U-Boot SPL 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) OMAP5432 ES2.0 U-Boot 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) CPU : OMAP5432 ES2.0 Board: CM-T54 I2C: ready DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 3  0 CM-T54 # CM-T54 # setenv bootargs 'console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh' CM-T54 # loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 115200 bps... CSending: uImage-dtb.omap5-sbc-t54 Sending: Transfer complete m - CRC mode, 2(SOH)/4442(STX)/0(CAN) packets, 3 retries ## Total Size = 0x004567d6 = 4548566 Bytes CM-T54 # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4548502 Bytes = 4.3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.0.0-rc7-130664-gf22e6e8 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Tue Apr 7 15:49:56 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: CompuLab CM-T54 on SB-T54 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0xfe800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524031 [ 0.000000] free_area_init_node: node 0, pgdat c08fb0c0, node_mem_map ee5f9000 [ 0.000000] Normal zone: 1710 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 329471 pages, LIFO batch:31 [ 0.000000] OMAP5432 ES2.0 [ 0.000000] PERCPU: Embedded 12 pages/cpu @ee58e000 s18496 r8192 d22464 u49152 [ 0.000000] pcpu-alloc: s18496 r8192 d22464 u49152 alloc=12*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522321 [ 0.000000] Kernel command line: console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2042596K/2096124K available (5896K kernel code, 595K rwdata, 2264K rodata, 428K init, 8219K bss, 37144K reserved, 16384K cma-reserved, 1301500K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08005fc (8162 kB) [ 0.000000] .init : 0xc0801000 - 0xc086c000 ( 428 kB) [ 0.000000] .data : 0xc086c000 - 0xc0900f68 ( 596 kB) [ 0.000000] .bss : 0xc0900f68 - 0xc1107cd0 (8220 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000457] Architected cp15 timer(s) running at 6.14MHz (virt). [ 0.000462] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 2796202663936ns [ 0.000473] Switching to timer-based delay loop, resolution 162ns [ 0.001520] Console: colour dummy device 80x30 [ 0.001552] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001559] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001565] ... MAX_LOCK_DEPTH: 48 [ 0.001571] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001577] ... CLASSHASH_SIZE: 4096 [ 0.001583] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001588] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001594] ... CHAINHASH_SIZE: 32768 [ 0.001600] memory used by lock dependency info: 5167 kB [ 0.001606] per task-struct memory footprint: 1152 bytes [ 0.001624] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440) [ 0.001638] pid_max: default: 32768 minimum: 301 [ 0.001902] Security Framework initialized [ 0.002027] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002039] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004125] Initializing cgroup subsys blkio [ 0.004148] Initializing cgroup subsys memory [ 0.004207] Initializing cgroup subsys devices [ 0.004263] Initializing cgroup subsys freezer [ 0.004347] Initializing cgroup subsys perf_event [ 0.004402] CPU: Testing write buffer coherency: ok [ 0.005258] /cpus/cpu@0 missing clock-frequency property [ 0.005278] /cpus/cpu@1 missing clock-frequency property [ 0.005289] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005346] Setting up static identity map for 0x80596548 - 0x805965b8 [ 0.009522] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.010075] Brought up 2 CPUs [ 0.010087] SMP: Total of 2 processors activated (24.57 BogoMIPS). [ 0.010094] CPU: All CPU(s) started in SVC mode. [ 0.012343] devtmpfs: initialized [ 0.013916] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.015238] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.016455] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.136271] pinctrl core: initialized pinctrl subsystem [ 0.179578] NET: Registered protocol family 16 [ 0.183002] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.210966] cpuidle: using governor ladder [ 0.240929] cpuidle: using governor menu [ 0.248329] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.248972] OMAP GPIO hardware version 0.1 [ 0.249885] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.251341] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.252685] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.254034] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.255378] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.256798] gpiochip_add: registered GPIOs 192 to 223 on device: gpio [ 0.258131] gpiochip_add: registered GPIOs 224 to 255 on device: gpio [ 0.259083] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc' [ 0.259277] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 0.259292] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.259370] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.283267] No ATAGs? [ 0.283322] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.283332] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.285300] OMAP DMA hardware revision 0.0 [ 0.350245] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.350889] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixed-regulator-mmcsd[0]' [ 0.351494] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 0.351919] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 0.353262] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 0.353302] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 0.353416] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 0.353753] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 0.354082] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 0.354113] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 0.354210] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/ads7846-reg[0]' [ 0.357536] SCSI subsystem initialized [ 0.357843] libata version 3.00 loaded. [ 0.358388] usb_phy_generic hsusb2_phy: GPIO lookup for consumer reset [ 0.358398] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.358426] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0) [ 0.358476] usb_phy_generic hsusb2_phy: GPIO lookup for consumer vbus-detect [ 0.358485] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.358495] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb2_phy[0]' [ 0.358504] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb2_phy[0]' [ 0.358512] usb_phy_generic hsusb2_phy: using lookup tables for GPIO lookup [ 0.358570] usb_phy_generic hsusb2_phy: lookup for GPIO vbus-detect failed [ 0.358609] hsusb2_phy supply vcc not found, using dummy regulator [ 0.358986] usb_phy_generic hsusb3_phy: GPIO lookup for consumer reset [ 0.358996] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.359019] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb3_phy[0]' - status (0) [ 0.359038] usb_phy_generic hsusb3_phy: GPIO lookup for consumer vbus-detect [ 0.359046] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.359056] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb3_phy[0]' [ 0.359065] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb3_phy[0]' [ 0.359073] usb_phy_generic hsusb3_phy: using lookup tables for GPIO lookup [ 0.359083] usb_phy_generic hsusb3_phy: lookup for GPIO vbus-detect failed [ 0.359111] hsusb3_phy supply vcc not found, using dummy regulator [ 0.359578] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c1_pins, deferring probe [ 0.359598] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 0.359646] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c2_pins, deferring probe [ 0.359664] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 0.360517] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 0.360673] omap_i2c 4807a000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c4_pins, deferring probe [ 0.360693] platform 4807a000.i2c: Driver omap_i2c requests probe deferral [ 0.361370] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 100 kHz [ 0.364316] Switched to clocksource arch_sys_counter [ 0.464394] NET: Registered protocol family 2 [ 0.465599] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.465802] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.468148] TCP: Hash tables configured (established 8192 bind 8192) [ 0.468286] TCP: reno registered [ 0.468307] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.468623] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.469518] NET: Registered protocol family 1 [ 0.470371] RPC: Registered named UNIX socket transport module. [ 0.470381] RPC: Registered udp transport module. [ 0.470389] RPC: Registered tcp transport module. [ 0.470396] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.497250] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.501256] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.501494] audit: initializing netlink subsys (disabled) [ 0.501608] audit: type=2000 audit(0.490:1): initialized [ 0.504604] VFS: Disk quotas dquot_6.5.2 [ 0.504700] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.506386] NFS: Registering the id_resolver key type [ 0.506595] Key type id_resolver registered [ 0.506603] Key type id_legacy registered [ 0.506729] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.509637] bounce: pool size: 64 pages [ 0.509686] io scheduler noop registered [ 0.509700] io scheduler deadline registered [ 0.509728] io scheduler cfq registered (default) [ 0.514278] pinctrl-single 4a002840.pinmux: 219 pins at pa fc002840 size 438 [ 0.514601] pinctrl-single 4ae0c840.pinmux: 28 pins at pa fce0c840 size 56 [ 0.519262] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.523381] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.523397] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.523716] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 306, base_baud = 3000000) is a OMAP UART0 [ 0.524928] omap_uart 4806c000.serial: no wakeirq for uart0 [ 0.524944] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 0.525131] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 307, base_baud = 3000000) is a OMAP UART1 [ 0.525872] omap_uart 48020000.serial: no wakeirq for uart0 [ 0.525886] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48020000[0]' [ 0.526063] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 308, base_baud = 3000000) is a OMAP UART2 [ 0.526814] omap_uart 4806e000.serial: no wakeirq for uart0 [ 0.526828] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 0.527007] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 309, base_baud = 3000000) is a OMAP UART3 [ 1.743143] console [ttyO3] enabled [ 1.747648] omap_uart 48066000.serial: no wakeirq for uart0 [ 1.753478] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48066000[0]' [ 1.763536] 48066000.serial: ttyO4 at MMIO 0x48066000 (irq = 310, base_baud = 3000000) is a OMAP UART4 [ 1.774127] omap_uart 48068000.serial: no wakeirq for uart0 [ 1.779971] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48068000[0]' [ 1.789978] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 311, base_baud = 3000000) is a OMAP UART5 [ 1.818639] brd: module loaded [ 1.833886] loop: module loaded [ 1.839197] ahci 4a140000.sata: forcing PORTS_IMPL to 0x1 [ 1.844942] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.853851] ahci 4a140000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst [ 1.865541] scsi host0: ahci [ 1.869396] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 335 [ 1.878489] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.894989] mousedev: PS/2 mouse device common for all mice [ 1.900813] i2c /dev entries driver [ 1.905800] Driver 'mmcblk' needs updating - please use bus_type methods [ 1.913712] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 1.920000] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.926846] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 1.937172] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 1.942001] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 1.948292] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.955141] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 1.965432] omap_hsmmc 4809c000.mmc: Got WP GPIO [ 1.970596] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 1.977711] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.985283] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 1.991559] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 1.998392] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.007947] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.017400] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.024419] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 2.030519] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 2.036813] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 2.043631] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.053191] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.062655] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.069666] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 2.114520] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.120843] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.127713] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.137283] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.146771] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.153802] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.159942] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.166261] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.173118] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.182709] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.192201] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.199248] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.205661] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.212597] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.220238] ledtrig-cpu: registered to indicate activity on CPUs [ 2.227999] oprofile: using timer interrupt. [ 2.232821] TCP: cubic registered [ 2.234259] ata1: SATA link down (SStatus 0 SControl 300) [ 2.241942] Initializing XFRM netlink socket [ 2.246496] NET: Registered protocol family 17 [ 2.251174] NET: Registered protocol family 15 [ 2.256027] Key type dns_resolver registered [ 2.260613] omap_vc_init_channel: No PMIC info for vdd_core [ 2.266452] omap_vp_init: No PMIC info for vdd_core [ 2.271559] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.277217] omap_vp_init: No PMIC info for vdd_mm [ 2.282146] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.287898] omap_vp_init: No PMIC info for vdd_mpu [ 2.293497] Power Management for TI OMAP4+ devices. [ 2.298819] ThumbEE CPU extension supported. [ 2.303331] Registering SWP/SWPB emulation handler [ 2.303338] mmc0: MAN_BKOPS_EN bit is not set [ 2.312950] SmartReflex Class3 initialized [ 2.318821] mmc0: new high speed MMC card at address 0001 [ 2.326296] mmcblk0: mmc0:0001 SEM08G 7.28 GiB [ 2.326447] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.327084] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 2.327793] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 2.327844] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 2.328187] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.328587] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 2.328988] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 2.329019] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 2.336938] palmas 0-0048: Irq flag is 0x00000000 [ 2.408272] mmcblk0boot0: mmc0:0001 SEM08G partition 1 2.00 MiB [ 2.414854] mmcblk0boot1: mmc0:0001 SEM08G partition 2 2.00 MiB [ 2.428716] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.481097] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.488504] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz [ 2.495799] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 2.502115] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 2.508433] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.515311] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.525682] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.530538] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 2.536860] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.543729] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.554064] omap_hsmmc 4809c000.mmc: Got WP GPIO [ 2.605055] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.611352] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.618212] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.627800] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.637283] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.644329] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.650446] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.656752] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.663595] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.673180] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.681988] mmc1: host does not support reading read-only switch, assuming write-enable [ 2.684310] mmc1: new high speed SDHC card at address 0002 [ 2.691226] mmcblk1: mmc1:0002 00000 3.66 GiB [ 2.701479] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.708520] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.714895] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.721889] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.729452] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.740620] vwlan_pdn_fixed: supplied by ldo2 [ 2.745625] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.756709] vwlan_fixed: supplied by vwlan_pdn_fixed [ 2.757524] mmcblk1: p1 p2 [ 2.765505] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.771800] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.778665] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.788246] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.797743] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.804784] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.810895] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.817209] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.824056] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.833642] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.843136] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.850173] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.895735] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.902301] sr_init: No PMIC hook to init smartreflex [ 2.907806] sr_init: platform driver register failed for SR [ 2.927676] mmc2: new high speed SDIO card at address 0001 [ 2.943188] ads7846-reg: disabling [ 2.954909] kjournald starting. Commit interval 5 seconds [ 2.960836] EXT3-fs (mmcblk1p2): mounted filesystem with ordered data mode [ 2.968135] VFS: Mounted root (ext3 filesystem) readonly on device 179:26. [ 2.977813] devtmpfs: mounted [ 2.981296] Freeing unused kernel memory: 428K (c0801000 - c086c000) /bin/sh: can't access tty; job control turned off / # / # / #