICE req 14 value 0000 index 0000 length 0200 SETUP: WR VND DEVICE req 42 value 0000 index 0000 length 001b Receiving kernel (length 1703040) Image successfully received SETUP: WR VND DEVICE req 82 value 0000 index 0000 length 0000 SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 Boot requested [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.9.0-rc5-27673-g469d633 (paul@knihy) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Sun Mar 31 21:18:58 MDT 2013 [ 0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Nokia N800 [ 0.000000] Ignoring unrecognised tag 0x414f4d50 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at 87000000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c0356cf8, node_mem_map c0875000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP2420 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttyO2,115200 earlyprintk debug init=/bin/bash ignore_loglevel [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 104820k/104820k available, 26252k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc02fc0e4 (3025 kB) [ 0.000000] .init : 0xc02fd000 - 0xc032145c ( 146 kB) [ 0.000000] .data : 0xc0322000 - 0xc0357900 ( 215 kB) [ 0.000000] .bss : 0xc0357900 - 0xc0874f9c (5238 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.002227] Calibrating delay loop... 217.49 BogoMIPS (lpj=1087488) [ 0.129608] pid_max: default: 32768 minimum: 301 [ 0.130340] Security Framework initialized [ 0.130554] Mount-cache hash table entries: 512 [ 0.139129] CPU: Testing write buffer coherency: ok [ 0.142791] Setting up static identity map for 0xc021a070 - 0xc021a0e0 [ 0.153045] devtmpfs: initialized [ 0.162353] ttyO2 used as console in debug mode: uart2 clocks will not be gated [ 0.197937] pinctrl core: initialized pinctrl subsystem [ 0.213745] regulator-dummy: no parameters [ 0.232299] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.235412] omap-gpmc omap-gpmc: GPMC revision 2.0 [ 0.254821] omap_gpio omap_gpio.0: Could not get gpio dbck [ 0.258941] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.260223] OMAP GPIO hardware version 1.8 [ 0.262908] omap_gpio omap_gpio.1: Could not get gpio dbck [ 0.265228] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.268676] omap_gpio omap_gpio.2: Could not get gpio dbck [ 0.270751] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.274383] omap_gpio omap_gpio.3: Could not get gpio dbck [ 0.276397] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.288146] omap_mux_init: Add partition: #1: core, flags: b [ 0.365661] mmci-omap.0: alias fck already exists [ 0.369812] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.369842] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.401885] OMAP DMA hardware revision 2.0 [ 0.404907] Serial: AMBA PL011 UART driver [ 0.477813] bio: create slab at 0 [ 0.714691] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.724212] SCSI subsystem initialized [ 0.736236] omap_i2c omap_i2c.1: bus 1 rev3.3 at 400 kHz [ 0.739898] omap_i2c omap_i2c.2: bus 2 rev3.3 at 400 kHz [ 0.747009] Switching to clocksource 32k_counter [ 0.924591] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.925262] CPU PMU: probing PMU on CPU 0 [ 0.925323] hw perfevents: enabled with v6 PMU driver, 3 counters available [ 0.958892] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.960601] msgmni has been set to 236 [ 0.964385] io scheduler noop registered [ 0.964630] io scheduler cfq registered (default) [ 0.968780] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.989227] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0 [ 0.995391] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1 [ 1.000671] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 90) is a OMAP UART2 [ 1.593322] console [ttyO2] enabled [ 1.608795] omap_rng omap_rng: OMAP Random Number Generator ver. 40 [ 1.621276] Menelaus rev 2.2 [ 1.654205] OneNAND driver initializing [ 1.660552] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c8880000, freq 54 MHz [ 1.672058] OneNAND Manufacturer: Samsung (0xec) [ 1.677001] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48) [ 1.682617] OneNAND version = 0x0011 [ 1.686431] Chip support all block unlock [ 1.690856] onenand_wait: controller error! state 15 ctrl 0x0440 intr 0x8000 [ 1.700195] Scanning device for bad blocks [ 1.713073] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x39 addr8 0x0 [ 1.721496] OneNAND eraseblock 57 is an initial bad block [ 1.727386] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3a addr8 0x0 [ 1.735687] OneNAND eraseblock 58 is an initial bad block [ 1.741577] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3b addr8 0x0 [ 1.749969] OneNAND eraseblock 59 is an initial bad block [ 1.768951] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xa7 addr8 0x0 [ 1.777252] OneNAND eraseblock 167 is an initial bad block [ 1.784820] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xb5 addr8 0x0 [ 1.793212] OneNAND eraseblock 181 is an initial bad block [ 1.832824] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x1c9 addr8 0x0 [ 1.841339] OneNAND eraseblock 457 is an initial bad block [ 2.046081] Creating 5 MTD partitions on "omap2-onenand": [ 2.052734] 0x000000000000-0x000000020000 : "bootloader" [ 2.076354] 0x000000020000-0x000000080000 : "config" [ 2.093017] 0x000000080000-0x000000280000 : "kernel" [ 2.110900] 0x000000280000-0x000000680000 : "initfs" [ 2.128082] 0x000000680000-0x000010000000 : "rootfs" [ 2.168426] i2c /dev entries driver [ 2.192749] retu-mfd 3-0001: Retu & Vilma v1.5 found [ 2.214477] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec [ 2.230133] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 2.237457] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 2.360046] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.367309] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.400543] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.407165] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.413818] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.422302] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.439270] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 2.447753] mux: Failed to setup hwmod io irq -22 [ 2.465576] Power Management for OMAP2 initializing [ 2.470916] PRCM revision 1.0 [ 2.486419] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.500427] Waiting for root device /dev/mmcblk0p1... [ 3.048156] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.057434] mmc0: new SDHC card at address 1234 [ 3.068206] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 3.087768] mmcblk0: p1 [ 3.100341] mmci-omap mmci-omap.0: command timeout (CMD52) [ 3.107055] mmci-omap mmci-omap.0: command timeout (CMD52) [ 3.117675] mmci-omap mmci-omap.0: command timeout (CMD8) [ 3.124267] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.130859] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.137420] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.143951] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.150543] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.157165] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.171264] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.178710] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.186859] mmci-omap mmci-omap.0: command timeout (CMD1) [ 3.989868] kjournald starting. Commit interval 5 seconds [ 4.214355] EXT3-fs (mmcblk0p1): using internal journal [ 4.234161] EXT3-fs (mmcblk0p1): recovery complete [ 4.239440] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode [ 4.247039] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 4.262329] devtmpfs: mounted [ 4.266571] Freeing init memory: 144K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#