CCSending /srv/serial/u-boot-spl.bin, 784 blocks: Give your local XMODEM receive command now. Transfer complete Boot SPL 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 CSending: u-boot.bin Sending: Transfer complete m - CRC mode, 3(SOH)/375(STX)/0(CAN) packets, 3 retries Loaded 384084 bytes U-Boot 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 Card did not respond to voltage select! mmc0(part 0) is current device mmc_send_cmd : timeout: No status update Card did not respond to voltage select! Booting from nand ... no devices available Wrong Image Format for bootm command ERROR: can't get kernel image! U-Boot# a askenv - get environment variables from stdin Usage: askenv name [message] [size] - get environment variable 'name' from stdin (max 'size' chars) U-Boot# setenv autoload off; setenv serverip 192.168.57.1; dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.138 U-Boot# tftp 0x81000000 zImage.omap2plus_defconfig link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'zImage.omap2plus_defconfig'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 872.1 KiB/s done Bytes transferred = 4629896 (46a588 hex) U-Boot# tftp 0x82000000 am335x-bone.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'am335x-bone.dtb'. Load address: 0x82000000 Loading: *### 774.4 KiB/s done Bytes transferred = 29369 (72b9 hex) U-Boot# setenv bootargs console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp U-Boot# U-Boot# bootz 0x81000000 - 0x82000000 ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 82000000, end 8200a2b8 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.0-rc7-next-20141205-116906-gf97d3a7 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Fri Dec 12 14:08:14 MST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c0943cc0, node_mem_map cfcb1000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 11 pages/cpu @cfc5f000 s14912 r8192 d21952 u45056 [ 0.000000] pcpu-alloc: s14912 r8192 d21952 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64704 [ 0.000000] Kernel command line: console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 224108K/261120K available (6070K kernel code, 678K rwdata, 2300K rodata, 428K init, 8218K bss, 20628K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0834df8 (8372 kB) [ 0.000000] .init : 0xc0835000 - 0xc08a0000 ( 428 kB) [ 0.000000] .data : 0xc08a0000 - 0xc09499f8 ( 679 kB) [ 0.000000] .bss : 0xc09499f8 - 0xc1150388 (8219 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000021] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000095] OMAP clocksource: timer1 at 24000000 Hz [ 0.001327] Console: colour dummy device 80x30 [ 0.001408] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001423] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001437] ... MAX_LOCK_DEPTH: 48 [ 0.001450] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001463] ... CLASSHASH_SIZE: 4096 [ 0.001475] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001488] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001500] ... CHAINHASH_SIZE: 32768 [ 0.001513] memory used by lock dependency info: 5167 kB [ 0.001527] per task-struct memory footprint: 1152 bytes [ 0.001565] Calibrating delay loop... 545.58 BogoMIPS (lpj=2727936) [ 0.098319] pid_max: default: 32768 minimum: 301 [ 0.098910] Security Framework initialized [ 0.099182] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.099210] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.103379] Initializing cgroup subsys memory [ 0.103500] Initializing cgroup subsys devices [ 0.103630] Initializing cgroup subsys freezer [ 0.103769] Initializing cgroup subsys blkio [ 0.103889] Initializing cgroup subsys perf_event [ 0.104009] CPU: Testing write buffer coherency: ok [ 0.105931] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.106095] Setting up static identity map for 0x805c0450 - 0x805c04c0 [ 0.111981] Brought up 1 CPUs [ 0.112015] CPU: All CPU(s) started in SVC mode. [ 0.116413] devtmpfs: initialized [ 0.120411] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.181651] omap_hwmod: tptc0 using broken dt data from edma [ 0.182297] omap_hwmod: tptc1 using broken dt data from edma [ 0.182921] omap_hwmod: tptc2 using broken dt data from edma [ 0.194262] omap_hwmod: debugss: _wait_target_disable failed [ 0.257970] pinctrl core: initialized pinctrl subsystem [ 0.309051] NET: Registered protocol family 16 [ 0.318956] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.322175] cpuidle: using governor ladder [ 0.322223] cpuidle: using governor menu [ 0.333851] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.335228] OMAP GPIO hardware version 0.1 [ 0.337305] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.340544] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.343456] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.363810] No ATAGs? [ 0.363859] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.432608] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.433757] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator@0[0]' [ 0.439463] SCSI subsystem initialized [ 0.440658] usbcore: registered new interface driver usbfs [ 0.440948] usbcore: registered new interface driver hub [ 0.441158] usbcore: registered new device driver usb [ 0.442506] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 0.442568] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.449154] Switched to clocksource timer1 [ 0.686228] NET: Registered protocol family 2 [ 0.688879] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.689283] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.690532] TCP: Hash tables configured (established 2048 bind 2048) [ 0.690840] TCP: reno registered [ 0.690885] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.691230] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.693069] NET: Registered protocol family 1 [ 0.695345] RPC: Registered named UNIX socket transport module. [ 0.695380] RPC: Registered udp transport module. [ 0.695397] RPC: Registered tcp transport module. [ 0.695413] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.697657] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.704386] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.704725] audit: initializing netlink subsys (disabled) [ 0.705064] audit: type=2000 audit(0.700:1): initialized [ 0.712045] VFS: Disk quotas dquot_6.5.2 [ 0.712277] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.715761] NFS: Registering the id_resolver key type [ 0.716284] Key type id_resolver registered [ 0.716308] Key type id_legacy registered [ 0.716577] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.723414] io scheduler noop registered [ 0.723467] io scheduler deadline registered [ 0.723623] io scheduler cfq registered (default) [ 0.726978] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.731482] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.740628] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.740686] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@44e09000[0]' [ 0.741469] omap_uart 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 154, base_baud = 3000000) is a OMAP UART0 [ 1.510809] console [ttyO0] enabled [ 1.521250] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20 [ 1.563253] brd: module loaded [ 1.587184] loop: module loaded [ 1.594887] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.606081] usbcore: registered new interface driver asix [ 1.612086] usbcore: registered new interface driver ax88179_178a [ 1.618665] usbcore: registered new interface driver cdc_ether [ 1.625117] usbcore: registered new interface driver smsc95xx [ 1.631407] usbcore: registered new interface driver net1080 [ 1.637532] usbcore: registered new interface driver cdc_subset [ 1.643977] usbcore: registered new interface driver zaurus [ 1.650206] usbcore: registered new interface driver cdc_ncm [ 1.657790] usbcore: registered new interface driver cdc_wdm [ 1.664133] usbcore: registered new interface driver usb-storage [ 1.670766] usbcore: registered new interface driver usbtest [ 1.679771] mousedev: PS/2 mouse device common for all mice [ 1.691370] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 1.699856] i2c /dev entries driver [ 1.703633] Driver for 1-wire Dallas network protocol. [ 1.713234] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.721558] Driver 'mmcblk' needs updating - please use bus_type methods [ 1.729981] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.740363] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 1.751638] omap_hsmmc 48060000.mmc: unable to get vmmc regulator -517 [ 1.759535] platform 48060000.mmc: Driver omap_hsmmc requests probe deferral [ 1.767860] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led@2[0]' - status (0) [ 1.778540] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led@3[0]' - status (0) [ 1.788668] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led@4[0]' - status (0) [ 1.798721] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led@5[0]' - status (0) [ 1.809411] ledtrig-cpu: registered to indicate activity on CPUs [ 1.816544] usbcore: registered new interface driver usbhid [ 1.822455] usbhid: USB HID core driver [ 1.828347] oprofile: using arm/armv7 [ 1.833300] TCP: cubic registered [ 1.836843] Initializing XFRM netlink socket [ 1.841592] NET: Registered protocol family 17 [ 1.846376] NET: Registered protocol family 15 [ 1.851598] Key type dns_resolver registered [ 1.856464] omap_voltage_late_init: Voltage driver support not added [ 1.863209] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize [ 1.871719] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize [ 1.881809] ThumbEE CPU extension supported. [ 1.886341] Registering SWP/SWPB emulation handler [ 1.891466] SmartReflex Class3 initialized [ 1.950649] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 1.956364] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 1.963630] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.974020] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 2.099125] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.105540] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.115728] libphy: 4a101000.mdio: probed [ 2.120125] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.132016] cpsw 4a100000.ethernet: Detected MACID = 78:c5:e5:c3:1e:2a [ 2.143889] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.153044] sr_init: No PMIC hook to init smartreflex [ 2.158718] sr_init: platform driver register failed for SR [ 2.200610] net eth0: initializing cpsw version 1.12 (0) [ 2.209034] net eth0: phy found : id is : 0x7c0f1 [ 2.214166] libphy: PHY 4a101000.mdio:01 not found [ 2.219247] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 5.289738] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 5.309024] Sending DHCP requests ., OK [ 5.329584] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.138 [ 5.338539] IP-Config: Complete: [ 5.342046] device=eth0, hwaddr=78:c5:e5:c3:1e:2a, ipaddr=192.168.57.138, mask=255.255.255.0, gw=255.255.255.255 [ 5.353191] host=192.168.57.138, domain=example.org, nis-domain=(none) [ 5.360513] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.367257] nameserver0=192.168.57.1 [ 5.371962] vmmcsd_fixed: disabling [ 5.402340] VFS: Mounted root (nfs filesystem) on device 0:13. [ 5.411109] devtmpfs: mounted [ 5.415403] Freeing unused kernel memory: 428K (c0835000 - c08a0000) INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.383545] udevd[141]: starting version 175 [ ok . [....] Synthesizing the initial hotplug events...udevd[187]: error changing net interface name eth0 to eth4: Device or resource busy [ ok done. [....] Waiting for /dev to be fully populated...[ ok done. [ 15.329538] random: nonblocking pool is initialized [....] Activating swap...[ ok done. [....] Cleaning up temporary files... /tmp[ ok . [....] Activating lvm and md swap...[ ok done. [....] Checking file systems...fsck from util-linux 2.20.1 [ ok done. [....] Mounting local filesystems...[ ok done. [....] Activating swapfile swap...[ ok done. [....] Cleaning up temporary files...[ ok . [....] Setting kernel variables ...[ ok done. [....] Configuring network interfaces...[ ok done. [....] Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 [ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [....] Cleaning up temporary files...[ ok . [....] Starting network benchmark server[ ok . INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting network benchmark server[FAIL failed! [....] Starting system message bus: dbus[ ok . [....] Starting rpcbind daemon...[....] Already running.[ ok . [....] Starting NFS common utilities: statd idmapd[ ok . Debian GNU/Linux wheezy/sid armel ttyO0 armel login: