Texas Instruments X-Loader 1.47 (Jan 14 2011 - 15:43:28) Starting X-loader on MMC Reading boot sector 212836 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... U-Boot 2010.06 (Jan 14 2011 - 15:43:45) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 EVM board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB In: serial Out: serial Err: serial Read back SMSC id 0x92200000 Die ID #368000229ff80000016071640902c013 Net: smc911x-0 Hit any key to stop autoboot: 3  2  1  0 OMAP3_EVM # OMAP3_EVM # setenv bootfile uImage-dtb.omap3-evm-37xx OMAP3_EVM # OMAP3_EVM # dhcp smc911x: detected LAN9220 controller smc911x: phy initialized smc911x: MAC 00:50:c2:7e:99:42 BOOTP broadcast 1 DHCP client bound to address 192.168.57.131 Using smc911x-0 device TFTP from server 192.168.57.1; our IP address is 192.168.57.131 Filename 'uImage-dtb.omap3-evm-37xx'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###### done Bytes transferred = 4353943 (426f97 hex) OMAP3_EVM # setenv bootargs console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh OMAP3_EVM # OMAP3_EVM # bootm ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4353879 Bytes = 4.2 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.15.0-66267-g1860e37 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Sun Jun 8 18:50:24 MDT 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP37XX EVM (TMDSEVM3730) [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at 8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c0898780, node_mem_map cfcf2000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @cfca8000 s14080 r8192 d14592 u36864 [ 0.000000] pcpu-alloc: s14080 r8192 d14592 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 227748K/261120K available (5580K kernel code, 663K rwdata, 2148K rodata, 393K init, 5522K bss, 33372K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0794394 (7729 kB) [ 0.000000] .init : 0xc0795000 - 0xc07f7700 ( 394 kB) [ 0.000000] .data : 0xc07f8000 - 0xc089df80 ( 664 kB) [ 0.000000] .bss : 0xc089df80 - 0xc0e02b18 (5523 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001129] Console: colour dummy device 80x30 [ 0.001190] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001220] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001220] ... MAX_LOCK_DEPTH: 48 [ 0.001220] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001251] ... CLASSHASH_SIZE: 4096 [ 0.001251] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.001281] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.001281] ... CHAINHASH_SIZE: 16384 [ 0.001281] memory used by lock dependency info: 3695 kB [ 0.001312] per task-struct memory footprint: 1152 bytes [ 0.001373] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696) [ 0.107635] pid_max: default: 32768 minimum: 301 [ 0.108245] Security Framework initialized [ 0.108428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.108459] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.111877] CPU: Testing write buffer coherency: ok [ 0.113464] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.113555] Setting up static identity map for 0x805498d0 - 0x80549940 [ 0.118041] Brought up 1 CPUs [ 0.118072] SMP: Total of 1 processors activated. [ 0.118072] CPU: All CPU(s) started in SVC mode. [ 0.121917] devtmpfs: initialized [ 0.132537] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.211059] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.213287] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.320098] pinctrl core: initialized pinctrl subsystem [ 0.323760] regulator-dummy: no parameters [ 0.414276] NET: Registered protocol family 16 [ 0.426696] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.441009] Reprogramming SDRC clock to 400000000 Hz [ 0.453430] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.454711] OMAP GPIO hardware version 2.5 [ 0.456451] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.459259] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.461914] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.464538] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.467254] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.492614] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 0.494079] gpmc_probe_nand_child: ti,elm-id property not found [ 0.494293] gpmc_cs_program_settings: invalid width 0! [ 0.499877] No ATAGs?[ 0.499908] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.503845] OMAP DMA hardware revision 5.0 [ 0.538116] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.538208] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 0.591430] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.592590] of_get_named_gpiod_flags: can't parse gpios property of node '/regulator-vddvario[0]' [ 0.593444] vddvario: no parameters [ 0.594055] of_get_named_gpiod_flags: can't parse gpios property of node '/regulator-vdd33a[0]' [ 0.594604] vdd33a: no parameters [ 0.595245] reg-fixed-voltage wl12xx_vmmc.6: could not find pctldev for node /ocp/pinmux@48002030/pinmux_wl12xx_gpio, deferring probe [ 0.595306] platform wl12xx_vmmc.6: Driver reg-fixed-voltage requests probe deferral [ 0.600921] SCSI subsystem initialized [ 0.602081] usbcore: registered new interface driver usbfs [ 0.602325] usbcore: registered new interface driver hub [ 0.602905] usbcore: registered new device driver usb [ 0.750579] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz [ 0.752380] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz [ 0.756011] omap_i2c 48060000.i2c: bus 2 rev4.4 at 400 kHz [ 0.763244] Switched to clocksource 32k_counter [ 0.974151] NET: Registered protocol family 2 [ 0.976562] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.976806] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.977935] TCP: Hash tables configured (established 2048 bind 2048) [ 0.978149] TCP: reno registered [ 0.978179] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.978485] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.980072] NET: Registered protocol family 1 [ 0.982543] RPC: Registered named UNIX socket transport module. [ 0.982574] RPC: Registered udp transport module. [ 0.982696] RPC: Registered tcp transport module. [ 0.982727] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.984405] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.992004] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.205535] VFS: Disk quotas dquot_6.5.2 [ 1.205749] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.208953] NFS: Registering the id_resolver key type [ 1.209503] Key type id_resolver registered [ 1.209533] Key type id_legacy registered [ 1.209716] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.210388] msgmni has been set to 476 [ 1.218231] io scheduler noop registered [ 1.218261] io scheduler deadline registered [ 1.218383] io scheduler cfq registered (default) [ 1.221649] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568 [ 1.222412] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92 [ 1.223663] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size 92 [ 1.226806] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV [ 1.228637] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.238464] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.238494] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]' [ 1.240295] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 2.083679] console [ttyO0] enabled [ 2.089660] omap_uart 4806c000.serial: no wakeirq for uart0 [ 2.095642] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]' [ 2.109588] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 2.123626] omap_uart 49020000.serial: no wakeirq for uart0 [ 2.129547] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@49020000[0]' [ 2.140258] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 2.155029] omap_uart 49042000.serial: no wakeirq for uart0 [ 2.160919] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@49042000[0]' [ 2.175781] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3 [ 2.222900] brd: module loaded [ 2.249237] loop: module loaded [ 2.270172] twl 0-0048: PIH (irq 23) chaining IRQs 338..346 [ 2.276733] twl 0-0048: power (irq 343) chaining IRQs 346..353 [ 2.291473] VAUX1: at 3000 mV [ 2.299591] VAUX2_4030: at 1800 mV [ 2.307708] VAUX3: at 2800 mV [ 2.315216] VAUX4: at 2800 mV [ 2.322814] VDD1: 600 <--> 1450 mV at 1200 mV [ 2.332336] VDAC: 1800 mV [ 2.346282] VIO: at 1800 mV [ 2.354553] VINTANA1: 1500 mV [ 2.362457] VINTANA2: at 2750 mV [ 2.371215] VINTDIG: 1500 mV [ 2.377227] VMMC1: 1850 <--> 3150 mV at 3000 mV [ 2.387115] VMMC2: 1850 <--> 3150 mV at 2600 mV [ 2.395965] VUSB1V5: 1500 mV [ 2.401031] VUSB1V8: 1800 mV [ 2.406707] VUSB3V1: 3100 mV [ 2.414428] VPLL1: at 1800 mV [ 2.421997] VPLL2: 1800 mV [ 2.428955] VSIM: 1800 <--> 3000 mV at 1800 mV [ 2.437652] twl4030_gpio twl4030-gpio: gpio (irq 338) chaining IRQs 354..371 [ 2.446197] gpiochip_find_base: found new base at 492 [ 2.452545] gpiochip_add: registered GPIOs 492 to 511 on device: twl4030 [ 2.467712] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.523956] libphy: smsc911x-mdio: probed [ 2.603424] smsc911x 2c000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=2c000000.etherne:01, irq=-1) [ 2.615783] smsc911x 2c000000.ethernet eth0: MAC Address: 00:50:c2:7e:99:42 [ 2.625061] usbcore: registered new interface driver asix [ 2.630920] usbcore: registered new interface driver ax88179_178a [ 2.637603] usbcore: registered new interface driver cdc_ether [ 2.644042] usbcore: registered new interface driver smsc95xx [ 2.650268] usbcore: registered new interface driver net1080 [ 2.656433] usbcore: registered new interface driver cdc_subset [ 2.662902] usbcore: registered new interface driver zaurus [ 2.669036] usbcore: registered new interface driver cdc_ncm [ 2.676696] usbcore: registered new interface driver cdc_wdm [ 2.683013] usbcore: registered new interface driver usb-storage [ 2.689575] usbcore: registered new interface driver usbtest [ 2.698760] mousedev: PS/2 mouse device common for all mice [ 2.706115] twl4030_keypad keypad.32: OF: linux,keymap property not defined in /ocp/i2c@48070000/twl@48/keypad [ 2.716766] twl4030_keypad keypad.32: Failed to build keymap [ 2.722869] twl4030_keypad: probe of keypad.32 failed with error -2 [ 2.733825] input: twl4030_pwrbutton as /devices/68000000.ocp/48070000.i2c/i2c-0/0-0048/pwrbutton.31/input/input1 [ 2.748535] twl_rtc rtc.7: Power up reset detected. [ 2.753967] twl_rtc rtc.7: Enabling TWL-RTC [ 2.765350] twl_rtc rtc.7: rtc core: registered rtc.7 as rtc0 [ 2.774353] i2c /dev entries driver [ 2.782257] Driver for 1-wire Dallas network protocol. [ 2.792266] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.806213] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.815612] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.873321] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 2.882476] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 2.892395] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 [ 2.899993] platform 480b4000.mmc: Driver omap_hsmmc requests probe deferral [ 2.908813] usbcore: registered new interface driver usbhid [ 2.914764] usbhid: USB HID core driver [ 2.920684] oprofile: using arm/armv7 [ 2.925323] TCP: cubic registered [ 2.928833] Initializing XFRM netlink socket [ 2.933563] NET: Registered protocol family 17 [ 2.938354] NET: Registered protocol family 15 [ 2.943511] Key type dns_resolver registered [ 2.950134] ThumbEE CPU extension supported. [ 2.954803] Registering SWP/SWPB emulation handler [ 2.978363] VUSB3V1: disabling [ 2.985687] of_get_named_gpiod_flags exited with status 0 [ 2.993041] vwl1271: 1800 mV [ 2.996429] vwl1271: supplied by VMMC2 [ 3.002014] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 3.011383] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480b4000[0]' [ 3.137268] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.150512] mmc0: new SDHC card at address e624 [ 3.158508] twl_rtc rtc.7: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.344360] smsc911x 2c000000.ethernet eth0: SMSC911x/921x identified at 0xd087c000, IRQ: 288 [ 3.355255] mmcblk0: mmc0:e624 SD08G 7.40 GiB [ 3.373199] Sending DHCP requests . [ 3.377929] mmcblk0: p1 p2 p3 [ 5.922882] ., OK [ 5.943420] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.131 [ 5.952117] IP-Config: Complete: [ 5.955627] device=eth0, hwaddr=00:50:c2:7e:99:42, ipaddr=192.168.57.131, mask=255.255.255.0, gw=255.255.255.255 [ 5.966888] host=192.168.57.131, domain=example.org, nis-domain=(none) [ 5.974273] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.981048] nameserver0=192.168.57.1 [ 6.010772] VFS: Mounted root (nfs filesystem) readonly on device 0:13. [ 6.020111] devtmpfs: mounted [ 6.024414] Freeing unused kernel memory: 392K (c0795000 - c07f7000) /bin/sh: 0: can't access tty; job control turned off # %% Start PM consolidated quick test %% Preparation # # mount -t sysfs none /sys # # mount -t debugfs none /debug # # # # for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d' '`; do echo -1 > $u/power/autosuspend_delay_ms; done # # echo 0 > /debug/pm_debug/enable_off_mode # # %% Baseline pm_debug count dump cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:432,INA:0,ON:433,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:432,INA:0,ON:433,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:432,INA:0,ON:433,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:432,INA:0,ON:433,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (1) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (15) cam_clkdm->cam_pwrdm (0) dss_clkdm->dss_pwrdm (1) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (22) core_l3_clkdm->core_pwrdm (1) neon_clkdm->neon_pwrdm (0) # # echo enabled > /sys/devices/44000000.ocp/48020000.serial/tty/ttyO2/power/wakeup /bin/sh: 15: cannot create /sys/devices/44000000.ocp/48020000.serial/tty/ttyO2/power/wakeup: Directory nonexistent # %% Start retention double suspend/resume UART wakeup test echo mem > /sys/power/state [ 13.549377] PM: Syncing filesystems ... done. [ 13.556701] PM: Preparing system for mem sleep [ 13.569519] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 13.577209] Freezing remaining freezable tasks ... (elapsed 0.003 seconds) done. [ 13.588439] PM: Entering mem sleep [ 13.592010] Suspending console(s) (use no_console_suspend to debug) [ 13.622375] PM: suspend of devices complete after 18.676 msecs [ 13.630065] PM: late suspend of devices complete after 7.629 msecs [ 13.638580] PM: noirq suspend of devices complete after 8.514 msecs [ 13.638671] Disabling non-boot CPUs ... [ 13.638793] Successfully put all powerdomains to target state [ 13.643676] PM: noirq resume of devices complete after 4.791 msecs [ 13.649871] PM: early resume of devices complete after 5.035 msecs [ 13.835083] PM: resume of devices complete after 185.119 msecs [ 13.890136] PM: Finishing wakeup. [ 13.893676] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:545,INA:0,ON:546,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:545,INA:0,ON:546,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:545,INA:0,ON:546,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:545,INA:0,ON:546,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (1) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (15) cam_clkdm->cam_pwrdm (0) dss_clkdm->dss_pwrdm (1) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (26) core_l3_clkdm->core_pwrdm (1) neon_clkdm->neon_pwrdm (0) # # # # echo mem > /sys/power/state [ 15.842346] PM: Syncing filesystems ... done. [ 15.847381] PM: Preparing system for mem sleep [ 15.854187] Freezing user space processes ... (elapsed 0.000 seconds) done. [ 15.861724] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 15.871612] PM: Entering mem sleep [ 15.875244] Suspending console(s) (use no_console_suspend to debug) [ 15.900146] PM: suspend of devices complete after 13.549 msecs [ 15.907745] PM: late suspend of devices complete after 7.568 msecs [ 15.915863] PM: noirq suspend of devices complete after 8.087 msecs [ 15.915893] Disabling non-boot CPUs ... [ 15.915985] Successfully put all powerdomains to target state [ 15.920654] PM: noirq resume of devices complete after 4.638 msecs [ 15.926910] PM: early resume of devices complete after 5.157 msecs [ 16.114898] PM: resume of devices complete after 187.896 msecs [ 16.169433] PM: Finishing wakeup. [ 16.172973] Restarting tasks ... done. # # # # cat /debug/pm_debug/count usbhost_pwrdm (ON),OFF:0,RET:654,INA:0,ON:655,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0 per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 dss_pwrdm (ON),OFF:0,RET:654,INA:0,ON:655,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 neon_pwrdm (ON),OFF:0,RET:654,INA:0,ON:655,RET-LOGIC-OFF:0 mpu_pwrdm (ON),OFF:0,RET:654,INA:0,ON:655,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0 iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0 usbhost_clkdm->usbhost_pwrdm (1) sgx_clkdm->sgx_pwrdm (0) per_clkdm->per_pwrdm (15) cam_clkdm->cam_pwrdm (0) dss_clkdm->dss_pwrdm (1) d2d_clkdm->core_pwrdm (0) iva2_clkdm->iva2_pwrdm (0) mpu_clkdm->mpu_pwrdm (0) core_l4_clkdm->core_pwrdm (22) core_l3_clkdm->core_pwrdm (1) neon_clkdm->neon_pwrdm (0) # # # # ./test_rootfs_access_nonexistent_file__ret_susp /bin/sh: 32: ./test_rootfs_access_nonexistent_file__ret_susp: not found # # %% End retention double suspend/resume UART wakeup test %% Start retention dynamic idle UART wakeup test for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.serial | paste -s -d' '`; do echo 3000 > $u/power/autosuspend_delay_ms; done # #