U-Boot SPL 2013.01-rc1-00207-gfbeb8fc-dirty (Nov 29 2012 - 03:05:13) OMAP4460 ES1.1 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.01-rc1-00207-gfbeb8fc-dirty (Nov 29 2012 - 03:05:13) CPU : OMAP4460 ES1.1 Board: OMAP4 Panda I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3  0 Panda # Panda # setenv bootargs console=ttyO2,230400n8 root=/dev/mmcblk0p2 rootwait vram=32M debug earlyprintk ignore_loglevel init=/bin/sh Panda # loady ## Ready for binary (ymodem) download to 0x82000000 at 230400 bps... CSending: uImage Sending: Transfer complete xyzModem - CRC mode, 6(SOH)/4256(STX)/0(CAN) packets, 3 retries ## Total Size = 0x004281a8 = 4358568 Bytes Panda # bootm ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.10.0-rc5-00322-g317ddd2 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4358504 Bytes = 4.2 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.10.0-rc5-00322-g317ddd2 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Sun Jun 9 03:17:40 MDT 2013 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP4 Panda board [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at ae800000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] On node 0 totalpages: 261888 [ 0.000000] free_area_init_node: node 0, pgdat c084d000, node_mem_map c0db6000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 528 pages used for memmap [ 0.000000] HighMem zone: 67328 pages, LIFO batch:15 [ 0.000000] OMAP4460 ES1.1 [ 0.000000] PERCPU: Embedded 9 pages/cpu @c15c9000 s13632 r8192 d15040 u36864 [ 0.000000] pcpu-alloc: s13632 r8192 d15040 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260368 [ 0.000000] Kernel command line: console=ttyO2,230400n8 root=/dev/mmcblk0p2 rootwait vram=32M debug earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1023MB = 1023MB total [ 0.000000] Memory: 1007964k/1007964k available, 40612k reserved, 269312K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07577bc (7486 kB) [ 0.000000] .init : 0xc0758000 - 0xc07ba540 ( 394 kB) [ 0.000000] .data : 0xc07bc000 - 0xc0851588 ( 598 kB) [ 0.000000] .bss : 0xc0851588 - 0xc0db59d8 (5522 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.001037] Calibrating delay loop... 1391.00 BogoMIPS (lpj=6955008) [ 0.079742] pid_max: default: 32768 minimum: 301 [ 0.080322] Security Framework initialized [ 0.080505] Mount-cache hash table entries: 512 [ 0.084106] CPU: Testing write buffer coherency: ok [ 0.085571] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.085845] Setting up static identity map for 0xc054f7f0 - 0xc054f860 [ 0.085906] L310 cache controller enabled [ 0.085937] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e470000, Cache size: 1048576 B [ 0.090179] CPU1: Booted secondary processor [ 0.175811] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.176239] Brought up 2 CPUs [ 0.176269] SMP: Total of 2 processors activated (2788.55 BogoMIPS). [ 0.176269] CPU: All CPU(s) started in SVC mode. [ 0.178649] devtmpfs: initialized [ 0.187896] ttyO2 used as console in debug mode: uart2 clocks will not be gated [ 0.248992] pinctrl core: initialized pinctrl subsystem [ 0.252105] regulator-dummy: no parameters [ 0.254791] NET: Registered protocol family 16 [ 0.262634] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.263824] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 0.270385] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.271453] OMAP GPIO hardware version 0.1 [ 0.272338] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.273864] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.275390] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.277069] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.278625] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.283660] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.285430] omap_mux_init: Add partition: #2: wkup, flags: 3 [ 0.285583] error setting wl12xx data: -38 [ 0.285858] omap_mux_get_by_name: Could not find signal sys_nirq [ 0.289916] omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx [ 0.360076] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.360107] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.372161] OMAP DMA hardware revision 0.0 [ 0.375244] arm-pmu: alias fck already exists [ 0.414978] bio: create slab at 0 [ 0.469390] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.470458] vwl1271: 1800 mV [ 0.471221] hsusb1_reset: 3300 mV [ 0.471954] hsusb1_vcc: 3300 mV [ 0.476959] SCSI subsystem initialized [ 0.478393] usbcore: registered new interface driver usbfs [ 0.478698] usbcore: registered new interface driver hub [ 0.479125] usbcore: registered new device driver usb [ 0.484558] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 0.486541] twl 1-0048: PIH (irq 39) chaining IRQs 418..438 [ 0.488525] VUSB: 3300 mV normal standby [ 0.489868] vdd_mpu: 500 <--> 1500 mV normal [ 0.491149] vdd_iva: 500 <--> 1500 mV normal [ 0.492370] vdd_core: 500 <--> 1500 mV normal [ 0.494079] V1V8: 1800 mV normal standby [ 0.495361] V2V1: 2100 mV normal standby [ 0.496948] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby [ 0.498626] VPP: 1800 <--> 2500 mV at 1900 mV normal standby [ 0.500518] VCXIO: 1800 mV normal standby [ 0.500610] VCXIO: supplied by V2V1 [ 0.503173] VDAC: 1800 mV normal standby [ 0.503265] VDAC: supplied by V2V1 [ 0.505310] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby [ 0.508026] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby [ 0.510009] VANA: 2100 mV normal standby [ 0.510894] omap_i2c omap_i2c.1: bus 1 rev0.11 at 400 kHz [ 0.511779] omap_i2c omap_i2c.2: bus 2 rev0.11 at 400 kHz [ 0.513031] omap_i2c omap_i2c.3: bus 3 rev0.11 at 100 kHz [ 0.513824] omap_i2c omap_i2c.4: bus 4 rev0.11 at 400 kHz [ 0.519500] Switching to clocksource 32k_counter [ 0.620880] NET: Registered protocol family 2 [ 0.622619] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.622955] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.625640] TCP: Hash tables configured (established 8192 bind 8192) [ 0.625885] TCP: reno registered [ 0.625915] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.626281] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.627624] NET: Registered protocol family 1 [ 0.628753] RPC: Registered named UNIX socket transport module. [ 0.628753] RPC: Registered udp transport module. [ 0.628784] RPC: Registered tcp transport module. [ 0.628784] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.629577] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.629943] CPU PMU: probing PMU on CPU 1 [ 0.630004] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.797637] bounce pool size: 64 pages [ 0.798217] VFS: Disk quotas dquot_6.5.2 [ 0.798431] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.800781] NFS: Registering the id_resolver key type [ 0.801147] Key type id_resolver registered [ 0.801147] Key type id_legacy registered [ 0.801269] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.801849] msgmni has been set to 1474 [ 0.804351] io scheduler noop registered [ 0.804382] io scheduler deadline registered [ 0.804504] io scheduler cfq registered (default) [ 0.807342] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.812652] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0 [ 0.814392] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1 [ 0.815704] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2 [ 1.265869] console [ttyO2] enabled [ 1.269012] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3 [ 1.295166] brd: module loaded [ 1.309875] loop: module loaded [ 1.320281] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.331634] usbcore: registered new interface driver asix [ 1.334899] usbcore: registered new interface driver ax88179_178a [ 1.338500] usbcore: registered new interface driver cdc_ether [ 1.342590] usbcore: registered new interface driver smsc95xx [ 1.346038] usbcore: registered new interface driver net1080 [ 1.349426] usbcore: registered new interface driver cdc_subset [ 1.352996] usbcore: registered new interface driver zaurus [ 1.356384] usbcore: registered new interface driver cdc_ncm [ 1.360870] usbcore: registered new interface driver cdc_wdm [ 1.364288] usbcore: registered new interface driver usb-storage [ 1.367889] usbcore: registered new interface driver usbtest [ 1.372406] mousedev: PS/2 mouse device common for all mice [ 1.378997] twl_rtc twl_rtc: Power up reset detected. [ 1.382781] twl_rtc twl_rtc: Enabling TWL-RTC [ 1.389190] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 1.393096] i2c /dev entries driver [ 1.397979] Driver for 1-wire Dallas network protocol. [ 1.403869] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.409698] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 1.413360] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 1.470153] omap-dma-engine omap-dma-engine: allocating channel for 60 [ 1.473754] omap-dma-engine omap-dma-engine: allocating channel for 59 [ 1.582794] usbcore: registered new interface driver usbhid [ 1.585235] mmc1: card claims to support voltages below the defined range. These will be ignored. [ 1.590728] usbhid: USB HID core driver [ 1.593719] oprofile: using arm/armv7-ca9 [ 1.596130] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 1.596435] TCP: cubic registered [ 1.596466] Initializing XFRM netlink socket [ 1.596557] NET: Registered protocol family 17 [ 1.596618] NET: Registered protocol family 15 [ 1.596923] Key type dns_resolver registered [ 1.610443] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.612060] mmc1: new SDIO card at address 0001 [ 1.628448] Power Management for TI OMAP4. [ 1.630737] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.634582] ThumbEE CPU extension supported. [ 1.639892] VANA: incomplete constraints, leaving on [ 1.643981] VDAC: incomplete constraints, leaving on [ 1.647613] VUSB: incomplete constraints, leaving on [ 1.653869] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 1.661773] Waiting for root device /dev/mmcblk0p2... [ 1.978668] mmc0: host does not support reading read-only switch. assuming write-enable. [ 1.985961] mmc0: new high speed SD card at address 1234 [ 1.990386] mmcblk0: mmc0:1234 SA02G 1.83 GiB [ 1.998382] mmcblk0: p1 p2 [ 2.945068] kjournald starting. Commit interval 5 seconds [ 2.945312] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended [ 3.342407] EXT3-fs (mmcblk0p2): using internal journal [ 3.347259] ext3_orphan_cleanup: truncating inode 20 to 0 bytes [ 3.351623] EXT3-fs (mmcblk0p2): 1 truncate cleaned up [ 4.572143] EXT3-fs (mmcblk0p2): recovery complete [ 4.574829] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 4.578735] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 4.586120] devtmpfs: mounted [ 4.588165] Freeing unused kernel memory: 392K (c0758000 - c07ba000) /bin/sh: can't access tty; job control turned off / #