$ NOLO X-Loader (v1.1.16, Oct 31 2008) Secondary image size 99036 Booting secondary Nokia OMAP Loader v1.1.16 (Oct 31 2008) running on Nokia N800 F5 (RX-34) Clocks: Core: 658 MHz L3: 109 MHz L4: 109 MHz MPU: 329 MHz DSP: 219 MHz IVA: 109 MHz I2C v3.4 Menelaus v2.2 found Vilma v1.5 found Betty v2.1 found Reset reason: pwr_key System DMA v2.0 OneNAND blocks unlocked in 30264 us Flash id: ec4811 Partition table successfully read McSPI v1.4 RFBI version 1.0 Detecting LCD panel lph8923 Panel ID: 838f48 URAL panel detected Detected LCD panel: ls041y3 S1D13745 Hailstorm detected FB memory blanking took 242 ms (3089 kB/s) Logo drawn in 24 ms (1218 kB/s) Über-cool backlight fade-in took 101 ms Initializing USB USB host detected Entering USB loop SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 64 bytes) SETUP: WR STD DEVICE SET_ADDRESS value 001d index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 18 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 9 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 94 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 00, index 0000, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 02, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 01, index 0409, length 255 bytes) SETUP: WR STD DEVICE SET_CONFIGURATION value 0001 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 03, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0001 index 0002 length 0000 Flashing interface selected SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 Flashing mode entered SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 SETUP: RD VND DEVICE req 04 value 0000 index 0000 length 0200 SETUP: RD VND DEVICE req 03 value 0000 index 0000 length 0004 SETUP: WR VND DEVICE req 12 value 0000 index 0000 length 0012 SETUP: RD VND DEVICE req 14 value 0000 index 0000 length 0200 SETUP: WR VND DEVICE req 42 value 0000 index 0000 length 001b Receiving kernel (length 2045952) Image successfully received SETUP: WR VND DEVICE req 82 value 0000 index 0000 length 0000 SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 Boot requested Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.6.0 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Sun Sep 30 18:36:38 MDT 2012 [ 0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Nokia N800 [ 0.000000] Ignoring unrecognised tag 0x414f4d50 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c0415798, node_mem_map c093e000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] OMAP2420 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttyO2,115200 earlyprintk debug init=/bin/bash [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 120432k/120432k available, 10640k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc03a5e18 (3704 kB) [ 0.000000] .init : 0xc03a6000 - 0xc03ccf4c ( 156 kB) [ 0.000000] .data : 0xc03ce000 - 0xc0416220 ( 289 kB) [ 0.000000] .bss : 0xc0416244 - 0xc093d0d8 (5276 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] NR_IRQS:474 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.063690] Calibrating delay loop... 218.45 BogoMIPS (lpj=851968) [ 0.121673] pid_max: default: 32768 minimum: 301 [ 0.127197] Security Framework initialized [ 0.131713] Mount-cache hash table entries: 512 [ 0.146484] CPU: Testing write buffer coherency: ok [ 0.153839] hw perfevents: enabled with v6 PMU driver, 3 counters available [ 0.161590] Setting up static identity map for 0x80293410 - 0x80293480 [ 0.183502] ttyO2 used as console in debug mode uart2 clocks will not be gated [ 0.212524] dummy: [ 0.219055] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.226531] GPMC revision 2.0 [ 0.230285] gpmc: irq-20 could not claim: err -22 [ 0.250915] omap_gpio omap_gpio.0: Could not get gpio dbck [ 0.260803] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.268493] OMAP GPIO hardware version 1.8 [ 0.273986] omap_gpio omap_gpio.1: Could not get gpio dbck [ 0.282287] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.291381] omap_gpio omap_gpio.2: Could not get gpio dbck [ 0.300109] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.308563] omap_gpio omap_gpio.3: Could not get gpio dbck [ 0.316375] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.338714] omap_mux_init: Add partition: #1: core, flags: 3 [ 0.404113] mmci-omap.0: alias fck already exists [ 0.411010] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.420196] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.429321] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.438446] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.447570] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.456665] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.465789] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.472930] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.515258] OMAP DMA hardware revision 2.0 [ 0.608245] bio: create slab at 0 [ 0.630950] SCSI subsystem initialized [ 0.639801] omap_i2c omap_i2c.1: bus 1 rev1.3.4 at 400 kHz [ 0.653381] omap_i2c omap_i2c.2: bus 2 rev1.3.4 at 400 kHz [ 0.671081] Switching to clocksource 32k_counter [ 0.821166] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.859710] VFS: Disk quotas dquot_6.5.2 [ 0.864227] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.873931] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.883117] msgmni has been set to 235 [ 0.896789] io scheduler noop registered [ 0.900970] io scheduler deadline registered [ 0.905792] io scheduler cfq registered (default) [ 0.921722] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.945892] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 0.958740] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 0.969635] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 74) is a OMAP UART2 [ 0.977844] console [ttyO2] enabled, bootconsole disabled [ 0.977844] console [ttyO2] enabled, bootconsole disabled [ 1.000061] omap_rng omap_rng: OMAP Random Number Generator ver. 40 [ 1.084045] brd: module loaded [ 1.132171] loop: module loaded [ 1.138641] Menelaus rev 2.2 [ 1.167144] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.176666] OneNAND driver initializing [ 1.182403] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c88c0000, freq 54 MHz [ 1.193908] OneNAND Manufacturer: Samsung (0xec) [ 1.198822] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48) [ 1.204437] OneNAND version = 0x0011 [ 1.208312] Chip support all block unlock [ 1.212646] onenand_wait: controller error! state 15 ctrl 0x0440 intr 0x8000 [ 1.221801] Scanning device for bad blocks [ 1.234466] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x39 addr8 0x0 [ 1.242858] OneNAND eraseblock 57 is an initial bad block [ 1.248718] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3a addr8 0x0 [ 1.257110] OneNAND eraseblock 58 is an initial bad block [ 1.262969] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3b addr8 0x0 [ 1.271331] OneNAND eraseblock 59 is an initial bad block [ 1.289825] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xa7 addr8 0x0 [ 1.298217] OneNAND eraseblock 167 is an initial bad block [ 1.305694] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xb5 addr8 0x0 [ 1.314056] OneNAND eraseblock 181 is an initial bad block [ 1.352539] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x1c9 addr8 0x0 [ 1.361022] OneNAND eraseblock 457 is an initial bad block [ 1.557525] Creating 5 MTD partitions on "omap2-onenand": [ 1.563385] 0x000000000000-0x000000020000 : "bootloader" [ 1.584960] 0x000000020000-0x000000080000 : "config" [ 1.601104] 0x000000080000-0x000000280000 : "kernel" [ 1.617828] 0x000000280000-0x000000680000 : "initfs" [ 1.634246] 0x000000680000-0x000010000000 : "rootfs" [ 1.686157] spi spi2.0: no RX DMA engine channel for McSPI [ 1.692169] omap2_mcspi omap2_mcspi.2: can't setup spi2.0, status -11 [ 1.699035] omap2_mcspi omap2_mcspi.2: can't create new device for p54spi [ 1.712341] mousedev: PS/2 mouse device common for all mice [ 1.730560] i2c /dev entries driver [ 1.741943] Driver for 1-wire Dallas network protocol. [ 1.755554] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec [ 1.769256] mmci-omap mmci-omap.0: unable to obtain TX DMA engine channel 61 [ 1.776916] mmci-omap mmci-omap.0: unable to obtain RX DMA engine channel 62 [ 1.890014] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.897491] mmci-omap mmci-omap.0: command timeout (CMD52) [ 1.921630] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.928253] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.934814] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.941314] mmci-omap mmci-omap.0: command timeout (CMD5) [ 1.972167] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 1.980834] mux: Failed to setup hwmod io irq -22 [ 1.998565] Power Management for OMAP2 initializing [ 2.003753] PRCM revision 1.0 [ 2.046173] clock: disabling unused clocks to save power [ 2.064300] /home/paul/linux/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.081512] Waiting for root device /dev/mmcblk0p1... [ 2.576690] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.585906] mmc0: new SDHC card at address 1234 [ 2.596679] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 2.616149] mmcblk0: p1 [ 2.628540] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.642700] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.656555] mmci-omap mmci-omap.0: command timeout (CMD8) [ 2.666687] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.674438] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.684906] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.691680] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.701873] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.708770] kjournald starting. Commit interval 5 seconds [ 2.714660] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.721771] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.728790] mmci-omap mmci-omap.0: command timeout (CMD55) [ 2.948547] mmci-omap mmci-omap.0: command timeout (CMD1) [ 2.955413] EXT3-fs (mmcblk0p1): using internal journal [ 2.962310] EXT3-fs (mmcblk0p1): recovery complete [ 2.967559] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode [ 2.975860] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 2.983459] Freeing init memory: 152K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#