U-Boot SPL 2013.01-rc1-00207-gfbeb8fc-dirty (Nov 29 2012 - 03:05:13) OMAP4460 ES1.1 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2013.01-rc1-00207-gfbeb8fc-dirty (Nov 29 2012 - 03:05:13) CPU : OMAP4460 ES1.1 Board: OMAP4 Panda I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 3  0 Panda # Panda # setenv bootargs 'console=ttyO2,230400n8 root=/dev/mmcblk0p2 rootwait vram=32M earlyprintk ignore_loglevel init=/bin/sh' Panda # loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 230400 bps... CSending: uImage-dtb.omap4-panda-es Sending: Transfer complete CRC mode, 9(SOH)/4245(STX)/0(CAN) packets, 3 retries ## Total Size = 0x0042570b = 4347659 Bytes Panda # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4347595 Bytes = 4.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.15.0-rc7-15519-gc720816 (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed May 28 12:12:29 MDT 2014 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP4 PandaBoard [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at ae800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 261888 [ 0.000000] free_area_init_node: node 0, pgdat c0898700, node_mem_map edff2000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 528 pages used for memmap [ 0.000000] HighMem zone: 67328 pages, LIFO batch:15 [ 0.000000] OMAP4460 ES1.1 [ 0.000000] PERCPU: Embedded 9 pages/cpu @edf98000 s14080 r8192 d14592 u36864 [ 0.000000] pcpu-alloc: s14080 r8192 d14592 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260368 [ 0.000000] Kernel command line: console=ttyO2,230400n8 root=/dev/mmcblk0p2 rootwait vram=32M earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1007396K/1047552K available (5576K kernel code, 663K rwdata, 2148K rodata, 393K init, 5522K bss, 40156K reserved, 269312K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0793384 (7725 kB) [ 0.000000] .init : 0xc0794000 - 0xc07f6700 ( 394 kB) [ 0.000000] .data : 0xc07f8000 - 0xc089df00 ( 664 kB) [ 0.000000] .bss : 0xc089df00 - 0xc0e02a98 (5523 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node bandgap_fclk [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000183] smp_twd: clock not found -2 [ 0.002166] Console: colour dummy device 80x30 [ 0.002258] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.002258] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.002288] ... MAX_LOCK_DEPTH: 48 [ 0.002288] ... MAX_LOCKDEP_KEYS: 8191 [ 0.002288] ... CLASSHASH_SIZE: 4096 [ 0.002288] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.002319] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.002319] ... CHAINHASH_SIZE: 16384 [ 0.002319] memory used by lock dependency info: 3695 kB [ 0.002319] per task-struct memory footprint: 1152 bytes [ 0.002380] Calibrating local timer... 347.62MHz. [ 0.058654] Calibrating delay loop... 1384.44 BogoMIPS (lpj=6922240) [ 0.148010] pid_max: default: 32768 minimum: 301 [ 0.148620] Security Framework initialized [ 0.148834] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.148864] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.151916] CPU: Testing write buffer coherency: ok [ 0.153411] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.153472] Setting up static identity map for 0x80549150 - 0x805491c0 [ 0.153594] L310 cache controller enabled [ 0.153625] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e470000, Cache size: 1024 kB [ 0.158813] CPU1: Booted secondary processor [ 0.197692] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.198303] Brought up 2 CPUs [ 0.198333] SMP: Total of 2 processors activated. [ 0.198333] CPU: All CPU(s) started in SVC mode. [ 0.201080] devtmpfs: initialized [ 0.210174] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.214385] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.218292] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.382781] pinctrl core: initialized pinctrl subsystem [ 0.385375] regulator-dummy: no parameters [ 0.433441] NET: Registered protocol family 16 [ 0.440399] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.512695] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.513519] OMAP GPIO hardware version 0.1 [ 0.514556] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.516235] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.517852] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.519500] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.521057] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.522399] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.540863] platform 4b501000.aes: Cannot lookup hwmod 'aes' [ 0.541290] platform 480a5000.des: Cannot lookup hwmod 'des' [ 0.549499] No ATAGs? [ 0.549591] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.549591] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.552215] OMAP DMA hardware revision 0.0 [ 0.574981] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.575042] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 0.608489] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.609436] of_get_named_gpiod_flags exited with status 0 [ 0.684539] hsusb1_vbus: 3300 mV [ 0.685089] reg-fixed-voltage wl12xx_vmmc.10: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_gpio, deferring probe [ 0.685119] platform wl12xx_vmmc.10: Driver reg-fixed-voltage requests probe deferral [ 0.689666] SCSI subsystem initialized [ 0.690368] usbcore: registered new interface driver usbfs [ 0.690521] usbcore: registered new interface driver hub [ 0.690795] usbcore: registered new device driver usb [ 0.691223] of_get_named_gpiod_flags exited with status 0 [ 0.692474] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 0.692504] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 0.692596] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 0.692596] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 0.692657] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 0.692687] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 0.692749] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 0.692779] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 0.696868] Switched to clocksource 32k_counter [ 0.827697] NET: Registered protocol family 2 [ 0.829528] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.829772] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.832366] TCP: Hash tables configured (established 8192 bind 8192) [ 0.832580] TCP: reno registered [ 0.832611] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.832977] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.834197] NET: Registered protocol family 1 [ 0.835388] RPC: Registered named UNIX socket transport module. [ 0.835418] RPC: Registered udp transport module. [ 0.835418] RPC: Registered tcp transport module. [ 0.835449] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.837158] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.841888] futex hash table entries: 512 (order: 3, 32768 bytes) [ 1.001800] bounce pool size: 64 pages [ 1.002746] VFS: Disk quotas dquot_6.5.2 [ 1.002868] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.004882] NFS: Registering the id_resolver key type [ 1.005218] Key type id_resolver registered [ 1.005249] Key type id_legacy registered [ 1.005340] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.005920] msgmni has been set to 1473 [ 1.008819] io scheduler noop registered [ 1.008819] io scheduler deadline registered [ 1.008911] io scheduler cfq registered (default) [ 1.013793] pinctrl-single 4a100040.pinmux: 203 pins at pa fc100040 size 406 [ 1.014251] pinctrl-single 4a31e040.pinmux: 28 pins at pa fc31e040 size 56 [ 1.016601] pbias_mmc_omap4: 1800 <--> 3000 mV at 3000 mV [ 1.017944] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.024139] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.024169] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]' [ 1.025024] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 104, base_baud = 3000000) is a OMAP UART0 [ 1.026855] omap_uart 4806c000.serial: no wakeirq for uart0 [ 1.026885] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]' [ 1.027343] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 105, base_baud = 3000000) is a OMAP UART1 [ 1.028503] omap_uart 48020000.serial: no wakeirq for uart0 [ 1.028533] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@48020000[0]' [ 1.028961] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 106, base_baud = 3000000) is a OMAP UART2 [ 1.524688] console [ttyO2] enabled [ 1.527740] omap_uart 4806e000.serial: no wakeirq for uart0 [ 1.530792] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806e000[0]' [ 1.536224] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 102, base_baud = 3000000) is a OMAP UART3 [ 1.561920] brd: module loaded [ 1.575653] loop: module loaded [ 1.580200] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.590362] usbcore: registered new interface driver asix [ 1.593444] usbcore: registered new interface driver ax88179_178a [ 1.596954] usbcore: registered new interface driver cdc_ether [ 1.600311] usbcore: registered new interface driver smsc95xx [ 1.603576] usbcore: registered new interface driver net1080 [ 1.606842] usbcore: registered new interface driver cdc_subset [ 1.610168] usbcore: registered new interface driver zaurus [ 1.613403] usbcore: registered new interface driver cdc_ncm [ 1.617492] usbcore: registered new interface driver cdc_wdm [ 1.620727] usbcore: registered new interface driver usb-storage [ 1.624176] usbcore: registered new interface driver usbtest [ 1.629211] mousedev: PS/2 mouse device common for all mice [ 1.634796] i2c /dev entries driver [ 1.636810] Driver for 1-wire Dallas network protocol. [ 1.640533] of_get_named_gpiod_flags exited with status 0 [ 1.646881] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.652130] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.656921] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.662353] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 1.666198] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.670288] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 1.675048] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 1.680145] omap_hsmmc 480d5000.mmc: unable to get vmmc regulator -517 [ 1.683898] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.688537] usbcore: registered new interface driver usbhid [ 1.691589] usbhid: USB HID core driver [ 1.694793] oprofile: using arm/armv7-ca9 [ 1.697540] TCP: cubic registered [ 1.699340] Initializing XFRM netlink socket [ 1.701782] NET: Registered protocol family 17 [ 1.704254] NET: Registered protocol family 15 [ 1.707031] Key type dns_resolver registered [ 1.710479] Power Management for TI OMAP4+ devices. [ 1.713195] Power Management for TI OMAP4. [ 1.715454] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.719299] ThumbEE CPU extension supported. [ 1.719299] Registering SWP/SWPB emulation handler [ 1.726837] pbias_mmc_omap4: disabling [ 1.729675] of_get_named_gpiod_flags exited with status 0 [ 1.729675] vwl1271: 1800 mV [ 1.741302] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.749725] twl 0-0048: PIH (irq 39) nested IRQs [ 1.754272] twl_rtc rtc.15: Power up reset detected. [ 1.758026] twl_rtc rtc.15: Enabling TWL-RTC [ 1.765167] twl_rtc rtc.15: rtc core: registered rtc.15 as rtc0 [ 1.770324] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.775299] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.780059] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.784820] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.789428] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.793731] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.797943] VDAC: 1800 mV [ 1.800689] VANA: 2100 mV [ 1.803894] VCXIO: 1800 mV [ 1.806701] VUSB: 3300 mV [ 1.809875] V1V8: 1800 mV [ 1.813018] V2V1: 2100 mV [ 1.820922] of_get_named_gpiod_flags exited with status 0 [ 1.826599] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 1.831634] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 1.837677] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 1.842224] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 1.845367] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.850555] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 1.859436] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 1.897674] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 1.902526] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 2.029602] twl_rtc rtc.15: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.072326] Waiting for root device /dev/mmcblk0p2... [ 2.255828] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.263031] mmc0: new high speed SD card at address 1234 [ 2.267822] mmcblk0: mmc0:1234 SA02G 1.83 GiB [ 2.275878] mmcblk0: p1 p2 [ 2.285522] omap_hsmmc 480d5000.mmc: card claims to support voltages below defined range [ 2.301483] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.306457] mmc1: new SDIO card at address 0001 [ 2.312927] kjournald starting. Commit interval 5 seconds [ 2.312927] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.312927] VFS: Mounted root (ext3 filesystem) readonly on device 179:2. [ 2.325561] devtmpfs: mounted [ 2.327239] Freeing unused kernel memory: 392K (c0794000 - c07f6000) /bin/sh: can't access tty; job control turned off / # / # / # / # / # %% Start PM consolidated quick test (retention only) %% Preparation / # / # mount -t sysfs none /sys / # / # mount -t debugfs none /debug / # / # / # / # for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d'  '`; do echo -1 > $u/power/autosuspend_delay_ms; done / # / # echo 0 > /debug/pm_debug/enable_off_mode / # / # %% Baseline pm_debug count dump cat /debug/pm_debug/count [ 9.454223] pwrdm state mismatch(ivahd_pwrdm) 3 != 1 [ 9.457061] pwrdm state mismatch(tesla_pwrdm) 3 != 1 [ 9.459838] pwrdm state mismatch(dss_pwrdm) 3 != 1 cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:3,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (ON),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:0 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (7) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # echo enabled > /sys/devices/44000000.ocp/48020000.serial/tty/ttyO2/power/wak eup / # %% Start retention double suspend/resume UART wakeup test echo mem > /sys/power/state [ 11.652587] PM: Syncing filesystems ... done. [ 11.652587] PM: Preparing system for mem sleep [ 11.663055] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 11.669097] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done. [ 11.674438] PM: Entering mem sleep [ 11.677856] Suspending console(s) (use no_console_suspend to debug) [ 11.696197] PM: suspend of devices complete after 18.341 msecs [ 11.700805] PM: late suspend of devices complete after 0.671 msecs [ 11.706420] PM: noirq suspend of devices complete after 5.615 msecs [ 11.706420] Disabling non-boot CPUs ... [ 11.712432] CPU1: shutdown [ 11.713470] Successfully put all powerdomains to target state [ 11.713470] hw-breakpoint: Failed to enable monitor mode on CPU 0. [ 11.713653] Enabling non-boot CPUs ... [ 11.715820] CPU1: Booted secondary processor [ 11.717346] CPU1 is up [ 11.720397] PM: noirq resume of devices complete after 2.929 msecs [ 11.721496] PM: early resume of devices complete after 0.518 msecs [ 12.334167] PM: resume of devices complete after 609.710 msecs [ 12.367614] PM: Finishing wakeup. [ 12.376129] Restarting tasks ... done. / # / # / # / # cat /debug/pm_debug/count cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:6,INA:0,ON:6,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:1,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:1,RET:0,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:1,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:1 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (12) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # / # / # echo mem > /sys/power/state [ 14.917297] PM: Syncing filesystems ... done. [ 14.920379] PM: Preparing system for mem sleep [ 14.923400] Freezing user space processes ... (elapsed 0.003 seconds) done. [ 14.926666] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 14.933715] PM: Entering mem sleep [ 14.933715] Suspending console(s) (use no_console_suspend to debug) [ 14.950988] PM: suspend of devices complete after 9.185 msecs [ 14.955474] PM: late suspend of devices complete after 4.486 msecs [ 14.960510] PM: noirq suspend of devices complete after 5.035 msecs [ 14.960510] Disabling non-boot CPUs ... [ 14.962493] CPU1: shutdown [ 14.964599] Successfully put all powerdomains to target state [ 14.964599] hw-breakpoint: CPU 0 failed to disable vector catch [ 14.964630] Enabling non-boot CPUs ... [ 14.966552] CPU1: Booted secondary processor [ 14.967315] CPU1 is up [ 14.970275] PM: noirq resume of devices complete after 2.868 msecs [ 14.974090] PM: early resume of devices complete after 1.129 msecs [ 15.554809] PM: resume of devices complete after 580.718 msecs [ 15.590972] PM: Finishing wakeup. [ 15.590972] Restarting tasks ... done. / # / # / # / # cat /debug/pm_debug/count cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:9,INA:0,ON:9,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:2,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:2 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (12) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # / # / # ./test_rootfs_access_nonexistent_file__ret_susp /bin/sh: ./test_rootfs_access_nonexistent_file__ret_susp: not found / # / # %% End retention double suspend/resume UART wakeup test %% Start retention dynamic idle UART wakeup test for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d'  '`; do echo 3000 > $u/power/autosuspend_delay_ms; done / # / # / # / # cat /debug/pm_debug/count cefuse_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0 always_on_core_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0 l4per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 l3init_pwrdm (RET),OFF:0,RET:9,INA:0,ON:9,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0 cam_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 ivahd_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 mpu_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:2,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 cpu1_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cpu0_pwrdm (ON),OFF:2,RET:0,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 tesla_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0 dss_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 abe_pwrdm (RET),OFF:1,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 gfx_pwrdm (OFF),OFF:2,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:2,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0,RET-MEMBANK5-OFF:2 l3_dma_clkdm->core_pwrdm (0) emu_sys_clkdm->emu_pwrdm (0) l4_wkup_clkdm->wkup_pwrdm (3) l3_dss_clkdm->dss_pwrdm (0) iss_clkdm->cam_pwrdm (0) l3_1_clkdm->core_pwrdm (0) l3_2_clkdm->core_pwrdm (1) mpuss_clkdm->mpu_pwrdm (1) ducati_clkdm->core_pwrdm (0) l4_ao_clkdm->always_on_core_pwrdm (0) l3_emif_clkdm->core_pwrdm (2) mpu1_clkdm->cpu1_pwrdm (0) mpu0_clkdm->cpu0_pwrdm (0) d2d_clkdm->core_pwrdm (0) l3_init_clkdm->l3init_pwrdm (0) l3_instr_clkdm->core_pwrdm (0) abe_clkdm->abe_pwrdm (0) l4_per_clkdm->l4per_pwrdm (4) l4_secure_clkdm->l4per_pwrdm (0) ivahd_clkdm->ivahd_pwrdm (0) l3_gfx_clkdm->gfx_pwrdm (0) tesla_clkdm->tesla_pwrdm (0) l4_cfg_clkdm->core_pwrdm (0) l4_cefuse_clkdm->cefuse_pwrdm (0) / # / # / # / # ./test_rootfs_access_nonexistent_file__ret_dyn /bin/sh: ./test_rootfs_access_nonexistent_file__ret_dyn: not found / # / # for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d'  '`; do echo -1 > $u/power/autosuspend_delay_ms; done / # / # %% End retention dynamic idle UART wakeup test %% End PM consolidated quick test (retention only)