CCSending /srv/serial/u-boot-spl.bin, 784 blocks: Give your local XMODEM receive command now. Transfer complete t SPL 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 CSending: u-boot.bin Sending: Transfer complete , 3(SOH)/375(STX)/0(CAN) packets, 3 retries Loaded 384084 bytes U-Boot 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 mmc_send_cmd : timeout: No status update Card did not respond to voltage select! mmc0(part 0) is current device mmc_send_cmd : timeout: No status update Card did not respond to voltage select! Booting from nand ... no devices available Wrong Image Format for bootm command ERROR: can't get kernel image! U-Boot# a askenv - get environment variables from stdin Usage: askenv name [message] [size] - get environment variable 'name' from stdin (max 'size' chars) U-Boot# setenv autoload off; setenv serverip 192.168.57.1; dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.138 U-Boot# tftp 0x81000000 zImage.omap2plus_defconfig link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'zImage.omap2plus_defconfig'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################### 919.9 KiB/s done Bytes transferred = 4264376 (4111b8 hex) U-Boot# tftp 0x82000000 am335x-bone.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'am335x-bone.dtb'. Load address: 0x82000000 Loading: *## 930.7 KiB/s done Bytes transferred = 28596 (6fb4 hex) U-Boot# setenv bootargs console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp U-Boot# U-Boot# bootz 0x81000000 - 0x82000000 ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 82000000, end 82009fb3 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.14.0-rc1-49348-g38dbfb5 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Mon Feb 10 03:59:22 MST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at 8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c088a240, node_mem_map cfcf2000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @cfcd8000 s14016 r8192 d14656 u36864 [ 0.000000] pcpu-alloc: s14016 r8192 d14656 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 228036K/261120K available (5561K kernel code, 654K rwdata, 2128K rodata, 385K init, 5518K bss, 33084K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc078a8dc (7691 kB) [ 0.000000] .init : 0xc078b000 - 0xc07eb6c0 ( 386 kB) [ 0.000000] .data : 0xc07ec000 - 0xc088f818 ( 655 kB) [ 0.000000] .bss : 0xc088f818 - 0xc0df33b8 (5519 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000025] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000053] OMAP clocksource: timer1 at 24000000 Hz [ 0.001260] Console: colour dummy device 80x30 [ 0.001341] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001357] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001370] ... MAX_LOCK_DEPTH: 48 [ 0.001383] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001397] ... CLASSHASH_SIZE: 4096 [ 0.001409] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.001422] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.001435] ... CHAINHASH_SIZE: 16384 [ 0.001448] memory used by lock dependency info: 3695 kB [ 0.001461] per task-struct memory footprint: 1152 bytes [ 0.001530] Calibrating delay loop... 545.58 BogoMIPS (lpj=2727936) [ 0.098704] pid_max: default: 32768 minimum: 301 [ 0.099340] Security Framework initialized [ 0.099530] Mount-cache hash table entries: 512 [ 0.129754] CPU: Testing write buffer coherency: ok [ 0.131635] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.131730] Setting up static identity map for 0x80545760 - 0x805457d0 [ 0.136599] Brought up 1 CPUs [ 0.136624] SMP: Total of 1 processors activated. [ 0.136640] CPU: All CPU(s) started in SVC mode. [ 0.141142] devtmpfs: initialized [ 0.156145] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.217882] omap_hwmod: tptc0 using broken dt data from edma [ 0.218530] omap_hwmod: tptc1 using broken dt data from edma [ 0.219230] omap_hwmod: tptc2 using broken dt data from edma [ 0.230508] omap_hwmod: debugss: _wait_target_disable failed [ 0.295729] pinctrl core: initialized pinctrl subsystem [ 0.302157] regulator-dummy: no parameters [ 0.306983] NET: Registered protocol family 16 [ 0.316215] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.345597] platform 49000000.edma: alias fck already exists [ 0.345655] platform 49000000.edma: alias fck already exists [ 0.345688] platform 49000000.edma: alias fck already exists [ 0.350818] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.352632] OMAP GPIO hardware version 0.1 [ 0.356383] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.360925] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.365103] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.391116] No ATAGs? [ 0.391150] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.491203] bio: create slab at 0 [ 0.554482] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.555893] of_get_named_gpiod_flags: can't parse gpios property of node '/fixedregulator@0[0]' [ 0.557542] vmmcsd_fixed: 3300 mV [ 0.568366] SCSI subsystem initialized [ 0.573251] usbcore: registered new interface driver usbfs [ 0.573985] usbcore: registered new interface driver hub [ 0.575091] usbcore: registered new device driver usb [ 0.580234] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 0.580306] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.592424] Switched to clocksource timer1 [ 0.853885] NET: Registered protocol family 2 [ 0.856486] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.856750] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.858002] TCP: Hash tables configured (established 2048 bind 2048) [ 0.858271] TCP: reno registered [ 0.858315] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.858660] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.860415] NET: Registered protocol family 1 [ 0.862835] RPC: Registered named UNIX socket transport module. [ 0.862868] RPC: Registered udp transport module. [ 0.862884] RPC: Registered tcp transport module. [ 0.862901] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.864748] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.879186] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.114425] VFS: Disk quotas dquot_6.5.2 [ 1.114779] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.117975] NFS: Registering the id_resolver key type [ 1.118558] Key type id_resolver registered [ 1.118589] Key type id_legacy registered [ 1.118771] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.119452] msgmni has been set to 477 [ 1.124885] io scheduler noop registered [ 1.124918] io scheduler deadline registered [ 1.125013] io scheduler cfq registered (default) [ 1.129504] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 1.135985] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.148111] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@44e09000[0]' [ 1.149977] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.886332] console [ttyO0] enabled [ 1.897791] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 1.954713] brd: module loaded [ 1.990411] loop: module loaded [ 2.003974] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.023641] usbcore: registered new interface driver asix [ 2.029994] usbcore: registered new interface driver ax88179_178a [ 2.037938] usbcore: registered new interface driver cdc_ether [ 2.045954] usbcore: registered new interface driver r815x [ 2.052698] usbcore: registered new interface driver smsc95xx [ 2.059381] usbcore: registered new interface driver net1080 [ 2.066140] usbcore: registered new interface driver cdc_subset [ 2.073358] usbcore: registered new interface driver zaurus [ 2.079990] usbcore: registered new interface driver cdc_ncm [ 2.089070] usbcore: registered new interface driver cdc_wdm [ 2.096023] usbcore: registered new interface driver usb-storage [ 2.103552] usbcore: registered new interface driver usbtest [ 2.115349] mousedev: PS/2 mouse device common for all mice [ 2.129023] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 2.139026] i2c /dev entries driver [ 2.143811] Driver for 1-wire Dallas network protocol. [ 2.156739] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.168442] of_get_named_gpiod_flags exited with status 0 [ 2.174387] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@48060000[0]' [ 2.184930] omap_hsmmc 48060000.mmc: vmmc regulator missing [ 2.191467] platform 48060000.mmc: Driver omap_hsmmc requests probe deferral [ 2.202487] usbcore: registered new interface driver usbhid [ 2.208340] usbhid: USB HID core driver [ 2.215692] oprofile: using arm/armv7 [ 2.220570] TCP: cubic registered [ 2.224193] Initializing XFRM netlink socket [ 2.228849] NET: Registered protocol family 17 [ 2.233701] NET: Registered protocol family 15 [ 2.238831] Key type dns_resolver registered [ 2.246598] ThumbEE CPU extension supported. [ 2.276453] DCDC1: at 1500 mV [ 2.284105] vdd_mpu: 925 <--> 1325 mV at 1100 mV [ 2.292235] vdd_core: 925 <--> 1150 mV at 1100 mV [ 2.300566] LDO1: at 1800 mV [ 2.306946] LDO2: at 3300 mV [ 2.313433] LDO3: 1800 <--> 3300 mV at 1800 mV [ 2.321111] LDO4: at 3300 mV [ 2.327615] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 2.333559] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.340554] of_get_named_gpiod_flags exited with status 0 [ 2.346395] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@48060000[0]' [ 2.358034] 48060000.mmc supply vmmc_aux not found, using dummy regulator [ 2.472385] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.478798] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.488859] libphy: 4a101000.mdio: probed [ 2.493250] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.505951] Detected MACID = 78:c5:e5:c3:1e:2a [ 2.518213] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 2.558982] net eth0: initializing cpsw version 1.12 (0) [ 2.643371] net eth0: phy found : id is : 0x7c0f1 [ 2.648513] libphy: PHY 4a101000.mdio:01 not found [ 2.653624] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 5.722915] libphy: 4a101000.mdio:00 - Link is Up - 100/Full [ 5.742393] Sending DHCP requests ., OK [ 5.852820] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.138 [ 5.861660] IP-Config: Complete: [ 5.865162] device=eth0, hwaddr=78:c5:e5:c3:1e:2a, ipaddr=192.168.57.138, mask=255.255.255.0, gw=255.255.255.255 [ 5.876355] host=192.168.57.138, domain=example.org, nis-domain=(none) [ 5.883705] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.890448] nameserver0=192.168.57.1 [ 5.897251] omap_uart 44e09000.serial: no wakeirq for uart0 [ 5.927375] VFS: Mounted root (nfs filesystem) on device 0:12. [ 5.935888] devtmpfs: mounted [ 5.940079] Freeing unused kernel memory: 384K (c078b000 - c07eb000) [ 6.448875] omap_uart 44e09000.serial: no wakeirq for uart0 [ 6.464273] omap_uart 44e09000.serial: no wakeirq for uart0 INIT: [ 6.483258] omap_uart 44e09000.serial: no wakeirq for uart0 version 2.88 booting[ 6.503147] omap_uart 44e09000.serial: no wakeirq for uart0 [ 6.534210] omap_uart 44e09000.serial: no wakeirq for uart0 [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.884437] udevd[724]: starting version 175 [ ok . [....] Synthesizing the initial hotplug events...udevd[765]: error changing net interface name eth0 to eth4: Device or resource busy [ ok done. [....] Waiting for /dev to be fully populated...[ ok done. [....] Activating swap...[ ok done. [ 16.108351] random: nonblocking pool is initialized [....] Cleaning up temporary files... /tmp[ ok . [....] Activating lvm and md swap...[ ok done. [....] Checking file systems...fsck from util-linux 2.20.1 [ ok done. [....] Mounting local filesystems...[ ok done. [....] Activating swapfile swap...[ ok done. [....] Cleaning up temporary files...[ ok . [....] Setting kernel variables ...[ ok done. [....] Configuring network interfaces...[ ok done. [....] Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 [ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [....] Cleaning up temporary files...[ ok . [....] Starting network benchmark server[ ok . [ 34.685965] omap_uart 44e09000.serial: no wakeirq for uart0 INIT: [ 34.713183] omap_uart 44e09000.serial: no wakeirq for uart0 Entering runlevel: 2[ 34.733134] omap_uart 44e09000.serial: no wakeirq for uart0 [ 34.764774] omap_uart 44e09000.serial: no wakeirq for uart0 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting network benchmark server[FAIL failed! [....] Starting system message bus: dbus[ ok . [....] Starting rpcbind daemon...[....] Already running.[ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [ 39.146024] omap_uart 44e09000.serial: no wakeirq for uart0 Debian GNU/Linux wheezy/sid armel ttyO0 armel login: