U-Boot 1.1.4 (Mar 18 2007 - 12:22:00)

OMAP2430C-GP revision 3, PRCM #5A
TI 2430SDP 1.1 Version + mDDR (Boot NOR)
DRAM:  128 MB
Flash: 192 MB
NAND:64 MB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  3  0 
OMAP243X SDP # 
OMAP243X SDP # setenv bootargs console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh
OMAP243X SDP # loady
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CSending: uImage-dtb.omap2430-sdp
Sending: 

Transfer complete
em - CRC mode, 8(SOH)/3391(STX)/0(CAN) packets, 3 retries
## Total Size      = 0x0034fec7 = 3473095 Bytes
OMAP243X SDP # bootm
## Booting image at 80000000 ...
   Image Name:   Linux-
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3473031 Bytes =  3.3 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
OK

Starting kernel ...

%% Start PM consolidated quick test (retention only)


%% Preparation

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.1.0-rc2-142403-g6589aa0 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Mon May 11 11:57:19 MDT 2015
[    0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d
[    0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: TI OMAP2430 SDP
[    0.000000] earlycon: no match for ttyO0,115200n8
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] cma: Reserved 16 MiB at 0x86800000
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 32512
[    0.000000] free_area_init_node: node 0, pgdat c0958600, node_mem_map c7dd1000
[    0.000000]   Normal zone: 288 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32512 pages, LIFO batch:7
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] OMAP2430
[    0.000000] 
[    0.000000] PERCPU: Embedded 13 pages/cpu @c7d6e000 s22976 r8192 d22080 u53248
[    0.000000] pcpu-alloc: s22976 r8192 d22080 u53248 alloc=13*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32224
[    0.000000] Kernel command line: console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 94112K/130048K available (6211K kernel code, 739K rwdata, 2168K rodata, 440K init, 8220K bss, 19552K reserved, 16384K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc083700c   (8381 kB)
[    0.000000]       .init : 0xc0838000 - 0xc08a6000   ( 440 kB)
[    0.000000]       .data : 0xc08a6000 - 0xc095ec58   ( 740 kB)
[    0.000000]        .bss : 0xc0961000 - 0xc11683d0   (8221 kB)
[    0.000000] Running RCU self tests
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU lockdep checking is enabled.
[    0.000000] 	Additional per-CPU info printed with stalls.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts
[    0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] clocksource 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns
[    0.000061] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000640] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present.
[    0.003387] Console: colour dummy device 80x30
[    0.003601] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.003631] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.003662] ... MAX_LOCK_DEPTH:          48
[    0.003692] ... MAX_LOCKDEP_KEYS:        8191
[    0.003723] ... CLASSHASH_SIZE:          4096
[    0.003723] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.003753] ... MAX_LOCKDEP_CHAINS:      65536
[    0.003784] ... CHAINHASH_SIZE:          32768
[    0.003814]  memory used by lock dependency info: 5167 kB
[    0.003845]  per task-struct memory footprint: 1152 bytes
[    0.003906] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
[    0.114562] pid_max: default: 32768 minimum: 301
[    0.115844] Security Framework initialized
[    0.116424] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.116485] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.129119] Initializing cgroup subsys blkio
[    0.129241] Initializing cgroup subsys memory
[    0.129516] Initializing cgroup subsys devices
[    0.129852] Initializing cgroup subsys freezer
[    0.130401] Initializing cgroup subsys perf_event
[    0.130645] CPU: Testing write buffer coherency: ok
[    0.136657] missing device node for CPU 0
[    0.136749] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366
[    0.137023] Setting up static identity map for 0x80008280 - 0x800082f0
[    0.154785] Brought up 1 CPUs
[    0.154846] SMP: Total of 1 processors activated (262.96 BogoMIPS).
[    0.154876] CPU: All CPU(s) started in SVC mode.
[    0.169403] devtmpfs: initialized
[    0.199768] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2
[    0.327392] omap_hwmod: usb_otg_hs: _wait_target_ready failed: -16
[    0.327453] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3)
[    0.350616] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.358825] pinctrl core: initialized pinctrl subsystem
[    0.549835] NET: Registered protocol family 16
[    0.574707] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.582641] cpuidle: using governor ladder
[    0.582763] cpuidle: using governor menu
[    0.659698] omap_gpio 4900c000.gpio: Could not get gpio dbck
[    0.663604] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.667572] OMAP GPIO hardware version 2.4
[    0.670715] omap_gpio 4900e000.gpio: Could not get gpio dbck
[    0.672424] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.678497] omap_gpio 49010000.gpio: Could not get gpio dbck
[    0.679748] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.685791] omap_gpio 49012000.gpio: Could not get gpio dbck
[    0.687072] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.692993] omap_gpio 480b6000.gpio: Could not get gpio dbck
[    0.694702] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
[    0.701019] omap-gpmc 6e000000.gpmc: GPMC revision 3.0
[    0.719116] No ATAGs?
[    0.719329] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[    0.719360] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.727905] OMAP DMA hardware revision 4.0
[    0.951721] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver
[    0.966400] SCSI subsystem initialized
[    0.968719] libata version 3.00 loaded.
[    0.979339] omap_i2c 48070000.i2c: bus 0 rev3.3 at 100 kHz
[    0.985626] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz
[    1.003997] Switched to clocksource 32k_counter
[    1.618682] NET: Registered protocol family 2
[    1.626342] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.626892] TCP bind hash table entries: 1024 (order: 3, 36864 bytes)
[    1.628326] TCP: Hash tables configured (established 1024 bind 1024)
[    1.629058] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    1.629852] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    1.633941] NET: Registered protocol family 1
[    1.640594] RPC: Registered named UNIX socket transport module.
[    1.640655] RPC: Registered udp transport module.
[    1.640686] RPC: Registered tcp transport module.
[    1.640747] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.647521] CPU PMU: Failed to parse <no-node>/interrupt-affinity[0]
[    1.647796] hw perfevents: enabled with armv6_1136 PMU driver, 3 counters available
[    1.668609] futex hash table entries: 256 (order: 2, 16384 bytes)
[    1.669433] audit: initializing netlink subsys (disabled)
[    1.670288] audit: type=2000 audit(1.660:1): initialized
[    1.688018] VFS: Disk quotas dquot_6.6.0
[    1.688537] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.699829] NFS: Registering the id_resolver key type
[    1.701690] Key type id_resolver registered
[    1.701751] Key type id_legacy registered
[    1.702606] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.726562] io scheduler noop registered
[    1.726654] io scheduler deadline registered
[    1.726837] io scheduler cfq registered (default)
[    1.736450] pinctrl-single 49002030.pinmux: 340 pins at pa fb002030 size 340
[    1.745910] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.770660] omap_uart 4806a000.serial: no wakeirq for uart0
[    1.770751] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]'
[    1.772735] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[    2.638458] console [ttyO0] enabled
[    2.651184] omap_uart 4806c000.serial: no wakeirq for uart1
[    2.657379] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]'
[    2.668365] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    2.682922] omap_uart 4806e000.serial: no wakeirq for uart2
[    2.689025] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]'
[    2.700012] 4806e000.serial: ttyO2 at MMIO 0x4806e000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[    2.829010] brd: module loaded
[    2.904174] loop: module loaded
[    2.953552] twl 1-0048: PIH (irq 23) chaining IRQs 274..282
[    2.960845] twl 1-0048: power (irq 279) chaining IRQs 282..289
[    3.156646] twl4030_gpio twl4030-gpio: gpio (irq 274) chaining IRQs 290..307
[    3.166656] gpiochip_find_base: found new base at 494
[    3.174407] gpiochip_add: registered GPIOs 494 to 511 on device: twl4030
[    3.206665] mtdoops: mtd device (mtddev=name/number) must be supplied
[    3.239410] smc91x 8000300.ethernet: GPIO lookup for consumer power
[    3.246215] smc91x 8000300.ethernet: using device tree for GPIO lookup
[    3.253326] of_get_named_gpiod_flags: can't parse 'power-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]'
[    3.264739] of_get_named_gpiod_flags: can't parse 'power-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]'
[    3.275970] smc91x 8000300.ethernet: using lookup tables for GPIO lookup
[    3.283843] smc91x 8000300.ethernet: lookup for GPIO power failed
[    3.290313] smc91x 8000300.ethernet: GPIO lookup for consumer reset
[    3.297027] smc91x 8000300.ethernet: using device tree for GPIO lookup
[    3.304046] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]'
[    3.315429] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]'
[    3.326690] smc91x 8000300.ethernet: using lookup tables for GPIO lookup
[    3.333862] smc91x 8000300.ethernet: lookup for GPIO reset failed
[    3.340454] smc91x 8000300.ethernet (unnamed net_device) (uninitialized): smc91x: IOADDR c890a300 doesn't match configuration (0).
[    3.352966] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico@fluxnic.net>
[    3.369232] smc91x 8000300.ethernet eth0: SMC91C94 (rev 9) at c890a300 IRQ 261
[    3.377044] 
[    3.378662] smc91x 8000300.ethernet eth0: Ethernet addr: 10:03:31:33:16:8f
[    3.400482] mousedev: PS/2 mouse device common for all mice
[    3.406677] i2c /dev entries driver
[    3.424621] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd
[    3.430969] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup
[    3.438049] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]'
[    3.447814] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]'
[    3.457427] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup
[    3.464599] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed
[    3.470794] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp
[    3.477233] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup
[    3.484252] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]'
[    3.493957] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]'
[    3.503601] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup
[    3.510681] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed
[    3.575286] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd
[    3.581634] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup
[    3.588684] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]'
[    3.598419] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]'
[    3.608032] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup
[    3.615234] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed
[    3.621429] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp
[    3.627838] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup
[    3.634826] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]'
[    3.644561] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]'
[    3.654205] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup
[    3.661285] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed
[    3.668670] 480b4000.mmc supply vmmc not found, using dummy regulator
[    3.676391] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22)
[    3.684906] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22)
[    3.724914] ledtrig-cpu: registered to indicate activity on CPUs
[    3.736053] oprofile: using arm/armv6
[    3.743011] Initializing XFRM netlink socket
[    3.748352] NET: Registered protocol family 17
[    3.753570] NET: Registered protocol family 15
[    3.759826] Key type dns_resolver registered
[    3.765045] SmartReflex Class3 initialized
[    3.805541] hctosys: unable to open rtc device (rtc0)
[    3.810913] sr_init: No PMIC hook to init smartreflex
[    3.817413] sr_init: platform driver register failed for SR
[    3.960388] VUSB3V1: disabling
[    3.967285] VUSB1V8: disabling
[    3.973999] VUSB1V5: disabling
[    3.999359] Waiting for root device /dev/mmcblk0p1...