Texas Instruments X-Loader 1.47 (Jan 14 2011 - 15:43:28) Starting X-loader on MMC Reading boot sector 212836 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... U-Boot 2010.06 (Jan 14 2011 - 15:43:45) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 EVM board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB In: serial Out: serial Err: serial Read back SMSC id 0x92200000 Die ID #368000229ff80000016071640902c013 Net: smc911x-0 Hit any key to stop autoboot: 3  2  1  0 OMAP3_EVM # OMAP3_EVM # setenv bootfile uImage-dtb.omap3-evm-37xx OMAP3_EVM # OMAP3_EVM # dhcp smc911x: detected LAN9220 controller smc911x: phy initialized smc911x: MAC 00:50:c2:7e:99:42 BOOTP broadcast 1 DHCP client bound to address 192.168.57.131 Using smc911x-0 device TFTP from server 192.168.57.1; our IP address is 192.168.57.131 Filename 'uImage-dtb.omap3-evm-37xx'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### done Bytes transferred = 4348671 (425aff hex) OMAP3_EVM # setenv bootargs console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh OMAP3_EVM # OMAP3_EVM # bootm ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4348607 Bytes = 4.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.15.0-rc1-64222-gc9eaa44 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Mon Apr 21 11:38:09 MDT 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP37XX EVM (TMDSEVM3730) [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at 8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c08946c0, node_mem_map cfcf2000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @cfca8000 s14080 r8192 d14592 u36864 [ 0.000000] pcpu-alloc: s14080 r8192 d14592 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 227764K/261120K available (5572K kernel code, 663K rwdata, 2144K rodata, 389K init, 5522K bss, 33356K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc079134c (7717 kB) [ 0.000000] .init : 0xc0792000 - 0xc07f3700 ( 390 kB) [ 0.000000] .data : 0xc07f4000 - 0xc0899ec0 ( 664 kB) [ 0.000000] .bss : 0xc0899ec0 - 0xc0dfea90 (5523 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001129] Console: colour dummy device 80x30 [ 0.001220] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001220] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001251] ... MAX_LOCK_DEPTH: 48 [ 0.001251] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001251] ... CLASSHASH_SIZE: 4096 [ 0.001281] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.001281] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.001312] ... CHAINHASH_SIZE: 16384 [ 0.001312] memory used by lock dependency info: 3695 kB [ 0.001342] per task-struct memory footprint: 1152 bytes [ 0.001373] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696) [ 0.107666] pid_max: default: 32768 minimum: 301 [ 0.108276] Security Framework initialized [ 0.108489] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.108489] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.111907] CPU: Testing write buffer coherency: ok [ 0.113494] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.113555] Setting up static identity map for 0x80548050 - 0x805480c0 [ 0.118072] Brought up 1 CPUs [ 0.118072] SMP: Total of 1 processors activated. [ 0.118103] CPU: All CPU(s) started in SVC mode. [ 0.121948] devtmpfs: initialized [ 0.132598] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.211486] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.213714] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.243316] omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm [ 0.245697] omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm [ 0.320983] pinctrl core: initialized pinctrl subsystem [ 0.324676] regulator-dummy: no parameters [ 0.417480] NET: Registered protocol family 16 [ 0.426147] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.441009] Reprogramming SDRC clock to 400000000 Hz [ 0.453491] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.454772] OMAP GPIO hardware version 2.5 [ 0.456512] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.459442] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.462127] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.464752] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.467468] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.492950] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 0.494445] gpmc_probe_nand_child: ti,elm-id property not found [ 0.494659] gpmc_cs_program_settings: invalid width 0! [ 0.500274] No ATAGs?[ 0.500305] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.504241] OMAP DMA hardware revision 5.0 [ 0.543914] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.544006] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 0.598266] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.599426] of_get_named_gpiod_flags: can't parse gpios property of node '/regulator-vddvario[0]' [ 0.600341] vddvario: no parameters [ 0.600921] of_get_named_gpiod_flags: can't parse gpios property of node '/regulator-vdd33a[0]' [ 0.601501] vdd33a: no parameters [ 0.602142] reg-fixed-voltage wl12xx_vmmc.6: could not find pctldev for node /ocp/pinmux@48002030/pinmux_wl12xx_gpio, deferring probe [ 0.602172] platform wl12xx_vmmc.6: Driver reg-fixed-voltage requests probe deferral [ 0.607818] SCSI subsystem initialized [ 0.608978] usbcore: registered new interface driver usbfs [ 0.609252] usbcore: registered new interface driver hub [ 0.623229] usbcore: registered new device driver usb [ 0.754486] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz [ 0.756134] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz [ 0.760833] omap_i2c 48060000.i2c: bus 2 rev4.4 at 400 kHz [ 0.768432] Switched to clocksource 32k_counter [ 0.979095] NET: Registered protocol family 2 [ 0.981445] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.981689] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.982849] TCP: Hash tables configured (established 2048 bind 2048) [ 0.983032] TCP: reno registered [ 0.983062] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.983398] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.984985] NET: Registered protocol family 1 [ 0.987609] RPC: Registered named UNIX socket transport module. [ 0.987640] RPC: Registered udp transport module. [ 0.987640] RPC: Registered tcp transport module. [ 0.987670] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.989349] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.997131] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.213958] VFS: Disk quotas dquot_6.5.2 [ 1.214141] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.217468] NFS: Registering the id_resolver key type [ 1.218017] Key type id_resolver registered [ 1.218048] Key type id_legacy registered [ 1.218231] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.218872] msgmni has been set to 476 [ 1.226562] io scheduler noop registered [ 1.226593] io scheduler deadline registered [ 1.226715] io scheduler cfq registered (default) [ 1.230010] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568 [ 1.230712] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92 [ 1.231781] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size 92 [ 1.234954] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV [ 1.236755] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.247131] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.247161] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]' [ 1.248962] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 2.109802] console [ttyO0] enabled [ 2.115814] omap_uart 4806c000.serial: no wakeirq for uart0 [ 2.121826] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]' [ 2.135833] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 2.149841] omap_uart 49020000.serial: no wakeirq for uart0 [ 2.155761] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@49020000[0]' [ 2.166503] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 2.181243] omap_uart 49042000.serial: no wakeirq for uart0 [ 2.187255] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@49042000[0]' [ 2.201904] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3 [ 2.249999] brd: module loaded [ 2.276733] loop: module loaded [ 2.299621] twl 0-0048: PIH (irq 23) chaining IRQs 338..346 [ 2.306121] twl 0-0048: power (irq 343) chaining IRQs 346..353 [ 2.320861] VAUX1: at 3000 mV [ 2.332336] VAUX2_4030: at 1800 mV [ 2.340057] VAUX3: at 2800 mV [ 2.348144] VAUX4: at 2800 mV [ 2.355224] VDD1: 600 <--> 1450 mV at 1200 mV [ 2.364990] VDAC: 1800 mV [ 2.374786] VIO: at 1800 mV [ 2.383026] VINTANA1: 1500 mV [ 2.391265] VINTANA2: at 2750 mV [ 2.400085] VINTDIG: 1500 mV [ 2.406280] VMMC1: 1850 <--> 3150 mV at 3000 mV [ 2.416107] VMMC2: 1850 <--> 3150 mV at 2600 mV [ 2.424896] VUSB1V5: 1500 mV [ 2.430603] VUSB1V8: 1800 mV [ 2.435729] VUSB3V1: 3100 mV [ 2.443450] VPLL1: at 1800 mV [ 2.451232] VPLL2: 1800 mV [ 2.457702] VSIM: 1800 <--> 3000 mV at 1800 mV [ 2.467742] twl4030_gpio twl4030-gpio: gpio (irq 338) chaining IRQs 354..371 [ 2.476348] gpiochip_find_base: found new base at 492 [ 2.482910] gpiochip_add: registered GPIOs 492 to 511 on device: twl4030 [ 2.497924] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.548126] libphy: smsc911x-mdio: probed [ 2.627777] smsc911x 2c000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=2c000000.etherne:01, irq=-1) [ 2.640197] smsc911x 2c000000.ethernet eth0: MAC Address: 00:50:c2:7e:99:42 [ 2.649475] usbcore: registered new interface driver asix [ 2.655364] usbcore: registered new interface driver ax88179_178a [ 2.662109] usbcore: registered new interface driver cdc_ether [ 2.668579] usbcore: registered new interface driver smsc95xx [ 2.674804] usbcore: registered new interface driver net1080 [ 2.680999] usbcore: registered new interface driver cdc_subset [ 2.687469] usbcore: registered new interface driver zaurus [ 2.693664] usbcore: registered new interface driver cdc_ncm [ 2.701354] usbcore: registered new interface driver cdc_wdm [ 2.707702] usbcore: registered new interface driver usb-storage [ 2.714294] usbcore: registered new interface driver usbtest [ 2.723510] mousedev: PS/2 mouse device common for all mice [ 2.730834] twl4030_keypad keypad.32: OF: linux,keymap property not defined in /ocp/i2c@48070000/twl@48/keypad [ 2.741516] twl4030_keypad keypad.32: Failed to build keymap [ 2.747650] twl4030_keypad: probe of keypad.32 failed with error -2 [ 2.758636] input: twl4030_pwrbutton as /devices/68000000.ocp/48070000.i2c/i2c-0/0-0048/pwrbutton.31/input/input1 [ 2.773712] twl_rtc rtc.7: Power up reset detected. [ 2.779785] twl_rtc rtc.7: Enabling TWL-RTC [ 2.792510] twl_rtc rtc.7: rtc core: registered rtc.7 as rtc0 [ 2.801574] i2c /dev entries driver [ 2.809692] Driver for 1-wire Dallas network protocol. [ 2.821350] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.832672] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.842010] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.907653] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 2.916870] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 2.926727] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 [ 2.934356] platform 480b4000.mmc: Driver omap_hsmmc requests probe deferral [ 2.943206] usbcore: registered new interface driver usbhid [ 2.949188] usbhid: USB HID core driver [ 2.955139] oprofile: using arm/armv7 [ 2.959777] TCP: cubic registered [ 2.963287] Initializing XFRM netlink socket [ 2.968048] NET: Registered protocol family 17 [ 2.972839] NET: Registered protocol family 15 [ 2.978027] Key type dns_resolver registered [ 2.984649] ThumbEE CPU extension supported. [ 2.989318] Registering SWP/SWPB emulation handler [ 3.012939] VUSB3V1: disabling [ 3.020233] of_get_named_gpiod_flags exited with status 0 [ 3.027648] vwl1271: 1800 mV [ 3.031036] vwl1271: supplied by VMMC2 [ 3.036621] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 3.046051] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 3.171661] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.184692] mmc0: new SDHC card at address e624 [ 3.192871] mmcblk0: mmc0:e624 SD08G 7.40 GiB [ 3.199432] twl_rtc rtc.7: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.384552] smsc911x 2c000000.ethernet eth0: SMSC911x/921x identified at 0xd087c000, IRQ: 288 [ 3.407531] Sending DHCP requests . [ 3.412353] mmcblk0: p1 p2 p3 [ 6.347259] ., OK [ 6.367767] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.131 [ 6.376770] IP-Config: Complete: [ 6.380310] device=eth0, hwaddr=00:50:c2:7e:99:42, ipaddr=192.168.57.131, mask=255.255.255.0, gw=255.255.255.255 [ 6.391571] host=192.168.57.131, domain=example.org, nis-domain=(none) [ 6.398986] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 6.405761] nameserver0=192.168.57.1 [ 6.435424] VFS: Mounted root (nfs filesystem) readonly on device 0:12. [ 6.444793] devtmpfs: mounted [ 6.449096] Freeing unused kernel memory: 388K (c0792000 - c07f3000) /bin/sh: 0: can't access tty; job control turned off # %% Start PM consolidated quick test %% Preparation # # mount -t sysfs none /sys # # mount -t debugfs none /debug # # # # for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d' '`; do echo -1 > $u/power/autosuspend_delay_ms; done # # echo 0 > /debug/pm_debug/enable_off_mode # # %% Baseline pm_debug count dump cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:458,INA:0,ON:459,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:458,INA:0,ON:459,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:458,INA:0,ON:459,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:458,INA:0,ON:459,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (1) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (15) cam_clkdm->cam_pwrdm (0) dss_clkdm->dss_pwrdm (1) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (22) core_l3_clkdm->core_pwrdm (1) neon_clkdm->neon_pwrdm (0) # # echo enabled > /sys/devices/44000000.ocp/48020000.serial/tty/ttyO2/power/wakeup /bin/sh: 15: cannot create /sys/devices/44000000.ocp/48020000.serial/tty/ttyO2/power/wakeup: Directory nonexistent # %% Start retention double suspend/resume UART wakeup test echo mem > /sys/power/state [ 13.559722] PM: Syncing filesystems ... done. [ 13.566925] PM: Preparing system for mem sleep [ 13.579956] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 13.587677] Freezing remaining freezable tasks ... (elapsed 0.003 seconds) done. [ 13.599029] PM: Entering mem sleep [ 13.602630] Suspending console(s) (use no_console_suspend to debug) [ 13.632629] PM: suspend of devices complete after 18.402 msecs [ 13.640411] PM: late suspend of devices complete after 7.781 msecs [ 13.649017] PM: noirq suspend of devices complete after 8.605 msecs [ 13.649108] Disabling non-boot CPUs ... [ 13.649230] Successfully put all powerdomains to target state [ 13.654022] PM: noirq resume of devices complete after 4.699 msecs [ 13.660369] PM: early resume of devices complete after 5.218 msecs [ 13.849456] PM: resume of devices complete after 189.025 msecs [ 13.904632] PM: Finishing wakeup. [ 13.908172] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:569,INA:0,ON:570,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:569,INA:0,ON:570,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:569,INA:0,ON:570,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:569,INA:0,ON:570,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (1) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (15) cam_clkdm->cam_pwrdm (0) dss_clkdm->dss_pwrdm (1) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (26) core_l3_clkdm->core_pwrdm (1) neon_clkdm->neon_pwrdm (0) # # # # echo mem > /sys/power/state [ 15.853332] PM: Syncing filesystems ... done. [ 15.858642] PM: Preparing system for mem sleep [ 15.865356] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 15.872985] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 15.882843] PM: Entering mem sleep [ 15.886413] Suspending console(s) (use no_console_suspend to debug) [ 15.911437] PM: suspend of devices complete after 13.549 msecs [ 15.919128] PM: late suspend of devices complete after 7.690 msecs [ 15.927276] PM: noirq suspend of devices complete after 8.087 msecs [ 15.927307] Disabling non-boot CPUs ... [ 15.927398] Successfully put all powerdomains to target state [ 15.932067] PM: noirq resume of devices complete after 4.638 msecs [ 15.938354] PM: early resume of devices complete after 5.187 msecs [ 16.129333] PM: resume of devices complete after 190.887 msecs [ 16.184020] PM: Finishing wakeup. [ 16.187591] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:674,INA:0,ON:675,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:674,INA:0,ON:675,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:674,INA:0,ON:675,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:674,INA:0,ON:675,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (1) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (15) cam_clkdm->cam_pwrdm (0) dss_clkdm->dss_pwrdm (1) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (22) core_l3_clkdm->core_pwrdm (1) neon_clkdm->neon_pwrdm (0) # # # # ./test_rootfs_access_nonexistent_file__ret_susp /bin/sh: 32: ./test_rootfs_access_nonexistent_file__ret_susp: not found # # %% End retention double suspend/resume UART wakeup test %% Start retention dynamic idle UART wakeup test for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d' '`; do echo 3000 > $u/power/autosuspend_delay_ms; done # #