U-Boot 1.1.4 (Mar 18 2007 - 12:22:00) OMAP2430C-GP revision 3, PRCM #5A TI 2430SDP 1.1 Version + mDDR (Boot NOR) DRAM: 128 MB Flash: 192 MB NAND:64 MB In: serial Out: serial Err: serial Hit any key to stop autoboot: 3  0 OMAP243X SDP # OMAP243X SDP # setenv bootargs console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh OMAP243X SDP # loady ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... CSending: uImage-dtb.omap2430-sdp Sending: Transfer complete dem - CRC mode, 9(SOH)/4682(STX)/0(CAN) packets, 3 retries ## Total Size = 0x00492b4c = 4795212 Bytes OMAP243X SDP # bootm ## Booting image at 80000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4795148 Bytes = 4.6 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.0-rc3-01006-g0df1f24 (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed Nov 5 11:38:56 MST 2014 [ 0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP2430 SDP [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 86800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 32512 [ 0.000000] free_area_init_node: node 0, pgdat c0974000, node_mem_map c7df1000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] HighMem zone: 1048574 pages exceeds freesize 0 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP2430 [ 0.000000] [ 0.000000] PERCPU: Embedded 11 pages/cpu @c7d91000 s14976 r8192 d21888 u45056 [ 0.000000] pcpu-alloc: s14976 r8192 d21888 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32256 [ 0.000000] Kernel command line: console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] allocated 260096 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 93856K/130048K available (6251K kernel code, 678K rwdata, 2320K rodata, 420K init, 8264K bss, 36192K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0866ec8 (8572 kB) [ 0.000000] .init : 0xc0867000 - 0xc08d0000 ( 420 kB) [ 0.000000] .data : 0xc08d0000 - 0xc0979bd8 ( 679 kB) [ 0.000000] .bss : 0xc0979bd8 - 0xc118bc28 (8265 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000061] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000579] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.002899] Console: colour dummy device 80x30 [ 0.003082] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.003112] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.003143] ... MAX_LOCK_DEPTH: 48 [ 0.003173] ... MAX_LOCKDEP_KEYS: 8191 [ 0.003204] ... CLASSHASH_SIZE: 4096 [ 0.003234] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.003265] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.003295] ... CHAINHASH_SIZE: 32768 [ 0.003326] memory used by lock dependency info: 5167 kB [ 0.003356] per task-struct memory footprint: 1152 bytes [ 0.003448] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816) [ 0.125152] pid_max: default: 32768 minimum: 301 [ 0.126342] Security Framework initialized [ 0.126892] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.126983] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.137145] Initializing cgroup subsys memory [ 0.137359] Initializing cgroup subsys devices [ 0.137695] Initializing cgroup subsys freezer [ 0.138000] Initializing cgroup subsys blkio [ 0.138275] Initializing cgroup subsys perf_event [ 0.138580] CPU: Testing write buffer coherency: ok [ 0.143280] missing device node for CPU 0 [ 0.143371] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366 [ 0.143615] Setting up static identity map for 0x805ec300 - 0x805ec370 [ 0.157440] Brought up 1 CPUs [ 0.157470] SMP: Total of 1 processors activated. [ 0.157531] CPU: All CPU(s) started in SVC mode. [ 0.169616] devtmpfs: initialized [ 0.177520] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 0.287506] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3) [ 0.319793] pinctrl core: initialized pinctrl subsystem [ 0.329620] regulator-dummy: no parameters [ 0.479583] NET: Registered protocol family 16 [ 0.501312] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.509033] cpuidle: using governor ladder [ 0.509124] cpuidle: using governor menu [ 0.581359] omap_gpio 4900c000.gpio: Could not get gpio dbck [ 0.585052] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.588409] OMAP GPIO hardware version 2.4 [ 0.591339] omap_gpio 4900e000.gpio: Could not get gpio dbck [ 0.592864] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.598358] omap_gpio 49010000.gpio: Could not get gpio dbck [ 0.599609] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.605010] omap_gpio 49012000.gpio: Could not get gpio dbck [ 0.606445] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.611694] omap_gpio 480b6000.gpio: Could not get gpio dbck [ 0.613067] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.618896] omap-gpmc 6e000000.gpmc: GPMC revision 3.0 [ 0.620178] omap-gpmc 6e000000.gpmc: ethernet using bootloader timings on CS5 [ 0.635131] No ATAGs? [ 0.635345] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.635375] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.641845] OMAP DMA hardware revision 4.0 [ 0.720367] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.720581] edma-dma-engine: probe of edma-dma-engine.0 failed with error -22 [ 0.849914] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.864074] SCSI subsystem initialized [ 0.866607] usbcore: registered new interface driver usbfs [ 0.867218] usbcore: registered new interface driver hub [ 0.867645] usbcore: registered new device driver usb [ 0.877716] omap_i2c 48070000.i2c: bus 0 rev3.3 at 100 kHz [ 0.891296] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz [ 0.907501] Switched to clocksource 32k_counter [ 1.418670] NET: Registered protocol family 2 [ 1.424652] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.425170] TCP bind hash table entries: 1024 (order: 3, 36864 bytes) [ 1.426605] TCP: Hash tables configured (established 1024 bind 1024) [ 1.427307] TCP: reno registered [ 1.427429] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.428192] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.432434] NET: Registered protocol family 1 [ 1.437744] RPC: Registered named UNIX socket transport module. [ 1.437805] RPC: Registered udp transport module. [ 1.437835] RPC: Registered tcp transport module. [ 1.437896] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.442413] hw perfevents: enabled with armv6_1136 PMU driver, 3 counters available [ 1.460968] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.461669] audit: initializing netlink subsys (disabled) [ 1.462341] audit: type=2000 audit(1.450:1): initialized [ 1.476806] VFS: Disk quotas dquot_6.5.2 [ 1.477539] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.486022] NFS: Registering the id_resolver key type [ 1.487731] Key type id_resolver registered [ 1.487792] Key type id_legacy registered [ 1.488433] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.495391] msgmni has been set to 215 [ 1.509704] io scheduler noop registered [ 1.509796] io scheduler deadline registered [ 1.510101] io scheduler cfq registered (default) [ 1.520904] pinctrl-single 49002030.pinmux: 340 pins at pa fb002030 size 340 [ 1.530944] pbias_mmc_omap2430: 1800 <--> 3000 mV at 3000 mV [ 1.536804] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.558105] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.558227] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 1.559844] omap_uart 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 29, base_baud = 3000000) is a OMAP UART0 [ 2.436645] console [ttyO0] enabled [ 2.447631] omap_uart 4806c000.serial: no wakeirq for uart0 [ 2.453582] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 2.464447] omap_uart 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 30, base_baud = 3000000) is a OMAP UART1 [ 2.479370] omap_uart 4806e000.serial: no wakeirq for uart0 [ 2.485321] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 2.496124] omap_uart 4806e000.serial: ttyO2 at MMIO 0x4806e000 (irq = 31, base_baud = 3000000) is a OMAP UART2 [ 2.515594] omap_rng 480a0000.rng: OMAP Random Number Generator ver. 50 [ 2.602020] brd: module loaded [ 2.652282] loop: module loaded [ 2.693267] twl 1-0048: PIH (irq 216) chaining IRQs 217..225 [ 2.700622] twl 1-0048: power (irq 222) chaining IRQs 225..232 [ 2.724182] VAUX1: at 3000 mV [ 2.735839] VAUX2_4030: at 2800 mV [ 2.747741] VAUX3: at 2800 mV [ 2.758972] VAUX4: at 1200 mV [ 2.770416] VDD1: 600 <--> 1450 mV at 1300 mV [ 2.783081] VDAC: 1800 mV [ 2.797180] VIO: at 1800 mV [ 2.809387] VINTANA1: 1500 mV [ 2.821472] VINTANA2: at 2750 mV [ 2.834136] VINTDIG: 1500 mV [ 2.843933] VMMC1: 1850 <--> 3150 mV at 1850 mV [ 2.856811] VMMC2: 1850 <--> 3150 mV at 2600 mV [ 2.868743] VUSB1V5: 1500 mV [ 2.877288] VUSB1V8: 1800 mV [ 2.885955] VUSB3V1: 3100 mV [ 2.897979] VPLL1: at 1300 mV [ 2.911987] VPLL2: 1800 mV [ 2.922912] VSIM: 1800 <--> 3000 mV at 1800 mV [ 2.934631] twl4030_gpio twl4030-gpio: gpio (irq 217) chaining IRQs 233..250 [ 2.944396] gpiochip_find_base: found new base at 494 [ 2.951843] gpiochip_add: registered GPIOs 494 to 511 on device: twl4030 [ 2.988342] mtdoops: mtd device (mtddev=name/number) must be supplied [ 3.013366] smc91x 8000300.ethernet: GPIO lookup for consumer power [ 3.020202] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.027252] of_get_named_gpiod_flags: can't parse 'power-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.038696] of_get_named_gpiod_flags: can't parse 'power-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.049987] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.057556] smc91x 8000300.ethernet: lookup for GPIO power failed [ 3.064056] smc91x 8000300.ethernet: GPIO lookup for consumer reset [ 3.070800] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.077819] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.089233] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.100494] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.107666] smc91x 8000300.ethernet: lookup for GPIO reset failed [ 3.114257] smc91x 8000300.ethernet (unnamed net_device) (uninitialized): smc91x: IOADDR c887a300 doesn't match configuration (0). [ 3.126770] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre [ 3.141632] smc91x 8000300.ethernet eth0: SMC91C94 (rev 9) at c887a300 IRQ 197 [ 3.149414] [ 3.151031] smc91x 8000300.ethernet eth0: Ethernet addr: 10:03:31:33:16:8f [ 3.163940] usbcore: registered new interface driver asix [ 3.170349] usbcore: registered new interface driver ax88179_178a [ 3.177459] usbcore: registered new interface driver cdc_ether [ 3.184265] usbcore: registered new interface driver smsc95xx [ 3.190948] usbcore: registered new interface driver net1080 [ 3.197540] usbcore: registered new interface driver cdc_subset [ 3.204254] usbcore: registered new interface driver zaurus [ 3.211090] usbcore: registered new interface driver cdc_ncm [ 3.221496] usbcore: registered new interface driver cdc_wdm [ 3.228363] usbcore: registered new interface driver usb-storage [ 3.235351] usbcore: registered new interface driver usbtest [ 3.249359] mousedev: PS/2 mouse device common for all mice [ 3.258697] twl4030_keypad 48072000.i2c:twl@48:keypad: OF: linux,keymap property not defined in /ocp/i2c@48072000/twl@48/keypad [ 3.270935] twl4030_keypad 48072000.i2c:twl@48:keypad: Failed to build keymap [ 3.278778] twl4030_keypad: probe of 48072000.i2c:twl@48:keypad failed with error -2 [ 3.298370] input: twl4030_pwrbutton as /devices/ocp/48072000.i2c/i2c-1/1-0048/48072000.i2c:twl@48:pwrbutton/input/input1 [ 3.319152] twl_rtc 48072000.i2c:twl@48:rtc: Power up reset detected. [ 3.326690] twl_rtc 48072000.i2c:twl@48:rtc: Enabling TWL-RTC [ 3.349029] twl_rtc 48072000.i2c:twl@48:rtc: rtc core: registered 48072000.i2c:twl@48 as rtc0 [ 3.361938] i2c /dev entries driver [ 3.372650] Driver for 1-wire Dallas network protocol. [ 3.394653] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.404449] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.467926] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.477691] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.488830] 480b4000.mmc supply vmmc not found, using dummy regulator [ 3.496734] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.505157] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.550018] ledtrig-cpu: registered to indicate activity on CPUs [ 3.558288] usbcore: registered new interface driver usbhid [ 3.564178] usbhid: USB HID core driver [ 3.573760] oprofile: using arm/armv6 [ 3.580108] TCP: cubic registered [ 3.583740] Initializing XFRM netlink socket [ 3.589660] NET: Registered protocol family 10 [ 3.605560] sit: IPv6 over IPv4 tunneling driver [ 3.618133] NET: Registered protocol family 17 [ 3.623077] NET: Registered protocol family 15 [ 3.629119] Key type dns_resolver registered [ 3.634246] SmartReflex Class3 initialized [ 3.673400] twl_rtc 48072000.i2c:twl@48:rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.683624] sr_init: No PMIC hook to init smartreflex [ 3.689971] sr_init: platform driver register failed for SR [ 3.820770] VUSB3V1: disabling [ 3.826843] VUSB1V8: disabling [ 3.833099] VUSB1V5: disabling [ 3.856567] Waiting for root device /dev/mmcblk0p1... %% Start PM consolidated quick test (retention only) %% Preparation