U-Boot 1.1.4 (Mar 18 2007 - 12:22:00)

OMAP2430C-GP revision 3, PRCM #5A
TI 2430SDP 1.1 Version + mDDR (Boot NOR)
DRAM:  128 MB
Flash: 192 MB
NAND:64 MB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  3  0 
OMAP243X SDP # 
OMAP243X SDP # setenv bootargs console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh
OMAP243X SDP # loady
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CSending: uImage-dtb.omap2430-sdp
Sending: 

Transfer complete
m - CRC mode, 4(SOH)/4203(STX)/0(CAN) packets, 3 retries
## Total Size      = 0x0041acbb = 4304059 Bytes
OMAP243X SDP # bootm
## Booting image at 80000000 ...
   Image Name:   Linux-
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4303995 Bytes =  4.1 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.15.0-rc7-15519-gc720816 (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed May 28 12:12:29 MDT 2014
[    0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d
[    0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: TI OMAP2430 SDP
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] cma: CMA: reserved 16 MiB at 86800000
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 32512
[    0.000000] free_area_init_node: node 0, pgdat c0898700, node_mem_map c7df2000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32512 pages, LIFO batch:7
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] OMAP2430
[    0.000000] 
[    0.000000] PERCPU: Embedded 9 pages/cpu @c7dda000 s14080 r8192 d14592 u36864
[    0.000000] pcpu-alloc: s14080 r8192 d14592 u36864 alloc=9*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32256
[    0.000000] Kernel command line: console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 98052K/130048K available (5576K kernel code, 663K rwdata, 2148K rodata, 393K init, 5522K bss, 31996K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0793384   (7725 kB)
[    0.000000]       .init : 0xc0794000 - 0xc07f6700   ( 394 kB)
[    0.000000]       .data : 0xc07f8000 - 0xc089df00   ( 664 kB)
[    0.000000]        .bss : 0xc089df00 - 0xc0e02a98   (5523 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns
[    0.000061] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000518] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present.
[    0.002777] Console: colour dummy device 80x30
[    0.002960] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.002990] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.003021] ... MAX_LOCK_DEPTH:          48
[    0.003051] ... MAX_LOCKDEP_KEYS:        8191
[    0.003082] ... CLASSHASH_SIZE:          4096
[    0.003112] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.003143] ... MAX_LOCKDEP_CHAINS:      32768
[    0.003143] ... CHAINHASH_SIZE:          16384
[    0.003173]  memory used by lock dependency info: 3695 kB
[    0.003204]  per task-struct memory footprint: 1152 bytes
[    0.003356] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
[    0.128479] pid_max: default: 32768 minimum: 301
[    0.129913] Security Framework initialized
[    0.130371] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.130432] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.139923] CPU: Testing write buffer coherency: ok
[    0.144409] missing device node for CPU 0
[    0.144470] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366
[    0.144622] Setting up static identity map for 0x80549150 - 0x805491c0
[    0.156494] Brought up 1 CPUs
[    0.156524] SMP: Total of 1 processors activated.
[    0.156555] CPU: All CPU(s) started in SVC mode.
[    0.167480] devtmpfs: initialized
[    0.193511] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2
[    0.243133] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3)
[    0.274108] pinctrl core: initialized pinctrl subsystem
[    0.284301] regulator-dummy: no parameters
[    0.329437] NET: Registered protocol family 16
[    0.353454] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.423034] omap_gpio 4900c000.gpio: Could not get gpio dbck
[    0.426635] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[    0.430023] OMAP GPIO hardware version 2.4
[    0.432739] omap_gpio 4900e000.gpio: Could not get gpio dbck
[    0.434051] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[    0.439392] omap_gpio 49010000.gpio: Could not get gpio dbck
[    0.440521] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[    0.445739] omap_gpio 49012000.gpio: Could not get gpio dbck
[    0.447113] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[    0.452575] omap_gpio 480b6000.gpio: Could not get gpio dbck
[    0.453704] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
[    0.459381] omap-gpmc 6e000000.gpmc: GPMC revision 3.0
[    0.460357] omap-gpmc 6e000000.gpmc: ethernet using bootloader timings on CS5
[    0.473632] No ATAGs?
[    0.473785] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[    0.473846] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.480895] OMAP DMA hardware revision 4.0
[    0.574127] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot
[    0.574340] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5
[    0.708007] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver
[    0.722167] SCSI subsystem initialized
[    0.724975] usbcore: registered new interface driver usbfs
[    0.725677] usbcore: registered new interface driver hub
[    0.728088] usbcore: registered new device driver usb
[    0.736114] omap_i2c 48070000.i2c: bus 0 rev3.3 at 100 kHz
[    1.123626] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz
[    1.141326] Switched to clocksource 32k_counter
[    1.665191] NET: Registered protocol family 2
[    1.671447] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.671997] TCP bind hash table entries: 1024 (order: 3, 36864 bytes)
[    1.673370] TCP: Hash tables configured (established 1024 bind 1024)
[    1.673889] TCP: reno registered
[    1.673980] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    1.674743] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    1.678741] NET: Registered protocol family 1
[    1.684936] RPC: Registered named UNIX socket transport module.
[    1.684997] RPC: Registered udp transport module.
[    1.685058] RPC: Registered tcp transport module.
[    1.685089] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.689727] hw perfevents: enabled with v6 PMU driver, 3 counters available
[    1.707702] futex hash table entries: 256 (order: 2, 16384 bytes)
[    2.400573] VFS: Disk quotas dquot_6.5.2
[    2.401000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.413116] NFS: Registering the id_resolver key type
[    2.414672] Key type id_resolver registered
[    2.414733] Key type id_legacy registered
[    2.415161] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    2.417297] msgmni has been set to 223
[    2.436584] io scheduler noop registered
[    2.436645] io scheduler deadline registered
[    2.436889] io scheduler cfq registered (default)
[    2.445739] pinctrl-single 49002030.pinmux: 340 pins at pa fb002030 size 340
[    2.453826] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV 
[    2.457000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.486358] omap_uart 4806a000.serial: no wakeirq for uart0
[    2.486450] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]'
[    2.493896] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[    3.295532] console [ttyO0] enabled
[    3.304687] omap_uart 4806c000.serial: no wakeirq for uart0
[    3.310821] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]'
[    3.323028] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    3.343933] omap_uart 4806e000.serial: no wakeirq for uart0
[    3.350067] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806e000[0]'
[    3.373809] 4806e000.serial: ttyO2 at MMIO 0x4806e000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[    3.396240] omap_rng 480a0000.rng: OMAP Random Number Generator ver. 50
[    3.513885] brd: module loaded
[    3.581085] loop: module loaded
[    3.655090] twl 1-0048: PIH (irq 23) chaining IRQs 274..282
[    3.662475] twl 1-0048: power (irq 279) chaining IRQs 282..289
[    3.693939] VAUX1: at 3000 mV 
[    3.709869] VAUX2_4030: at 2800 mV 
[    3.725555] VAUX3: at 2800 mV 
[    3.740783] VAUX4: at 1200 mV 
[    3.755889] VDD1: 600 <--> 1450 mV at 1300 mV 
[    3.774047] VDAC: 1800 mV 
[    3.791046] VIO: at 1800 mV 
[    3.815093] VINTANA1: 1500 mV 
[    3.834625] VINTANA2: at 2750 mV 
[    3.848541] VINTDIG: 1500 mV 
[    3.859039] VMMC1: 1850 <--> 3150 mV at 1850 mV 
[    3.874176] VMMC2: 1850 <--> 3150 mV at 2600 mV 
[    3.886108] VUSB1V5: 1500 mV 
[    3.895141] VUSB1V8: 1800 mV 
[    3.903686] VUSB3V1: 3100 mV 
[    3.921081] VPLL1: at 1300 mV 
[    3.935699] VPLL2: 1800 mV 
[    3.947784] VSIM: 1800 <--> 3000 mV at 1800 mV 
[    3.960906] twl4030_gpio twl4030-gpio: gpio (irq 274) chaining IRQs 290..307
[    3.971343] gpiochip_find_base: found new base at 494
[    3.979125] gpiochip_add: registered GPIOs 494 to 511 on device: twl4030
[    4.005065] mtdoops: mtd device (mtddev=name/number) must be supplied
[    4.030670] smc91x 8000300.ethernet (unregistered net_device): smc91x: IOADDR c887a300 doesn't match configuration (0).
[    4.043395] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico@fluxnic.net>
[    4.058044] smc91x 8000300.ethernet eth0: SMC91C94 (rev 9) at c887a300 IRQ 261
[    4.065887] 
[    4.067504] smc91x 8000300.ethernet eth0: Ethernet addr: 10:03:31:33:16:8f
[    4.080169] usbcore: registered new interface driver asix
[    4.086364] usbcore: registered new interface driver ax88179_178a
[    4.093444] usbcore: registered new interface driver cdc_ether
[    4.100433] usbcore: registered new interface driver smsc95xx
[    4.107025] usbcore: registered new interface driver net1080
[    4.113647] usbcore: registered new interface driver cdc_subset
[    4.120605] usbcore: registered new interface driver zaurus
[    4.127349] usbcore: registered new interface driver cdc_ncm
[    4.138031] usbcore: registered new interface driver cdc_wdm
[    4.144989] usbcore: registered new interface driver usb-storage
[    4.152221] usbcore: registered new interface driver usbtest
[    4.165832] mousedev: PS/2 mouse device common for all mice
[    4.174896] twl4030_keypad keypad.29: OF: linux,keymap property not defined in /ocp/i2c@48072000/twl@48/keypad
[    4.185760] twl4030_keypad keypad.29: Failed to build keymap
[    4.192108] twl4030_keypad: probe of keypad.29 failed with error -2
[    4.210388] input: twl4030_pwrbutton as /devices/ocp.3/48072000.i2c/i2c-1/1-0048/pwrbutton.28/input/input1
[    4.233215] twl_rtc rtc.4: Power up reset detected.
[    4.242218] twl_rtc rtc.4: Enabling TWL-RTC
[    4.275604] twl_rtc rtc.4: rtc core: registered rtc.4 as rtc0
[    4.289245] i2c /dev entries driver
[    4.302185] Driver for 1-wire Dallas network protocol.
[    4.326416] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]'
[    4.335937] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]'
[    4.353424] omap_hsmmc 4809c000.mmc: pins are not configured from the driver
[    4.421447] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]'
[    4.430877] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]'
[    4.441192] 480b4000.mmc supply vmmc not found, using dummy regulator
[    4.448730] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22)
[    4.455932] omap_hsmmc 480b4000.mmc: pins are not configured from the driver
[    4.464935] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22)
[    4.512451] usbcore: registered new interface driver usbhid
[    4.518341] usbhid: USB HID core driver
[    4.526519] oprofile: using arm/armv6
[    4.532440] TCP: cubic registered
[    4.535980] Initializing XFRM netlink socket
[    4.541107] NET: Registered protocol family 17
[    4.546020] NET: Registered protocol family 15
[    4.551910] Key type dns_resolver registered
[    4.557067] Registering SWP/SWPB emulation handler
[    4.582366] VUSB3V1: disabling
[    4.591949] VUSB1V8: disabling
[    4.600555] VUSB1V5: disabling
[    4.631378] twl_rtc rtc.4: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    4.741882] Waiting for root device /dev/mmcblk0p1...