$ ÿNOLO X-Loader (v1.1.16, Oct 31 2008) Secondary image size 99036 Booting secondary Nokia OMAP Loader v1.1.16 (Oct 31 2008) running on Nokia N800 F5 (RX-34) Clocks: Core: 658 MHz L3: 109 MHz L4: 109 MHz MPU: 329 MHz DSP: 219 MHz IVA: 109 MHz I2C v3.4 Menelaus v2.2 found Vilma v1.5 found Betty v2.1 found Reset reason: pwr_key System DMA v2.0 OneNAND blocks unlocked in 30264 us Flash id: ec4811 Partition table successfully read McSPI v1.4 RFBI version 1.0 Detecting LCD panel lph8923 Panel ID: 838f48 URAL panel detected Detected LCD panel: ls041y3 S1D13745 Hailstorm detected FB memory blanking took 242 ms (3089 kB/s) Logo drawn in 24 ms (1218 kB/s) Über-cool backlight fade-in took 101 ms Initializing USB USB host detected Entering USB loop SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 64 bytes) SETUP: WR STD DEVICE SET_ADDRESS value 0004 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR DEVICE (value 00, index 0000, length 18 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 9 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR CONFIGURATION (value 00, index 0000, length 94 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 00, index 0000, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 02, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 01, index 0409, length 255 bytes) SETUP: WR STD DEVICE SET_CONFIGURATION value 0001 index 0000 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 03, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: WR STD INTERFACE SET_INTERFACE value 0001 index 0002 length 0000 Flashing interface selected SETUP: RD STD DEVICE GET_DESCRIPTOR STRING (value 04, index 0409, length 255 bytes) SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 Flashing mode entered SETUP: RD VND DEVICE req 01 value 0000 index 0000 length 0004 SETUP: RD VND DEVICE req 04 value 0000 index 0000 length 0200 SETUP: RD VND DEVICE req 03 value 0000 index 0000 length 0004 SETUP: WR VND DEVICE req 12 value 0000 index 0000 length 0012 SETUP: RD VND DEVICE req 14 value 0000 index 0000 length 0200 SETUP: WR VND DEVICE req 42 value 0000 index 0000 length 001b Receiving kernel (length 2059136) Image successfully received SETUP: WR VND DEVICE req 82 value 0000 index 0000 length 0000 SETUP: WR STD INTERFACE SET_INTERFACE value 0000 index 0002 length 0000 Boot requested Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.8.0-rc5-12932-g949db15 (paul@nozomi) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Sat Jan 26 00:39:14 MST 2013 [ 0.000000] CPU: ARMv6-compatible processor [4107b362] revision 2 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Nokia N800 [ 0.000000] Ignoring unrecognised tag 0x414f4d50 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c03d72b0, node_mem_map c08f8000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] OMAP2420 [ 0.000000] [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 19.2/658/329 MHz [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttyO2,115200 earlyprintk debug init=/bin/bash ignore_loglevel [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 120712k/120712k available, 10360k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc03821ec (3561 kB) [ 0.000000] .init : 0xc0383000 - 0xc03a6f0c ( 144 kB) [ 0.000000] .data : 0xc03a8000 - 0xc03d7da0 ( 192 kB) [ 0.000000] .bss : 0xc03d7da0 - 0xc08f7870 (5247 kB) [ 0.000000] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 2.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.001831] Calibrating delay loop... 218.45 BogoMIPS (lpj=851968) [ 0.117034] pid_max: default: 32768 minimum: 301 [ 0.117858] Mount-cache hash table entries: 512 [ 0.122436] CPU: Testing write buffer coherency: ok [ 0.124694] Setting up static identity map for 0x802a89d0 - 0x802a8a2c [ 0.137664] ttyO2 used as console in debug mode: uart2 clocks will not be gated [ 0.172668] pinctrl core: initialized pinctrl subsystem [ 0.182647] regulator-dummy: no parameters [ 0.185943] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.188568] omap-gpmc omap-gpmc: GPMC revision 2.0 [ 0.206573] omap_gpio omap_gpio.0: Could not get gpio dbck [ 0.209472] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.210571] OMAP GPIO hardware version 1.8 [ 0.213043] omap_gpio omap_gpio.1: Could not get gpio dbck [ 0.215667] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.219085] omap_gpio omap_gpio.2: Could not get gpio dbck [ 0.221099] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.224456] omap_gpio omap_gpio.3: Could not get gpio dbck [ 0.226562] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.240264] omap_mux_init: Add partition: #1: core, flags: b [ 0.299255] mmci-omap.0: alias fck already exists [ 0.301055] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.301116] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.334594] OMAP DMA hardware revision 2.0 [ 0.401245] bio: create slab at 0 [ 0.638885] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.652679] SCSI subsystem initialized [ 0.663665] omap_i2c omap_i2c.1: bus 1 rev3.3 at 400 kHz [ 0.667205] omap_i2c omap_i2c.2: bus 2 rev3.3 at 400 kHz [ 0.675628] Switching to clocksource 32k_counter [ 0.817016] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.817596] CPU PMU: probing PMU on CPU 0 [ 0.817657] hw perfevents: enabled with v6 PMU driver, 3 counters available [ 1.067260] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.068878] msgmni has been set to 235 [ 1.072631] io scheduler noop registered [ 1.072692] io scheduler deadline registered [ 1.072814] io scheduler cfq registered (default) [ 1.080749] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.098266] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 88) is a OMAP UART0 [ 1.103454] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 89) is a OMAP UART1 [ 1.107971] omap_uart.2: ttyO2 at MMIO 0x4806e000 (irq = 90) is a OMAP UART2 [ 1.680908] console [ttyO2] enabled [ 1.694183] omap_rng omap_rng: OMAP Random Number Generator ver. 40 [ 1.705841] Menelaus rev 2.2 [ 1.739135] OneNAND driver initializing [ 1.745086] omap2-onenand omap2-onenand: initializing on CS0, phys base 0x04000000, virtual base c88c0000, freq 54 MHz [ 1.756591] OneNAND Manufacturer: Samsung (0xec) [ 1.761505] Muxed OneNAND(DDP) 256MB 1.8V 16-bit (0x48) [ 1.767150] OneNAND version = 0x0011 [ 1.771026] Chip support all block unlock [ 1.775390] onenand_wait: controller error! state 15 ctrl 0x0440 intr 0x8000 [ 1.784576] Scanning device for bad blocks [ 1.796966] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x39 addr8 0x0 [ 1.805358] OneNAND eraseblock 57 is an initial bad block [ 1.811248] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3a addr8 0x0 [ 1.819641] OneNAND eraseblock 58 is an initial bad block [ 1.825500] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x3b addr8 0x0 [ 1.833862] OneNAND eraseblock 59 is an initial bad block [ 1.853546] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xa7 addr8 0x0 [ 1.861938] OneNAND eraseblock 167 is an initial bad block [ 1.869567] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0xb5 addr8 0x0 [ 1.877929] OneNAND eraseblock 181 is an initial bad block [ 1.919311] onenand_bbt_wait: ecc 0x2222 ctrl 0x2440 intr 0x8080 addr1 0x1c9 addr8 0x0 [ 1.927795] OneNAND eraseblock 457 is an initial bad block [ 2.140808] Creating 5 MTD partitions on "omap2-onenand": [ 2.146667] 0x000000000000-0x000000020000 : "bootloader" [ 2.165618] 0x000000020000-0x000000080000 : "config" [ 2.180969] 0x000000080000-0x000000280000 : "kernel" [ 2.196685] 0x000000280000-0x000000680000 : "initfs" [ 2.212463] 0x000000680000-0x000010000000 : "rootfs" [ 2.259155] omap-dma-engine omap-dma-engine: allocating channel for 44 [ 2.266387] omap-dma-engine omap-dma-engine: allocating channel for 43 [ 2.285705] i2c /dev entries driver [ 2.296081] Driver for 1-wire Dallas network protocol. [ 2.311859] omap_wdt: OMAP Watchdog Timer Rev 0x11: initial timeout 60 sec [ 2.325714] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 2.332916] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 2.443847] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.451324] mmci-omap mmci-omap.0: command timeout (CMD52) [ 2.475891] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.482543] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.489166] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.495666] mmci-omap mmci-omap.0: command timeout (CMD5) [ 2.525024] oprofile: using arm/armv6 [ 2.529296] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 2.537841] mux: Failed to setup hwmod io irq -22 [ 2.554687] Power Management for OMAP2 initializing [ 2.560028] PRCM revision 1.0 [ 2.573608] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.585388] Waiting for root device /dev/mmcblk0p1... [ 3.115386] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.124603] mmc0: new SDHC card at address 1234 [ 3.134368] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 3.149902] mmcblk0: p1 [ 3.160522] mmci-omap mmci-omap.0: command timeout (CMD52) [ 3.167236] mmci-omap mmci-omap.0: command timeout (CMD52) [ 3.177978] mmci-omap mmci-omap.0: command timeout (CMD8) [ 3.184570] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.191101] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.197662] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.204223] mmci-omap mmci-omap.0: command timeout (CMD5) [ 3.210815] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.217468] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.224121] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.230804] mmci-omap mmci-omap.0: command timeout (CMD55) [ 3.239196] mmci-omap mmci-omap.0: command timeout (CMD1) [ 4.009246] kjournald starting. Commit interval 5 seconds [ 4.238952] EXT3-fs (mmcblk0p1): using internal journal [ 8.311218] EXT3-fs (mmcblk0p1): recovery complete [ 8.316314] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode [ 8.324493] VFS: Mounted root (ext3 filesystem) on device 179:1. [ 8.331909] Freeing init memory: 140K bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell root@(none):/#