U-Boot 1.1.4 (Mar 18 2007 - 12:22:00) OMAP2430C-GP revision 3, PRCM #5A TI 2430SDP 1.1 Version + mDDR (Boot NOR) DRAM: 128 MB Flash: 192 MB NAND:64 MB In: serial Out: serial Err: serial Hit any key to stop autoboot: 3  2  1  0 Using MAC Address 08:00:28:01:16:8F BOOTP broadcast 1 DHCP client bound to address 192.168.57.134 TFTP from server 192.168.57.1; our IP address is 192.168.57.134 Filename 'uImage.2430sdp'. Load address: 0x80000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# done Bytes transferred = 4056712 (3de688 hex) ## Booting image at 80000000 ... Image Name: Linux-3.6.0-rc6-00247-g1e2ee2a Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4056648 Bytes = 3.9 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.6.0-rc6-00247-g1e2ee2a (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 SMP Sun Sep 23 17:19:49 MDT 2012 [ 0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP2430 sdp2430 board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP2430 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz [ 0.000000] cm: Module associated with clock apll54_ck didn't enable in 100000 tries [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0e15000 s12736 r8192 d15936 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32256 [ 0.000000] Kernel command line: console=ttyO0,115200n8 earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 127MB = 127MB total [ 0.000000] Memory: 115488k/115488k available, 15584k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc06dab0c (6987 kB) [ 0.000000] .init : 0xc06db000 - 0xc072a1c0 ( 317 kB) [ 0.000000] .data : 0xc072c000 - 0xc07b5b80 ( 551 kB) [ 0.000000] .bss : 0xc07b5ba4 - 0xc0d1040c (5483 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.002441] Calibrating delay loop... 175.78 BogoMIPS (lpj=685568) [ 0.117065] pid_max: default: 32768 minimum: 301 [ 0.118377] Security Framework initialized [ 0.118804] Mount-cache hash table entries: 512 [ 0.131866] CPU: Testing write buffer coherency: ok [ 0.134307] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366 [ 0.134460] Setting up static identity map for 0x805006f0 - 0x80500760 [ 0.140106] Brought up 1 CPUs [ 0.140136] SMP: Total of 1 processors activated (175.78 BogoMIPS). [ 0.175628] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3) [ 0.197662] dummy: [ 0.203674] NET: Registered protocol family 16 [ 0.205383] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.205596] GPMC revision 3.0 [ 0.227630] omap_gpio omap_gpio.0: Could not get gpio dbck [ 0.233337] OMAP GPIO hardware version 2.4 [ 0.236907] omap_gpio omap_gpio.1: Could not get gpio dbck [ 0.244354] omap_gpio omap_gpio.2: Could not get gpio dbck [ 0.251007] omap_gpio omap_gpio.3: Could not get gpio dbck [ 0.257202] omap_gpio omap_gpio.4: Could not get gpio dbck [ 0.279815] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.288360] _omap_mux_get_by_name: Could not find signal sys_nirq [ 0.324554] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.324615] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.324645] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.324676] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.324707] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.324768] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.324798] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.324829] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.378509] OMAP DMA hardware revision 4.0 [ 0.573730] bio: create slab at 0 [ 0.848541] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.864532] SCSI subsystem initialized [ 0.872680] usbcore: registered new interface driver usbfs [ 0.874298] usbcore: registered new interface driver hub [ 0.876983] usbcore: registered new device driver usb [ 0.883880] omap_i2c omap_i2c.1: bus 1 rev1.3.7 at 100 kHz [ 0.892272] omap_i2c omap_i2c.2: bus 2 rev1.3.7 at 100 kHz [ 0.944854] twl 2-0048: PIH (irq 23) chaining IRQs 274..282 [ 0.946838] twl 2-0048: power (irq 279) chaining IRQs 282..289 [ 0.956085] twl4030_gpio twl4030_gpio: gpio (irq 274) chaining IRQs 290..307 [ 0.974426] VMMC1: 1850 <--> 3150 mV at 1850 mV normal standby [ 1.000671] Switching to clocksource 32k_counter [ 1.359558] NET: Registered protocol family 2 [ 1.365783] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 1.366607] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) [ 1.372772] TCP: Hash tables configured (established 4096 bind 4096) [ 1.373260] TCP: reno registered [ 1.373352] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.374176] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.376678] NET: Registered protocol family 1 [ 1.380340] RPC: Registered named UNIX socket transport module. [ 1.380401] RPC: Registered udp transport module. [ 1.380432] RPC: Registered tcp transport module. [ 1.380462] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.383758] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.918701] VFS: Disk quotas dquot_6.5.2 [ 1.919464] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.927551] NFS: Registering the id_resolver key type [ 1.928955] Key type id_resolver registered [ 1.929016] Key type id_legacy registered [ 1.929412] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.931427] msgmni has been set to 225 [ 1.941833] io scheduler noop registered [ 1.941894] io scheduler deadline registered [ 1.942108] io scheduler cfq registered (default) [ 1.948608] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.967773] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0 [ 2.710174] console [ttyO0] enabled [ 2.719268] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1 [ 2.731353] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 90) is a OMAP UART2 [ 2.839111] brd: module loaded [ 2.899627] loop: module loaded [ 2.919677] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.928955] OneNAND driver initializing [ 2.963470] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre [ 2.980651] eth0: SMC91C94 (rev 9) at c885e300 IRQ 263 [nowait] [ 2.987365] eth0: Ethernet addr: 08:00:28:01:16:8f [ 2.997772] usbcore: registered new interface driver asix [ 3.006286] usbcore: registered new interface driver cdc_ether [ 3.014495] usbcore: registered new interface driver smsc95xx [ 3.022369] usbcore: registered new interface driver net1080 [ 3.030120] usbcore: registered new interface driver cdc_subset [ 3.038177] usbcore: registered new interface driver zaurus [ 3.045959] usbcore: registered new interface driver cdc_ncm [ 3.058288] usbcore: registered new interface driver cdc_wdm [ 3.064605] Initializing USB Mass Storage driver... [ 3.071380] usbcore: registered new interface driver usb-storage [ 3.078033] USB Mass Storage support registered. [ 3.086090] usbcore: registered new interface driver libusual [ 3.094116] usbcore: registered new interface driver usbtest [ 3.105072] mousedev: PS/2 mouse device common for all mice [ 3.128509] input: twl4030_pwrbutton as /devices/platform/omap_i2c.2/i2c-2/2-0049/twl4030_pwrbutton/input/input0 [ 3.147460] twl_rtc twl_rtc: Power up reset detected. [ 3.153594] twl_rtc twl_rtc: Enabling TWL-RTC [ 3.171020] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 3.182342] i2c /dev entries driver [ 3.194274] Driver for 1-wire Dallas network protocol. [ 3.208648] omap_wdt: OMAP Watchdog Timer Rev 0x22: initial timeout 60 sec [ 3.219085] twl4030_wdt twl4030_wdt: Failed to register misc device [ 3.226135] twl4030_wdt: probe of twl4030_wdt failed with error -16 [ 3.241241] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 3.248779] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 3.438201] usbcore: registered new interface driver usbhid [ 3.444427] usbhid: USB HID core driver [ 3.448638] oprofile: hardware counters not available [ 3.453948] oprofile: using timer interrupt. [ 3.460540] TCP: cubic registered [ 3.464233] Initializing XFRM netlink socket [ 3.469116] NET: Registered protocol family 17 [ 3.474212] NET: Registered protocol family 15 [ 3.480072] Key type dns_resolver registered [ 3.485015] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 3.493591] mux: Failed to setup hwmod io irq -22 [ 3.516326] Power Management for OMAP2 initializing [ 3.521636] PRCM revision 1.0 [ 3.573883] clock: disabling unused clocks to save power [ 3.599395] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 3.614288] eth0: link up [ 3.634887] Sending DHCP requests ., OK [ 3.658966] IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.57.134 [ 3.668548] IP-Config: Complete: [ 3.671966] device=eth0, addr=192.168.57.134, mask=255.255.255.0, gw=255.255.255.255 [ 3.680755] host=192.168.57.134, domain=, nis-domain=(none) [ 3.687194] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 3.752075] VFS: Mounted root (nfs filesystem) on device 0:11. [ 3.760284] Freeing init memory: 316K [ 3.798431] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.808563] mmc0: new SDHC card at address e624 [ 3.871765] mmcblk0: mmc0:e624 SD04G 3.69 GiB [ 3.922393] mmcblk0: p1 /bin/sh: can't access tty; job control turned off #