U-Boot SPL 2013.01-rc1-00207-gfbeb8fc-dirty (Nov 29 2012 - 03:05:13) OMAP4460 ES1.1 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.01-rc1-00207-gfbeb8fc-dirty (Nov 29 2012 - 03:05:13) CPU : OMAP4460 ES1.1 Board: OMAP4 Panda I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3  0 Panda # Panda # setenv bootargs 'console=ttyO2,230400n8 root=/dev/mmcblk0p2 rootwait vram=32M earlyprintk ignore_loglevel init=/bin/sh' Panda # loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 230400 bps... CSending: uImage-dtb.omap4-panda-es Sending: Transfer complete mode, 5(SOH)/4438(STX)/0(CAN) packets, 3 retries ## Total Size = 0x00455950 = 4544848 Bytes Panda # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4544784 Bytes = 4.3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.12.0-rc4-23950-gd0e639c (paul@knihy) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Mon Oct 7 01:42:10 MDT 2013 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic OMAP4 (Flattened Device Tree), model: TI OMAP4 PandaBoard [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at ae800000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] On node 0 totalpages: 261888 [ 0.000000] free_area_init_node: node 0, pgdat c08bb3c0, node_mem_map c0e2b000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 528 pages used for memmap [ 0.000000] HighMem zone: 67328 pages, LIFO batch:15 [ 0.000000] OMAP4460 ES1.1 [ 0.000000] PERCPU: Embedded 9 pages/cpu @c1645000 s14016 r8192 d14656 u36864 [ 0.000000] pcpu-alloc: s14016 r8192 d14656 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260368 [ 0.000000] Kernel command line: console=ttyO2,230400n8 root=/dev/mmcblk0p2 rootwait vram=32M earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1007464K/1047552K available (5783K kernel code, 657K rwdata, 2084K rodata, 393K init, 5523K bss, 40088K reserved, 269312K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07b70d8 (7869 kB) [ 0.000000] .init : 0xc07b8000 - 0xc081a6c0 ( 394 kB) [ 0.000000] .data : 0xc081c000 - 0xc08c04c8 ( 658 kB) [ 0.000000] .bss : 0xc08c04c8 - 0xc0e25260 (5524 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] smp_twd: clock not found -2 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.000000] Calibrating local timer... 348.11MHz. [ 0.059783] Calibrating delay loop... 1384.44 BogoMIPS (lpj=6922240) [ 0.149261] pid_max: default: 32768 minimum: 301 [ 0.149841] Security Framework initialized [ 0.150024] Mount-cache hash table entries: 512 [ 0.164520] CPU: Testing write buffer coherency: ok [ 0.166076] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.166137] Setting up static identity map for 0xc057fc38 - 0xc057fca8 [ 0.166259] L310 cache controller enabled [ 0.166259] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e470000, Cache size: 1024 kB [ 0.170989] CPU1: Booted secondary processor [ 0.258728] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.259277] Brought up 2 CPUs [ 0.259277] SMP: Total of 2 processors activated. [ 0.259307] CPU: All CPU(s) started in SVC mode. [ 0.261840] devtmpfs: initialized [ 0.271240] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.340850] pinctrl core: initialized pinctrl subsystem [ 0.344055] regulator-dummy: no parameters [ 0.348815] NET: Registered protocol family 16 [ 0.355743] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.434234] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.435363] OMAP GPIO hardware version 0.1 [ 0.437133] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.439483] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.441680] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.443847] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.446044] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.447692] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.480285] No ATAGs? [ 0.480346] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.480346] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.484283] OMAP DMA hardware revision 0.0 [ 0.532714] bio: create slab at 0 [ 0.535675] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.535705] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 0.590789] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.591766] of_get_named_gpio_flags exited with status 62 [ 0.592712] hsusb1_reset: 3300 mV [ 0.593048] of_get_named_gpio_flags exited with status 1 [ 0.593566] hsusb1_vbus: 3300 mV [ 0.593933] reg-fixed-voltage wl12xx_vmmc.11: could not find pctldev for node /ocp/pinmux@4a31e040/pinmux_wl12xx_gpio, deferring probe [ 0.593963] platform wl12xx_vmmc.11: Driver reg-fixed-voltage requests probe deferral [ 0.599456] SCSI subsystem initialized [ 0.600982] usbcore: registered new interface driver usbfs [ 0.601318] usbcore: registered new interface driver hub [ 0.601745] usbcore: registered new device driver usb [ 0.604278] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 0.604339] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 0.604400] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 0.604431] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 0.604461] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 0.604492] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 0.604553] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 0.604583] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 0.611389] Switched to clocksource 32k_counter [ 0.733581] NET: Registered protocol family 2 [ 0.735382] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.735687] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.738403] TCP: Hash tables configured (established 8192 bind 8192) [ 0.738647] TCP: reno registered [ 0.738677] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.739044] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.740386] NET: Registered protocol family 1 [ 0.741729] RPC: Registered named UNIX socket transport module. [ 0.741760] RPC: Registered udp transport module. [ 0.741760] RPC: Registered tcp transport module. [ 0.741790] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.742645] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.743194] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.924072] bounce pool size: 64 pages [ 0.924713] VFS: Disk quotas dquot_6.5.2 [ 0.924926] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.927246] NFS: Registering the id_resolver key type [ 0.927642] Key type id_resolver registered [ 0.927673] Key type id_legacy registered [ 0.927764] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.928344] msgmni has been set to 1473 [ 0.931610] io scheduler noop registered [ 0.931610] io scheduler deadline registered [ 0.931701] io scheduler cfq registered (default) [ 0.933410] pinctrl-single 4a100040.pinmux: 203 pins at pa fc100040 size 406 [ 0.933959] pinctrl-single 4a31e040.pinmux: 28 pins at pa fc31e040 size 56 [ 0.937316] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.942413] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]' [ 0.943298] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 104, base_baud = 3000000) is a OMAP UART0 [ 0.944946] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]' [ 0.945281] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 105, base_baud = 3000000) is a OMAP UART1 [ 0.946258] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/serial@48020000[0]' [ 0.946624] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 106, base_baud = 3000000) is a OMAP UART2 [ 1.416809] console [ttyO2] enabled [ 1.420013] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/serial@4806e000[0]' [ 1.425354] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 102, base_baud = 3000000) is a OMAP UART3 [ 1.453643] brd: module loaded [ 1.468261] loop: module loaded [ 1.474792] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.488739] usbcore: registered new interface driver asix [ 1.492034] usbcore: registered new interface driver ax88179_178a [ 1.495666] usbcore: registered new interface driver cdc_ether [ 1.499176] usbcore: registered new interface driver r815x [ 1.502563] usbcore: registered new interface driver smsc95xx [ 1.506011] usbcore: registered new interface driver net1080 [ 1.509399] usbcore: registered new interface driver cdc_subset [ 1.513000] usbcore: registered new interface driver zaurus [ 1.516418] usbcore: registered new interface driver cdc_ncm [ 1.520904] usbcore: registered new interface driver cdc_wdm [ 1.524383] usbcore: registered new interface driver usb-storage [ 1.528015] usbcore: registered new interface driver usbtest [ 1.532745] mousedev: PS/2 mouse device common for all mice [ 1.539855] i2c /dev entries driver [ 1.542083] Driver for 1-wire Dallas network protocol. [ 1.546264] of_get_named_gpio_flags exited with status 86 [ 1.552795] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.558776] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.563507] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.568572] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.572631] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.576629] omap_hsmmc 4809c000.mmc: vmmc regulator missing [ 1.579925] omap-dma-engine 4a056000.dma-controller: freeing channel for 61 [ 1.583770] omap-dma-engine 4a056000.dma-controller: freeing channel for 62 [ 1.587646] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.591583] pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38) [ 1.595611] pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x [ 1.600402] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 1.605133] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 1.610015] omap-dma-engine 4a056000.dma-controller: allocating channel for 60 [ 1.614013] omap-dma-engine 4a056000.dma-controller: allocating channel for 59 [ 1.618011] omap_hsmmc 480d5000.mmc: vmmc regulator missing [ 1.621093] omap-dma-engine 4a056000.dma-controller: freeing channel for 59 [ 1.624938] omap-dma-engine 4a056000.dma-controller: freeing channel for 60 [ 1.628875] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.633605] of_get_named_gpio_flags exited with status 110 [ 1.636596] of_get_named_gpio_flags exited with status 8 [ 1.639526] of_get_named_gpio_flags exited with status 110 [ 1.643615] of_get_named_gpio_flags exited with status 8 [ 1.648101] ledtrig-cpu: registered to indicate activity on CPUs [ 1.652587] usbcore: registered new interface driver usbhid [ 1.655639] usbhid: USB HID core driver [ 1.658630] oprofile: using arm/armv7-ca9 [ 1.661437] TCP: cubic registered [ 1.663269] Initializing XFRM netlink socket [ 1.665679] NET: Registered protocol family 17 [ 1.668182] NET: Registered protocol family 15 [ 1.670898] Key type dns_resolver registered [ 1.674377] Power Management for TI OMAP4+ devices. [ 1.677093] Power Management for TI OMAP4. [ 1.679351] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.683197] ThumbEE CPU extension supported. [ 1.688659] of_get_named_gpio_flags exited with status 43 [ 1.692901] vwl1271: 1800 mV [ 1.701660] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.707916] twl 0-0048: PIH (irq 39) nested IRQs [ 1.712402] twl_rtc rtc.12: Power up reset detected. [ 1.716156] twl_rtc rtc.12: Enabling TWL-RTC [ 1.723266] twl_rtc rtc.12: rtc core: registered rtc.12 as rtc0 [ 1.728790] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.733886] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.738677] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.743743] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.748291] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.752777] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.757141] VDAC: 1800 mV [ 1.760162] VANA: 2100 mV [ 1.763641] VCXIO: 1800 mV [ 1.766693] VUSB: 3300 mV [ 1.770202] V1V8: 1800 mV [ 1.773895] V2V1: 2100 mV [ 1.782440] of_get_named_gpio_flags exited with status 127 [ 1.788787] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 1.794128] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 1.799743] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 1.804534] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 1.807708] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.812744] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.817596] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.821716] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.828552] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 1.871795] pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38) [ 1.876129] pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x [ 1.880920] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 1.885894] of_get_named_gpio_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 1.890777] omap-dma-engine 4a056000.dma-controller: allocating channel for 60 [ 1.894958] omap-dma-engine 4a056000.dma-controller: allocating channel for 59 [ 2.005065] twl_rtc rtc.12: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.012695] Waiting for root device /dev/mmcblk0p2... [ 2.270324] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.277557] mmc0: new high speed SD card at address 1234 [ 2.282531] mmcblk0: mmc0:1234 SA02G 1.83 GiB [ 2.290496] mmcblk0: p1 p2 [ 2.371978] kjournald starting. Commit interval 5 seconds [ 2.372283] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.372283] VFS: Mounted root (ext3 filesystem) readonly on device 179:2. [ 2.386108] devtmpfs: mounted [ 2.386108] Freeing unused kernel memory: 392K (c07b8000 - c081a000) /bin/sh: can't access tty; job control turned off / # / # / # / # / # %% Start PM consolidated quick test (retention only) %% Preparation / # / # mount -t sysfs none /sys / # / # mount -t debugfs none /debug / # / # / # / # for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d'  '`; do echo -1 > $u/power/autosuspend_delay_ms; done /bin/sh: paste: not found / # / # echo 0 > /debug/pm_debug/enable_off_mode / # / # %% Baseline pm_debug count dump cat /debug/pm_debug/count [ 9.404266] pwrdm state mismatch(ivahd_pwrdm) 3 != 1 [ 9.404266] pwrdm state mismatch(tesla_pwrdm) 3 != 1 [ 9.409790] pwrdm state mismatch(dss_pwrdm) 3 != 1 [ 9.412445] pwrdm state mismatch(abe_pwrdm) 3 != 1 cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:3,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (7) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # echo enabled > /sys/devices/44000000.ocp/48020000.serial/tty/ttyO2/power/wak eup / # %% Start retention double suspend/resume UART wakeup test echo mem > /sys/power/state [ 11.610839] PM: Syncing filesystems ... done. [ 11.613342] PM: Preparing system for mem sleep [ 11.623504] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 11.623504] Freezing remaining freezable tasks ... (elapsed 0.008 seconds) done. [ 11.631591] PM: Entering mem sleep [ 11.635101] Suspending console(s) (use no_console_suspend to debug) [ 11.654144] PM: suspend of devices complete after 12.786 msecs [ 11.658050] PM: late suspend of devices complete after 3.906 msecs [ 11.662628] PM: noirq suspend of devices complete after 4.577 msecs [ 11.662628] Disabling non-boot CPUs ... [ 11.666564] CPU1: shutdown [ 11.667785] Successfully put all powerdomains to target state [ 11.667785] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 11.667816] Enabling non-boot CPUs ... [ 11.670562] CPU1: Booted secondary processor [ 11.671722] CPU1 is up [ 11.674255] PM: noirq resume of devices complete after 2.532 msecs [ 11.675323] PM: early resume of devices complete after 1.068 msecs [ 12.076873] PM: resume of devices complete after 401.458 msecs [ 12.111541] PM: Finishing wakeup. [ 12.120056] Restarting tasks ... done. / # / # / # / # cat /debug/pm_debug/count cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:6,INA:0,ON:6,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:1,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:1 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (7) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # / # / # echo mem > /sys/power/state [ 14.871978] PM: Syncing filesystems ... done. [ 14.875091] PM: Preparing system for mem sleep [ 14.879425] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 14.883422] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done. [ 14.888366] PM: Entering mem sleep [ 14.891937] Suspending console(s) (use no_console_suspend to debug) [ 14.908416] PM: suspend of devices complete after 16.296 msecs [ 14.911254] PM: late suspend of devices complete after 2.838 msecs [ 14.916534] PM: noirq suspend of devices complete after 5.279 msecs [ 14.916534] Disabling non-boot CPUs ... [ 14.918212] CPU1: shutdown [ 14.919555] Successfully put all powerdomains to target state [ 14.919555] hw-breakpoint: CPU 0 failed to disable vector catch [ 14.919586] Enabling non-boot CPUs ... [ 14.922088] CPU1: Booted secondary processor [ 14.922851] CPU1 is up [ 14.925354] PM: noirq resume of devices complete after 2.410 msecs [ 14.925354] PM: early resume of devices complete after 0.001 msecs [ 15.901062] PM: resume of devices complete after 971.923 msecs [ 15.941833] PM: Finishing wakeup. [ 15.941833] Restarting tasks ... done. / # / # / # / # cat /debug/pm_debug/count cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:9,INA:0,ON:9,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:2,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:2 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (7) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # / # / # ./test_rootfs_access_nonexistent_file__ret_susp /bin/sh: ./test_rootfs_access_nonexistent_file__ret_susp: not found / # / # %% End retention double suspend/resume UART wakeup test %% Start retention dynamic idle UART wakeup test for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d'  '`; do echo 3000 > $u/power/autosuspend_delay_ms; done /bin/sh: paste: not found / # / # / # / # / # / # cat /debug/pm_debug/count cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:9,INA:0,ON:9,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:2,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:2 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (7) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # / # / # ./test_rootfs_access_nonexistent_file__ret_dyn /bin/sh: ./test_rootfs_access_nonexistent_file__ret_dyn: not found / # / # for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d'  '`; do echo -1 > $u/power/autosuspend_delay_ms; done /bin/sh: paste: not found / # / # %% End retention dynamic idle UART wakeup test %% End PM consolidated quick test (retention only)