U-Boot SPL 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) OMAP5432 ES2.0 U-Boot 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) CPU : OMAP5432 ES2.0 Board: CM-T54 I2C: ready DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 3  2  0 CM-T54 # CM-T54 # setenv bootargs 'console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh' CM-T54 # loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 115200 bps... CSending: uImage-dtb.omap5-sbc-t54 Sending: Transfer complete m - CRC mode, 7(SOH)/4441(STX)/0(CAN) packets, 3 retries ## Total Size = 0x0045661e = 4548126 Bytes CM-T54 # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4548062 Bytes = 4.3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.0.0-rc6-00153-ge42391c (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed Apr 1 18:09:28 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: CompuLab CM-T54 on SB-T54 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0xfe800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524031 [ 0.000000] free_area_init_node: node 0, pgdat c08fb000, node_mem_map ee5f9000 [ 0.000000] Normal zone: 1710 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 329471 pages, LIFO batch:31 [ 0.000000] OMAP5432 ES2.0 [ 0.000000] PERCPU: Embedded 12 pages/cpu @ee58e000 s18496 r8192 d22464 u49152 [ 0.000000] pcpu-alloc: s18496 r8192 d22464 u49152 alloc=12*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522321 [ 0.000000] Kernel command line: console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2042596K/2096124K available (5896K kernel code, 595K rwdata, 2264K rodata, 428K init, 8219K bss, 37144K reserved, 16384K cma-reserved, 1301500K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08005cc (8162 kB) [ 0.000000] .init : 0xc0801000 - 0xc086c000 ( 428 kB) [ 0.000000] .data : 0xc086c000 - 0xc0900ea8 ( 596 kB) [ 0.000000] .bss : 0xc0900ea8 - 0xc1107c10 (8220 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000457] Architected cp15 timer(s) running at 6.14MHz (virt). [ 0.000462] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 2796202663936ns [ 0.000473] Switching to timer-based delay loop, resolution 162ns [ 0.001523] Console: colour dummy device 80x30 [ 0.001555] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001563] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001569] ... MAX_LOCK_DEPTH: 48 [ 0.001575] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001581] ... CLASSHASH_SIZE: 4096 [ 0.001587] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001593] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001598] ... CHAINHASH_SIZE: 32768 [ 0.001604] memory used by lock dependency info: 5167 kB [ 0.001610] per task-struct memory footprint: 1152 bytes [ 0.001629] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440) [ 0.001642] pid_max: default: 32768 minimum: 301 [ 0.001907] Security Framework initialized [ 0.002032] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002044] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004094] Initializing cgroup subsys blkio [ 0.004117] Initializing cgroup subsys memory [ 0.004175] Initializing cgroup subsys devices [ 0.004230] Initializing cgroup subsys freezer [ 0.004314] Initializing cgroup subsys perf_event [ 0.004368] CPU: Testing write buffer coherency: ok [ 0.005204] /cpus/cpu@0 missing clock-frequency property [ 0.005224] /cpus/cpu@1 missing clock-frequency property [ 0.005235] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005293] Setting up static identity map for 0x805962c8 - 0x80596338 [ 0.009493] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.010033] Brought up 2 CPUs [ 0.010046] SMP: Total of 2 processors activated (24.57 BogoMIPS). [ 0.010053] CPU: All CPU(s) started in SVC mode. [ 0.012241] devtmpfs: initialized [ 0.013822] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.015145] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.016362] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.137565] pinctrl core: initialized pinctrl subsystem [ 0.180769] NET: Registered protocol family 16 [ 0.184175] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.210952] cpuidle: using governor ladder [ 0.240914] cpuidle: using governor menu [ 0.248309] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.248946] OMAP GPIO hardware version 0.1 [ 0.249859] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.251312] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.252653] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.253994] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.255337] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.256747] gpiochip_add: registered GPIOs 192 to 223 on device: gpio [ 0.258078] gpiochip_add: registered GPIOs 224 to 255 on device: gpio [ 0.259029] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc' [ 0.259226] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 0.259241] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.259318] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.283256] No ATAGs? [ 0.283311] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.283320] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.285287] OMAP DMA hardware revision 0.0 [ 0.350193] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.350837] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixed-regulator-mmcsd[0]' [ 0.351445] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 0.351872] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 0.353212] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 0.353253] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 0.353367] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 0.353700] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 0.354027] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 0.354058] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 0.354154] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/ads7846-reg[0]' [ 0.357479] SCSI subsystem initialized [ 0.357784] libata version 3.00 loaded. [ 0.358332] usb_phy_generic hsusb2_phy: GPIO lookup for consumer reset [ 0.358342] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.358370] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0) [ 0.358420] usb_phy_generic hsusb2_phy: GPIO lookup for consumer vbus-detect [ 0.358429] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.358439] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb2_phy[0]' [ 0.358448] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb2_phy[0]' [ 0.358457] usb_phy_generic hsusb2_phy: using lookup tables for GPIO lookup [ 0.358514] usb_phy_generic hsusb2_phy: lookup for GPIO vbus-detect failed [ 0.358554] hsusb2_phy supply vcc not found, using dummy regulator [ 0.358927] usb_phy_generic hsusb3_phy: GPIO lookup for consumer reset [ 0.358937] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.358962] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb3_phy[0]' - status (0) [ 0.358982] usb_phy_generic hsusb3_phy: GPIO lookup for consumer vbus-detect [ 0.358989] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.358999] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb3_phy[0]' [ 0.359008] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb3_phy[0]' [ 0.359016] usb_phy_generic hsusb3_phy: using lookup tables for GPIO lookup [ 0.359027] usb_phy_generic hsusb3_phy: lookup for GPIO vbus-detect failed [ 0.359055] hsusb3_phy supply vcc not found, using dummy regulator [ 0.359519] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c1_pins, deferring probe [ 0.359538] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 0.359587] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c2_pins, deferring probe [ 0.359605] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 0.360461] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 0.360617] omap_i2c 4807a000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c4_pins, deferring probe [ 0.360637] platform 4807a000.i2c: Driver omap_i2c requests probe deferral [ 0.361311] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 100 kHz [ 0.364222] Switched to clocksource arch_sys_counter [ 0.464073] NET: Registered protocol family 2 [ 0.465366] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.465568] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.467914] TCP: Hash tables configured (established 8192 bind 8192) [ 0.468043] TCP: reno registered [ 0.468064] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.468380] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.469292] NET: Registered protocol family 1 [ 0.470137] RPC: Registered named UNIX socket transport module. [ 0.470146] RPC: Registered udp transport module. [ 0.470154] RPC: Registered tcp transport module. [ 0.470161] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.497813] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.501823] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.502084] audit: initializing netlink subsys (disabled) [ 0.502184] audit: type=2000 audit(0.490:1): initialized [ 0.505202] VFS: Disk quotas dquot_6.5.2 [ 0.505304] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.506970] NFS: Registering the id_resolver key type [ 0.507180] Key type id_resolver registered [ 0.507189] Key type id_legacy registered [ 0.507307] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.510242] bounce: pool size: 64 pages [ 0.510293] io scheduler noop registered [ 0.510306] io scheduler deadline registered [ 0.510335] io scheduler cfq registered (default) [ 0.514898] pinctrl-single 4a002840.pinmux: 219 pins at pa fc002840 size 438 [ 0.515219] pinctrl-single 4ae0c840.pinmux: 28 pins at pa fce0c840 size 56 [ 0.519850] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.523984] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.524001] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.524364] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 306, base_baud = 3000000) is a OMAP UART0 [ 0.525495] omap_uart 4806c000.serial: no wakeirq for uart0 [ 0.525510] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 0.525691] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 307, base_baud = 3000000) is a OMAP UART1 [ 0.526460] omap_uart 48020000.serial: no wakeirq for uart0 [ 0.526474] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48020000[0]' [ 0.526654] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 308, base_baud = 3000000) is a OMAP UART2 [ 0.527397] omap_uart 4806e000.serial: no wakeirq for uart0 [ 0.527411] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 0.527599] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 309, base_baud = 3000000) is a OMAP UART3 [ 1.744374] console [ttyO3] enabled [ 1.748870] omap_uart 48066000.serial: no wakeirq for uart0 [ 1.754725] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48066000[0]' [ 1.764791] 48066000.serial: ttyO4 at MMIO 0x48066000 (irq = 310, base_baud = 3000000) is a OMAP UART4 [ 1.775428] omap_uart 48068000.serial: no wakeirq for uart0 [ 1.781261] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48068000[0]' [ 1.791272] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 311, base_baud = 3000000) is a OMAP UART5 [ 1.819992] brd: module loaded [ 1.835312] loop: module loaded [ 1.840598] ahci 4a140000.sata: forcing PORTS_IMPL to 0x1 [ 1.846347] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.855292] ahci 4a140000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst [ 1.866892] scsi host0: ahci [ 1.870772] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 335 [ 1.880045] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.896273] mousedev: PS/2 mouse device common for all mice [ 1.902107] i2c /dev entries driver [ 1.907085] Driver 'mmcblk' needs updating - please use bus_type methods [ 1.915025] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 1.921303] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.928177] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 1.938504] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 1.943334] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 1.949621] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.956476] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 1.966773] omap_hsmmc 4809c000.mmc: Got WP GPIO [ 1.971950] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 1.979064] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.986633] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 1.992914] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 1.999747] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.009306] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.018767] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.025787] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 2.031887] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 2.038177] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 2.045015] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.054572] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.064024] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.071036] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 2.114448] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.120762] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.127646] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.137220] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.146724] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.153764] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.159912] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.166241] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.173096] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.182690] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.192194] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.199248] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.205672] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.212604] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.220264] ledtrig-cpu: registered to indicate activity on CPUs [ 2.228016] oprofile: using timer interrupt. [ 2.232841] TCP: cubic registered [ 2.234161] ata1: SATA link down (SStatus 0 SControl 300) [ 2.241985] Initializing XFRM netlink socket [ 2.246543] NET: Registered protocol family 17 [ 2.251225] NET: Registered protocol family 15 [ 2.256072] Key type dns_resolver registered [ 2.260657] omap_vc_init_channel: No PMIC info for vdd_core [ 2.266500] omap_vp_init: No PMIC info for vdd_core [ 2.271616] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.277276] omap_vp_init: No PMIC info for vdd_mm [ 2.282212] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.287963] omap_vp_init: No PMIC info for vdd_mpu [ 2.293573] Power Management for TI OMAP4+ devices. [ 2.298910] ThumbEE CPU extension supported. [ 2.303418] Registering SWP/SWPB emulation handler [ 2.303430] mmc0: MAN_BKOPS_EN bit is not set [ 2.313042] SmartReflex Class3 initialized [ 2.321080] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.332513] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 2.341142] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 2.349972] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 2.359507] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.370287] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 2.378237] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 2.386673] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 2.396840] mmc0: new high speed MMC card at address 0001 [ 2.398981] palmas 0-0048: Irq flag is 0x00000000 [ 2.408942] mmcblk0: mmc0:0001 SEM08G 7.28 GiB [ 2.413952] mmcblk0boot0: mmc0:0001 SEM08G partition 1 2.00 MiB [ 2.420556] mmcblk0boot1: mmc0:0001 SEM08G partition 2 2.00 MiB [ 2.435818] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.486425] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.493769] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz [ 2.501146] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 2.507454] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 2.513749] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.520634] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.531012] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.535870] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 2.542166] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.549050] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.559384] omap_hsmmc 4809c000.mmc: Got WP GPIO [ 2.605048] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.611346] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.618211] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.627837] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.637365] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.644418] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.650545] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.656892] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.663768] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.673389] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.682919] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.689968] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.696349] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.703354] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.710925] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.722145] vwlan_pdn_fixed: supplied by ldo2 [ 2.727170] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.737975] vwlan_fixed: supplied by vwlan_pdn_fixed [ 2.743835] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.750162] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.757032] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.766636] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.776156] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.783185] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.789324] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.795640] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.802502] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.812095] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.821599] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.821631] mmc1: host does not support reading read-only switch, assuming write-enable [ 2.837050] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.843267] mmc1: new high speed SDHC card at address 0002 [ 2.849996] mmcblk1: mmc1:0002 00000 3.66 GiB [ 2.856675] mmcblk1: p1 p2 [ 2.895706] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.902282] sr_init: No PMIC hook to init smartreflex [ 2.907796] sr_init: platform driver register failed for SR [ 2.928052] mmc2: new high speed SDIO card at address 0001 [ 2.943141] ads7846-reg: disabling [ 2.953531] kjournald starting. Commit interval 5 seconds [ 2.953651] EXT3-fs (mmcblk1p2): mounted filesystem with ordered data mode [ 2.953717] VFS: Mounted root (ext3 filesystem) readonly on device 179:26. [ 2.974182] devtmpfs: mounted [ 2.977667] Freeing unused kernel memory: 428K (c0801000 - c086c000) /bin/sh: can't access tty; job control turned off / # / # / #