CCSending /srv/serial/u-boot-spl.bin, 784 blocks: Give your local XMODEM receive command now. Transfer complete t SPL 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 CSending: u-boot.bin Sending: Transfer complete m - CRC mode, 3(SOH)/375(STX)/0(CAN) packets, 3 retries Loaded 384084 bytes U-Boot 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 U-Boot# U-Boot# setenv autoload off; setenv serverip 192.168.57.1; dhcp cpsw Waiting for PHY auto negotiation to complete.. done link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.138 U-Boot# tftp 0x81000000 zImage.omap2plus_defconfig link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'zImage.omap2plus_defconfig'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################### 1.1 MiB/s done Bytes transferred = 4360800 (428a60 hex) U-Boot# tftp 0x82000000 am335x-bone.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'am335x-bone.dtb'. Load address: 0x82000000 Loading: *## 1 MiB/s done Bytes transferred = 28422 (6f06 hex) U-Boot# setenv bootargs console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp U-Boot# U-Boot# bootz 0x81000000 - 0x82000000 ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 82000000, end 82009f05 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.16.0-rc5-79508-g1795cd9 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed Jul 16 14:15:10 MDT 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: CMA: reserved 16 MiB at 8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c08bebc0, node_mem_map cfcf1000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] HighMem zone: 1048574 pages exceeds freesize 0 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @cfca1000 s14336 r8192 d14336 u36864 [ 0.000000] pcpu-alloc: s14336 r8192 d14336 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 224916K/261120K available (5655K kernel code, 681K rwdata, 2200K rodata, 406K init, 8209K bss, 36204K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc07b3f8c (7856 kB) [ 0.000000] .init : 0xc07b4000 - 0xc0819800 ( 406 kB) [ 0.000000] .data : 0xc081a000 - 0xc08c4530 ( 682 kB) [ 0.000000] .bss : 0xc08c4530 - 0xc10c8a20 (8210 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000020] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000090] OMAP clocksource: timer1 at 24000000 Hz [ 0.001296] Console: colour dummy device 80x30 [ 0.001377] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001394] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001408] ... MAX_LOCK_DEPTH: 48 [ 0.001421] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001435] ... CLASSHASH_SIZE: 4096 [ 0.001448] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001461] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001474] ... CHAINHASH_SIZE: 32768 [ 0.001487] memory used by lock dependency info: 5167 kB [ 0.001501] per task-struct memory footprint: 1152 bytes [ 0.001564] Calibrating delay loop... 548.04 BogoMIPS (lpj=2740224) [ 0.108559] pid_max: default: 32768 minimum: 301 [ 0.109215] Security Framework initialized [ 0.109413] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.109436] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.113070] CPU: Testing write buffer coherency: ok [ 0.114827] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.114996] Setting up static identity map for 0x8055be40 - 0x8055beb0 [ 0.120383] Brought up 1 CPUs [ 0.120409] SMP: Total of 1 processors activated. [ 0.120426] CPU: All CPU(s) started in SVC mode. [ 0.124637] devtmpfs: initialized [ 0.140208] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.201361] omap_hwmod: tptc0 using broken dt data from edma [ 0.201995] omap_hwmod: tptc1 using broken dt data from edma [ 0.202618] omap_hwmod: tptc2 using broken dt data from edma [ 0.213838] omap_hwmod: debugss: _wait_target_disable failed [ 0.275369] pinctrl core: initialized pinctrl subsystem [ 0.279563] regulator-dummy: no parameters [ 0.325132] NET: Registered protocol family 16 [ 0.335287] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.339286] cpuidle: using governor ladder [ 0.339328] cpuidle: using governor menu [ 0.355366] platform 49000000.edma: alias fck already exists [ 0.355417] platform 49000000.edma: alias fck already exists [ 0.355451] platform 49000000.edma: alias fck already exists [ 0.358722] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.360140] OMAP GPIO hardware version 0.1 [ 0.362010] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.364974] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.367698] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.384960] No ATAGs? [ 0.385005] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.460811] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.461808] of_get_named_gpiod_flags: can't parse gpios property of node '/fixedregulator@0[0]' [ 0.462692] vmmcsd_fixed: 3300 mV [ 0.467816] SCSI subsystem initialized [ 0.469316] usbcore: registered new interface driver usbfs [ 0.469609] usbcore: registered new interface driver hub [ 0.479507] usbcore: registered new device driver usb [ 0.481005] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 0.481069] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.487804] Switched to clocksource timer1 [ 0.766695] NET: Registered protocol family 2 [ 0.769680] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.769939] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.771190] TCP: Hash tables configured (established 2048 bind 2048) [ 0.771461] TCP: reno registered [ 0.771502] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.771846] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.773659] NET: Registered protocol family 1 [ 0.776503] RPC: Registered named UNIX socket transport module. [ 0.776534] RPC: Registered udp transport module. [ 0.776551] RPC: Registered tcp transport module. [ 0.776568] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.778930] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.785399] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.793114] VFS: Disk quotas dquot_6.5.2 [ 0.793350] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.796511] NFS: Registering the id_resolver key type [ 0.797051] Key type id_resolver registered [ 0.797077] Key type id_legacy registered [ 0.797305] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.798393] msgmni has been set to 471 [ 0.806476] io scheduler noop registered [ 0.806520] io scheduler deadline registered [ 0.806633] io scheduler cfq registered (default) [ 0.810125] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.814112] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.825270] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.825324] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/serial@44e09000[0]' [ 0.826084] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.589838] console [ttyO0] enabled [ 1.600391] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 1.649672] brd: module loaded [ 1.678181] loop: module loaded [ 1.685912] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.697727] usbcore: registered new interface driver asix [ 1.703651] usbcore: registered new interface driver ax88179_178a [ 1.710356] usbcore: registered new interface driver cdc_ether [ 1.716778] usbcore: registered new interface driver smsc95xx [ 1.723090] usbcore: registered new interface driver net1080 [ 1.729308] usbcore: registered new interface driver cdc_subset [ 1.735765] usbcore: registered new interface driver zaurus [ 1.742070] usbcore: registered new interface driver cdc_ncm [ 1.750543] usbcore: registered new interface driver cdc_wdm [ 1.756816] usbcore: registered new interface driver usb-storage [ 1.763712] usbcore: registered new interface driver usbtest [ 1.772887] mousedev: PS/2 mouse device common for all mice [ 1.784959] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 1.793540] i2c /dev entries driver [ 1.797351] Driver for 1-wire Dallas network protocol. [ 1.814254] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.823566] of_get_named_gpiod_flags exited with status 0 [ 1.829351] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@48060000[0]' [ 1.839941] omap_hsmmc 48060000.mmc: unable to get vmmc regulator -517 [ 1.847607] platform 48060000.mmc: Driver omap_hsmmc requests probe deferral [ 1.855884] of_get_named_gpiod_flags exited with status 0 [ 1.861661] of_get_named_gpiod_flags exited with status 0 [ 1.867341] of_get_named_gpiod_flags exited with status 0 [ 1.873070] of_get_named_gpiod_flags exited with status 0 [ 1.878805] of_get_named_gpiod_flags exited with status 0 [ 1.885645] of_get_named_gpiod_flags exited with status 0 [ 1.891977] of_get_named_gpiod_flags exited with status 0 [ 1.898219] of_get_named_gpiod_flags exited with status 0 [ 1.905198] ledtrig-cpu: registered to indicate activity on CPUs [ 1.912459] usbcore: registered new interface driver usbhid [ 1.918385] usbhid: USB HID core driver [ 1.924355] oprofile: using arm/armv7 [ 1.929216] TCP: cubic registered [ 1.932718] Initializing XFRM netlink socket [ 1.937343] NET: Registered protocol family 17 [ 1.942218] NET: Registered protocol family 15 [ 1.947374] Key type dns_resolver registered [ 1.952321] omap_voltage_late_init: Voltage driver support not added [ 1.959074] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize [ 1.967922] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize [ 1.978072] ThumbEE CPU extension supported. [ 1.982628] Registering SWP/SWPB emulation handler [ 1.987764] SmartReflex Class3 initialized [ 2.170509] DCDC1: at 1500 mV [ 2.177909] vdd_mpu: 925 <--> 1325 mV at 1100 mV [ 2.186037] vdd_core: 925 <--> 1150 mV at 1100 mV [ 2.194570] LDO1: at 1800 mV [ 2.201182] LDO2: at 3300 mV [ 2.207314] LDO3: 1800 <--> 3300 mV at 1800 mV [ 2.215432] LDO4: at 3300 mV [ 2.221746] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 2.227691] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.234835] of_get_named_gpiod_flags exited with status 0 [ 2.240676] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@48060000[0]' [ 2.367604] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.374026] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.383613] libphy: 4a101000.mdio: probed [ 2.388010] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.399723] cpsw 4a100000.ethernet: Detected MACID = 78:c5:e5:c3:1e:2a [ 2.411250] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.420775] sr_init: No PMIC hook to init smartreflex [ 2.426451] sr_init: platform driver register failed for SR [ 2.462344] net eth0: initializing cpsw version 1.12 (0) [ 2.548652] net eth0: phy found : id is : 0x7c0f1 [ 2.553813] libphy: PHY 4a101000.mdio:01 not found [ 2.558939] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 5.628264] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 5.647553] Sending DHCP requests ., OK [ 5.668113] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.138 [ 5.677086] IP-Config: Complete: [ 5.680654] device=eth0, hwaddr=78:c5:e5:c3:1e:2a, ipaddr=192.168.57.138, mask=255.255.255.0, gw=255.255.255.255 [ 5.691839] host=192.168.57.138, domain=example.org, nis-domain=(none) [ 5.699187] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.705942] nameserver0=192.168.57.1 [ 5.710654] vmmcsd_fixed: disabling [ 5.739323] VFS: Mounted root (nfs filesystem) on device 0:13. [ 5.748072] devtmpfs: mounted [ 5.752293] Freeing unused kernel memory: 404K (c07b4000 - c0819000) INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.477407] udevd[738]: starting version 175 [ ok . [....] Synthesizing the initial hotplug events...udevd[777]: error changing net interface name eth0 to eth4: Device or resource busy [ ok done. [....] Waiting for /dev to be fully populated...[ ok done. [....] Activating swap...[ ok done. [ 15.114092] random: nonblocking pool is initialized [....] Cleaning up temporary files... /tmp[ ok . [....] Activating lvm and md swap...[ ok done. [....] Checking file systems...fsck from util-linux 2.20.1 [ ok done. [....] Mounting local filesystems...[ ok done. [....] Activating swapfile swap...[ ok done. [....] Cleaning up temporary files...[ ok . [....] Setting kernel variables ...[ ok done. [....] Configuring network interfaces...[ ok done. [....] Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 [ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [....] Cleaning up temporary files...[ ok . [....] Starting network benchmark server[ ok . INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting network benchmark server[FAIL failed! [....] Starting system message bus: dbus[ ok . [....] Starting rpcbind daemon...[....] Already running.[ ok . [....] Starting NFS common utilities: statd idmapd[ ok . Debian GNU/Linux wheezy/sid armel ttyO0 armel login: