Texas Instruments X-Loader 1.47 (Jan 14 2011 - 15:43:28) Starting X-loader on MMC Reading boot sector 212836 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... U-Boot 2010.06 (Jan 14 2011 - 15:43:45) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 EVM board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB In: serial Out: serial Err: serial Read back SMSC id 0x92200000 Die ID #368000229ff80000016071640902c013 Net: smc911x-0 Hit any key to stop autoboot: 3  0 OMAP3_EVM # OMAP3_EVM # setenv bootfile uImage-dtb.omap3-evm-37xx OMAP3_EVM # OMAP3_EVM # dhcp smc911x: detected LAN9220 controller smc911x: phy initialized smc911x: MAC 00:50:c2:7e:99:42 BOOTP broadcast 1 DHCP client bound to address 192.168.57.131 Using smc911x-0 device TFTP from server 192.168.57.1; our IP address is 192.168.57.131 Filename 'uImage-dtb.omap3-evm-37xx'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################## done Bytes transferred = 4791469 (491cad hex) OMAP3_EVM # setenv bootargs console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh OMAP3_EVM # OMAP3_EVM # bootm ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4791405 Bytes = 4.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.19.0-rc7-119240-ge36f014 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed Feb 4 21:37:04 MST 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP37XX EVM (TMDSEVM3730) [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c09718c0, node_mem_map cfcb1000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] PERCPU: Embedded 11 pages/cpu @cfc3b000 s14912 r8192 d21952 u45056 [ 0.000000] pcpu-alloc: s14912 r8192 d21952 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64704 [ 0.000000] Kernel command line: console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 223740K/261120K available (6194K kernel code, 677K rwdata, 2360K rodata, 428K init, 8221K bss, 20996K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0862de8 (8556 kB) [ 0.000000] .init : 0xc0863000 - 0xc08ce000 ( 428 kB) [ 0.000000] .data : 0xc08ce000 - 0xc09776e8 ( 678 kB) [ 0.000000] .bss : 0xc09776e8 - 0xc117ee50 (8222 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001251] Console: colour dummy device 80x30 [ 0.001312] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001342] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001342] ... MAX_LOCK_DEPTH: 48 [ 0.001342] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001373] ... CLASSHASH_SIZE: 4096 [ 0.001373] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001403] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001403] ... CHAINHASH_SIZE: 32768 [ 0.001403] memory used by lock dependency info: 5167 kB [ 0.001434] per task-struct memory footprint: 1152 bytes [ 0.001464] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696) [ 0.097564] pid_max: default: 32768 minimum: 301 [ 0.098083] Security Framework initialized [ 0.098327] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.098358] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.102508] Initializing cgroup subsys memory [ 0.102600] Initializing cgroup subsys devices [ 0.102722] Initializing cgroup subsys freezer [ 0.102844] Initializing cgroup subsys blkio [ 0.102935] Initializing cgroup subsys perf_event [ 0.103057] CPU: Testing write buffer coherency: ok [ 0.104736] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.104888] Setting up static identity map for 0x805decd0 - 0x805ded40 [ 0.109649] Brought up 1 CPUs [ 0.109680] SMP: Total of 1 processors activated (594.73 BogoMIPS). [ 0.109710] CPU: All CPU(s) started in SVC mode. [ 0.113769] devtmpfs: initialized [ 0.125457] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.208557] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.210906] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.320098] pinctrl core: initialized pinctrl subsystem [ 0.421356] NET: Registered protocol family 16 [ 0.430389] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.433288] cpuidle: using governor ladder [ 0.433349] cpuidle: using governor menu [ 0.441741] Reprogramming SDRC clock to 400000000 Hz [ 0.455078] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.456481] OMAP GPIO hardware version 2.5 [ 0.458496] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.461334] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.464050] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.466705] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.469512] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.471069] irq: no irq domain found for /ocp/pinmux@48002030 ! [ 0.471954] irq: no irq domain found for /ocp/pinmux@48002030 ! [ 0.472839] irq: no irq domain found for /ocp/pinmux@48002030 ! [ 0.497406] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 0.502044] platform 48058000.ssi-controller: Cannot lookup hwmod 'ssi' [ 0.510742] No ATAGs? [ 0.510772] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.514404] OMAP DMA hardware revision 5.0 [ 0.604827] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.606109] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vddvario[0]' [ 0.607482] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vdd33a[0]' [ 0.608612] reg-fixed-voltage wl12xx_vmmc: could not find pctldev for node /ocp/pinmux@48002030/pinmux_wl12xx_gpio, deferring probe [ 0.608673] platform wl12xx_vmmc: Driver reg-fixed-voltage requests probe deferral [ 0.608947] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-lcd-3v3[0]' - status (0) [ 0.615570] SCSI subsystem initialized [ 0.616424] libata version 3.00 loaded. [ 0.617645] usbcore: registered new interface driver usbfs [ 0.617889] usbcore: registered new interface driver hub [ 0.618072] usbcore: registered new device driver usb [ 0.624847] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz [ 0.626403] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz [ 0.630584] omap_i2c 48060000.i2c: bus 2 rev4.4 at 400 kHz [ 0.637054] Switched to clocksource 32k_counter [ 0.853759] NET: Registered protocol family 2 [ 0.856048] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.856292] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.857543] TCP: Hash tables configured (established 2048 bind 2048) [ 0.857818] TCP: reno registered [ 0.857879] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.858184] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.859863] NET: Registered protocol family 1 [ 0.861816] RPC: Registered named UNIX socket transport module. [ 0.861846] RPC: Registered udp transport module. [ 0.861877] RPC: Registered tcp transport module. [ 0.861877] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.863891] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.872131] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.872467] audit: initializing netlink subsys (disabled) [ 0.872802] audit: type=2000 audit(0.860:1): initialized [ 0.879028] VFS: Disk quotas dquot_6.5.2 [ 0.879241] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.882507] NFS: Registering the id_resolver key type [ 0.883026] Key type id_resolver registered [ 0.883056] Key type id_legacy registered [ 0.883270] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.889190] io scheduler noop registered [ 0.889221] io scheduler deadline registered [ 0.889373] io scheduler cfq registered (default) [ 0.893371] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568 [ 0.894165] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92 [ 0.895263] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size 92 [ 0.904846] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.914184] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.914825] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.800048] console [ttyO0] enabled [ 1.806640] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 1.817108] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 1.829101] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@49020000[0]' [ 1.839447] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 1.851287] omap_uart 49042000.serial: no wakeirq for uart0 [ 1.857269] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@49042000[0]' [ 1.867523] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3 [ 1.910583] brd: module loaded [ 1.933044] loop: module loaded [ 1.963592] twl 0-0048: PIH (irq 23) chaining IRQs 341..349 [ 1.970001] twl 0-0048: power (irq 346) chaining IRQs 349..356 [ 2.033508] twl4030_gpio twl4030-gpio: gpio (irq 341) chaining IRQs 357..374 [ 2.042144] gpiochip_find_base: found new base at 492 [ 2.048431] gpiochip_add: registered GPIOs 492 to 511 on device: twl4030 [ 2.119171] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.127288] nand: Could not find valid ONFI parameter page; aborting [ 2.134063] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xbc [ 2.140777] nand: Hynix NAND 512MiB 1,8V 16-bit [ 2.145568] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.153564] nand: using OMAP_ECC_BCH8_CODE_HW_DETECTION_SW [ 2.162200] 5 ofpart partitions found on MTD device omap2-nand.0 [ 2.168609] Creating 5 MTD partitions on "omap2-nand.0": [ 2.174194] 0x000000000000-0x000000080000 : "X-Loader" [ 2.187591] 0x000000080000-0x000000240000 : "U-Boot" [ 2.198730] 0x000000240000-0x000000280000 : "Environment" [ 2.209106] 0x000000280000-0x000000780000 : "Kernel" [ 2.222900] 0x000000780000-0x000020000000 : "Filesystem" [ 2.690093] libphy: smsc911x-mdio: probed [ 2.694824] smsc911x 2c000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=2c000000.etherne:01, irq=-1) [ 2.707305] smsc911x 2c000000.ethernet eth0: MAC Address: 00:50:c2:7e:99:42 [ 2.716766] usbcore: registered new interface driver asix [ 2.722747] usbcore: registered new interface driver ax88179_178a [ 2.729400] usbcore: registered new interface driver cdc_ether [ 2.735839] usbcore: registered new interface driver smsc95xx [ 2.742095] usbcore: registered new interface driver net1080 [ 2.748291] usbcore: registered new interface driver cdc_subset [ 2.754669] usbcore: registered new interface driver zaurus [ 2.760894] usbcore: registered new interface driver cdc_ncm [ 2.768463] usbcore: registered new interface driver cdc_wdm [ 2.774688] usbcore: registered new interface driver usb-storage [ 2.781402] usbcore: registered new interface driver usbtest [ 2.790802] mousedev: PS/2 mouse device common for all mice [ 2.799224] input: TWL4030 Keypad as /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:keypad/input/input0 [ 2.820159] input: twl4030_pwrbutton as /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:pwrbutton/input/input1 [ 2.836639] twl_rtc 48070000.i2c:twl@48:rtc: Power up reset detected. [ 2.843780] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC [ 2.854888] twl_rtc 48070000.i2c:twl@48:rtc: rtc core: registered 48070000.i2c:twl@48 as rtc0 [ 2.865203] i2c /dev entries driver [ 2.872283] Driver for 1-wire Dallas network protocol. [ 2.882171] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.892700] Driver 'mmcblk' needs updating - please use bus_type methods [ 2.901550] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.911254] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.967559] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.977233] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.987701] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 [ 2.995269] platform 480b4000.mmc: Driver omap_hsmmc requests probe deferral [ 3.004150] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/ledb[0]' - status (0) [ 3.021209] ledtrig-cpu: registered to indicate activity on CPUs [ 3.028808] usbcore: registered new interface driver usbhid [ 3.034667] usbhid: USB HID core driver [ 3.041534] oprofile: using arm/armv7 [ 3.046295] TCP: cubic registered [ 3.049957] Initializing XFRM netlink socket [ 3.054626] NET: Registered protocol family 17 [ 3.059478] NET: Registered protocol family 15 [ 3.064605] Key type dns_resolver registered [ 3.069641] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iva [ 3.077301] omap2_set_init_voltage: unable to set vdd_mpu_iva [ 3.083374] omap2_set_init_voltage: unable to find boot up OPP for vdd_core [ 3.090759] omap2_set_init_voltage: unable to set vdd_core [ 3.111480] ThumbEE CPU extension supported. [ 3.115997] Registering SWP/SWPB emulation handler [ 3.121093] SmartReflex Class3 initialized [ 3.132324] of_get_named_gpiod_flags: parsed 'gpio' property of node '/wl12xx_vmmc[0]' - status (0) [ 3.142944] vwl1271: supplied by VMMC2 [ 3.148406] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.158020] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.291259] twl_rtc 48070000.i2c:twl@48:rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.301239] sr_init: No PMIC hook to init smartreflex [ 3.307067] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 3.315887] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 3.393066] smsc911x 2c000000.ethernet eth0: SMSC911x/921x identified at 0xd087e000, IRQ: 288 [ 3.450408] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.459228] mmc0: new SDHC card at address e624 [ 3.467102] mmcblk0: mmc0:e624 SD08G 7.40 GiB [ 3.489410] mmcblk0: p1 p2 p3 [ 5.717254] Sending DHCP requests ., OK [ 5.747833] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.131 [ 5.757781] IP-Config: Complete: [ 5.761199] device=eth0, hwaddr=00:50:c2:7e:99:42, ipaddr=192.168.57.131, mask=255.255.255.0, gw=255.255.255.255 [ 5.772460] host=192.168.57.131, domain=example.org, nis-domain=(none) [ 5.779846] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.786621] nameserver0=192.168.57.1 [ 5.791778] vwl1271: disabling [ 5.797729] VUSB3V1: disabling [ 5.805236] lcd_3v3: disabling [ 5.852203] VFS: Mounted root (nfs filesystem) readonly on device 0:14. [ 5.862731] devtmpfs: mounted [ 5.868103] Freeing unused kernel memory: 428K (c0863000 - c08ce000) /bin/sh: 0: can't access tty; job control turned off #