U-Boot SPL 2012.07-00012-g391a28d (Dec 30 2012 - 17:40:39) OMAP4460 ES1.1 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.bin mkimage signature not found - ih_magic = ea000014 reading u-boot.bin U-Boot 2012.07-00012-g391a28d (Dec 30 2012 - 17:40:39) CPU : OMAP4460 ES1.1 Board: OMAP4 Variscite SOM I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Using default environment In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. checking for preEnv.txt reading preEnv.txt 0 bytes read Loaded environment from preEnv.txt Importing preboot environment from mmc ... Hit any key to stop autoboot: 3  0 VAR-SOM-OM44 # VAR-SOM-OM44 # setenv bootargs 'console=ttyO2,115200n8 mem=1G@0x80000000 root=/dev/mmcblk0p2 ro earlyprintk ignore_loglevel fixrtc phy.smsc.gb_enable=false video=HDMI-A-1:1920x1080@60' VAR-SOM-OM44 # loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 115200 bps... CSending: uImage-dtb.omap4-var-som Sending: Transfer complete - CRC mode, 4(SOH)/4305(STX)/0(CAN) packets, 3 retries ## Total Size = 0x004344a1 = 4408481 Bytes VAR-SOM-OM44 # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4408417 Bytes = 4.2 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.16.0-rc3-79057-g4c83445 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Mon Jun 30 00:49:39 MDT 2014 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Variscite OMAP4 SOM [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at ae800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 261888 [ 0.000000] free_area_init_node: node 0, pgdat c08be9c0, node_mem_map edff1000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 526 pages used for memmap [ 0.000000] HighMem zone: 67328 pages, LIFO batch:15 [ 0.000000] OMAP4460 ES1.1 [ 0.000000] L2C: platform modifies aux control register: 0x0e070000 -> 0x3e470000 [ 0.000000] L2C: DT/platform modifies aux control register: 0x0e070000 -> 0x3e470000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm/mach-omap2/omap4-common.c:192 omap4_l2c310_write_sec+0x5c/0x98() [ 0.000000] OMAP L2C310: ignoring write to reg 0xf80 [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 3.16.0-rc3-79057-g4c83445 #1 [ 0.000000] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 0.000000] [] (show_stack) from [] (dump_stack+0x80/0x9c) [ 0.000000] [] (dump_stack) from [] (warn_slowpath_common+0x68/0x8c) [ 0.000000] [] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40) [ 0.000000] [] (warn_slowpath_fmt) from [] (omap4_l2c310_write_sec+0x5c/0x98) [ 0.000000] [] (omap4_l2c310_write_sec) from [] (l2c310_enable+0x13c/0x200) [ 0.000000] [] (l2c310_enable) from [] (__l2c_init+0x168/0x1f0) [ 0.000000] [] (__l2c_init) from [] (l2x0_of_init+0x178/0x1ac) [ 0.000000] [] (l2x0_of_init) from [] (omap_l2_cache_init+0x44/0x9c) [ 0.000000] [] (omap_l2_cache_init) from [] (omap4430_init_early+0x6c/0xa0) [ 0.000000] [] (omap4430_init_early) from [] (setup_arch+0x8b4/0x998) [ 0.000000] [] (setup_arch) from [] (start_kernel+0x7c/0x3a0) [ 0.000000] [] (start_kernel) from [<80008074>] (0x80008074) [ 0.000000] ---[ end trace 3406ff24bd97382e ]--- [ 0.000000] L2C-310 dynamic clock gating disabled, standby mode disabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x7e470000 [ 0.000000] PERCPU: Embedded 9 pages/cpu @edf9e000 s14336 r8192 d14336 u36864 [ 0.000000] pcpu-alloc: s14336 r8192 d14336 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260368 [ 0.000000] Kernel command line: console=ttyO2,115200n8 mem=1G@0x80000000 root=/dev/mmcblk0p2 ro earlyprintk ignore_loglevel fixrtc phy.smsc.gb_enable=false video=HDMI-A-1:1920x1080@60 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1004584K/1047552K available (5655K kernel code, 680K rwdata, 2196K rodata, 406K init, 8209K bss, 42968K reserved, 269312K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07b2f5c (7852 kB) [ 0.000000] .init : 0xc07b3000 - 0xc0818800 ( 406 kB) [ 0.000000] .data : 0xc081a000 - 0xc08c4330 ( 681 kB) [ 0.000000] .bss : 0xc08c4330 - 0xc10c8820 (8210 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node div_ts_ck [ 0.000000] ti_dt_clocks_register: failed to lookup clock node bandgap_ts_fclk [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000152] smp_twd: clock not found -2 [ 0.001708] Console: colour dummy device 80x30 [ 0.001739] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001739] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001770] ... MAX_LOCK_DEPTH: 48 [ 0.001770] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001800] ... CLASSHASH_SIZE: 4096 [ 0.001800] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001831] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001831] ... CHAINHASH_SIZE: 32768 [ 0.001831] memory used by lock dependency info: 5167 kB [ 0.001861] per task-struct memory footprint: 1152 bytes [ 0.001892] Calibrating local timer... 347.70MHz. [ 0.059020] Calibrating delay loop... 1384.44 BogoMIPS (lpj=6922240) [ 0.148437] pid_max: default: 32768 minimum: 301 [ 0.148895] Security Framework initialized [ 0.149047] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.149078] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.151367] CPU: Testing write buffer coherency: ok [ 0.152435] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152526] Setting up static identity map for 0x8055ba00 - 0x8055ba70 [ 0.158081] CPU1: Booted secondary processor [ 0.188140] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.188720] Brought up 2 CPUs [ 0.188751] SMP: Total of 2 processors activated. [ 0.188751] CPU: All CPU(s) started in SVC mode. [ 0.191406] devtmpfs: initialized [ 0.200836] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.204895] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.208679] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.368194] pinctrl core: initialized pinctrl subsystem [ 0.370727] regulator-dummy: no parameters [ 0.413452] NET: Registered protocol family 16 [ 0.419464] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.421539] cpuidle: using governor ladder [ 0.421600] cpuidle: using governor menu [ 0.434997] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.435852] OMAP GPIO hardware version 0.1 [ 0.437011] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.438720] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.440338] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.441925] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.443542] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.444854] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.462738] platform 4b501000.aes: Cannot lookup hwmod 'aes' [ 0.463256] platform 480a5000.des: Cannot lookup hwmod 'des' [ 0.465270] No ATAGs? [ 0.465362] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.465423] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.467895] OMAP DMA hardware revision 0.0 [ 0.522094] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.522155] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 0.556274] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.557098] of_get_named_gpiod_flags: can't parse gpios property of node '/fixedregulator@0[0]' [ 0.557739] VDD_ETH: 3300 mV [ 0.562103] SCSI subsystem initialized [ 0.562896] usbcore: registered new interface driver usbfs [ 0.563049] usbcore: registered new interface driver hub [ 0.564270] usbcore: registered new device driver usb [ 0.577453] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 0.578552] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 0.580261] omap_i2c 48060000.i2c: bus 2 rev0.11 at 400 kHz [ 0.581146] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 0.585418] Switched to clocksource 32k_counter [ 0.718902] NET: Registered protocol family 2 [ 0.720703] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.720947] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.723571] TCP: Hash tables configured (established 8192 bind 8192) [ 0.723785] TCP: reno registered [ 0.723876] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.724212] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.725585] NET: Registered protocol family 1 [ 0.726715] RPC: Registered named UNIX socket transport module. [ 0.726745] RPC: Registered udp transport module. [ 0.726776] RPC: Registered tcp transport module. [ 0.726776] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.732940] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.737670] VFS: Disk quotas dquot_6.5.2 [ 0.737792] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.739868] NFS: Registering the id_resolver key type [ 0.740203] Key type id_resolver registered [ 0.740234] Key type id_legacy registered [ 0.740386] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.740966] msgmni has been set to 1468 [ 0.743591] bounce: pool size: 64 pages [ 0.743713] io scheduler noop registered [ 0.743743] io scheduler deadline registered [ 0.743835] io scheduler cfq registered (default) [ 0.746673] omap-usb2 4a0ad080.usb2phy: unable to get wkupclk, trying old name [ 0.746734] omap-usb2 4a0ad080.usb2phy: found usb_phy_cm_clk32k, please fix DTS [ 0.748596] pinctrl-single 4a100040.pinmux: 203 pins at pa fc100040 size 406 [ 0.749053] pinctrl-single 4a31e040.pinmux: 28 pins at pa fc31e040 size 56 [ 0.751434] pbias_mmc_omap4: 1800 <--> 3000 mV at 3000 mV [ 0.752838] abb_mpu: 1025 <--> 1389 mV [ 0.753692] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.759094] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.759124] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806a000[0]' [ 0.759552] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 104, base_baud = 3000000) is a OMAP UART0 [ 0.761199] omap_uart 4806c000.serial: no wakeirq for uart0 [ 0.761230] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806c000[0]' [ 0.761444] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 105, base_baud = 3000000) is a OMAP UART1 [ 0.762481] omap_uart 48020000.serial: no wakeirq for uart0 [ 0.762512] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@48020000[0]' [ 0.762725] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 106, base_baud = 3000000) is a OMAP UART2 [ 1.834381] console [ttyO2] enabled [ 1.839202] omap_uart 4806e000.serial: no wakeirq for uart0 [ 1.845062] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@4806e000[0]' [ 1.854675] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 102, base_baud = 3000000) is a OMAP UART3 [ 1.886596] brd: module loaded [ 1.902221] loop: module loaded [ 1.907318] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.917602] twl 0-0048: PIH (irq 39) nested IRQs [ 1.924804] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.932006] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.939117] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.946228] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.952728] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.959197] VUSIM: 1200 <--> 2900 mV [ 1.964416] VDAC: 1800 mV [ 1.968475] VANA: 2100 mV [ 1.973022] VCXIO: 1800 mV [ 1.977172] VUSB: 3300 mV [ 1.981536] V1V8: 1800 mV [ 1.986022] V2V1: 2100 mV [ 1.993988] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.008056] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/spi@48098000/eth@0[0]' [ 2.017761] spi1.0 supply vdd-io not found, using dummy regulator [ 2.024902] ks8851 spi1.0: message enable is 0 [ 2.035400] ks8851 spi1.0 eth0: revision 1, MAC fa:27:8e:e9:d5:7d, IRQ 331, no EEPROM [ 2.046081] usbcore: registered new interface driver asix [ 2.051879] usbcore: registered new interface driver ax88179_178a [ 2.058410] usbcore: registered new interface driver cdc_ether [ 2.064697] usbcore: registered new interface driver smsc95xx [ 2.070861] usbcore: registered new interface driver net1080 [ 2.076934] usbcore: registered new interface driver cdc_subset [ 2.083251] usbcore: registered new interface driver zaurus [ 2.089294] usbcore: registered new interface driver cdc_ncm [ 2.096252] usbcore: registered new interface driver cdc_wdm [ 2.102325] usbcore: registered new interface driver usb-storage [ 2.108856] usbcore: registered new interface driver usbtest [ 2.116882] mousedev: PS/2 mouse device common for all mice [ 2.125823] twl_rtc 48070000.i2c:twl@48:rtc: Power up reset detected. [ 2.133483] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC [ 2.143615] twl_rtc 48070000.i2c:twl@48:rtc: rtc core: registered 48070000.i2c:twl@48 as rtc0 [ 2.152832] i2c /dev entries driver [ 2.159301] Driver for 1-wire Dallas network protocol. [ 2.168212] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.177001] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.186126] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.196289] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.235412] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 2.244812] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@480d5000[0]' [ 2.254455] 480d5000.mmc supply vmmc not found, using dummy regulator [ 2.261444] omap_hsmmc 480d5000.mmc: could not set regulator OCR (-22) [ 2.268341] omap_hsmmc 480d5000.mmc: pins are not configured from the driver [ 2.276184] omap_hsmmc 480d5000.mmc: could not set regulator OCR (-22) [ 2.313201] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.316070] ledtrig-cpu: registered to indicate activity on CPUs [ 2.316528] usbcore: registered new interface driver usbhid [ 2.316528] usbhid: USB HID core driver [ 2.318023] oprofile: no performance counters [ 2.318908] oprofile: using timer interrupt. [ 2.319488] TCP: cubic registered [ 2.319488] Initializing XFRM netlink socket [ 2.319641] NET: Registered protocol family 17 [ 2.319702] NET: Registered protocol family 15 [ 2.319976] Key type dns_resolver registered [ 2.320709] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu [ 2.320709] omap2_set_init_voltage: unable to set vdd_mpu [ 2.320709] omap2_set_init_voltage: unable to find boot up OPP for vdd_core [ 2.320739] omap2_set_init_voltage: unable to set vdd_core [ 2.320739] omap2_set_init_voltage: unable to find boot up OPP for vdd_iva [ 2.320739] omap2_set_init_voltage: unable to set vdd_iva [ 2.322601] Power Management for TI OMAP4+ devices. [ 2.322662] Power Management for TI OMAP4. [ 2.322662] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 2.328186] ThumbEE CPU extension supported. [ 2.328186] Registering SWP/SWPB emulation handler [ 2.329223] SmartReflex Class3 initialized [ 2.350677] twl_rtc 48070000.i2c:twl@48:rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.350677] sr_init: No PMIC hook to init smartreflex [ 2.350708] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 2.350708] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 2.352142] smartreflex smartreflex.2: omap_sr_probe: SmartReflex driver initialized [ 2.390472] VUSB: disabling [ 2.391174] VANA: disabling [ 2.391845] VDAC: disabling [ 2.394592] VAUX1_6030: disabling [ 2.492340] mmc0: new high speed SDHC card at address 0007 %% Start PM consolidated quick test (retention only) %% Preparation