U-Boot SPL 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) OMAP5432 ES2.0 U-Boot 2014.04-cm-t54-1 (May 13 2014 - 13:59:07) CPU : OMAP5432 ES2.0 Board: CM-T54 I2C: ready DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 3  0 CM-T54 # CM-T54 # setenv bootargs 'console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh' CM-T54 # loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 115200 bps... CSending: uImage-dtb.omap5-sbc-t54 Sending: Transfer complete - CRC mode, 2(SOH)/4442(STX)/0(CAN) packets, 3 retries ## Total Size = 0x004567e6 = 4548582 Bytes CM-T54 # bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4548518 Bytes = 4.3 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.0.0-rc7-130664-gf22e6e8 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Tue Apr 21 07:20:20 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: CompuLab CM-T54 on SB-T54 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0xfe800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 524031 [ 0.000000] free_area_init_node: node 0, pgdat c08fb0c0, node_mem_map ee5f9000 [ 0.000000] Normal zone: 1710 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 329471 pages, LIFO batch:31 [ 0.000000] OMAP5432 ES2.0 [ 0.000000] PERCPU: Embedded 12 pages/cpu @ee58e000 s18496 r8192 d22464 u49152 [ 0.000000] pcpu-alloc: s18496 r8192 d22464 u49152 alloc=12*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522321 [ 0.000000] Kernel command line: console=ttyO3,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2042596K/2096124K available (5896K kernel code, 595K rwdata, 2264K rodata, 428K init, 8219K bss, 37144K reserved, 16384K cma-reserved, 1301500K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08005fc (8162 kB) [ 0.000000] .init : 0xc0801000 - 0xc086c000 ( 428 kB) [ 0.000000] .data : 0xc086c000 - 0xc0900f68 ( 596 kB) [ 0.000000] .bss : 0xc0900f68 - 0xc1107cd0 (8220 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000457] Architected cp15 timer(s) running at 6.14MHz (virt). [ 0.000462] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 2796202663936ns [ 0.000473] Switching to timer-based delay loop, resolution 162ns [ 0.001522] Console: colour dummy device 80x30 [ 0.001554] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001560] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001566] ... MAX_LOCK_DEPTH: 48 [ 0.001572] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001578] ... CLASSHASH_SIZE: 4096 [ 0.001584] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001590] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001595] ... CHAINHASH_SIZE: 32768 [ 0.001601] memory used by lock dependency info: 5167 kB [ 0.001607] per task-struct memory footprint: 1152 bytes [ 0.001626] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440) [ 0.001639] pid_max: default: 32768 minimum: 301 [ 0.001901] Security Framework initialized [ 0.002028] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002040] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004116] Initializing cgroup subsys blkio [ 0.004139] Initializing cgroup subsys memory [ 0.004198] Initializing cgroup subsys devices [ 0.004253] Initializing cgroup subsys freezer [ 0.004337] Initializing cgroup subsys perf_event [ 0.004392] CPU: Testing write buffer coherency: ok [ 0.005245] /cpus/cpu@0 missing clock-frequency property [ 0.005265] /cpus/cpu@1 missing clock-frequency property [ 0.005275] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005333] Setting up static identity map for 0x80596548 - 0x805965b8 [ 0.009524] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.010073] Brought up 2 CPUs [ 0.010086] SMP: Total of 2 processors activated (24.57 BogoMIPS). [ 0.010093] CPU: All CPU(s) started in SVC mode. [ 0.012343] devtmpfs: initialized [ 0.013926] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.015251] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.016468] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.136308] pinctrl core: initialized pinctrl subsystem [ 0.179702] NET: Registered protocol family 16 [ 0.183138] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.210963] cpuidle: using governor ladder [ 0.240929] cpuidle: using governor menu [ 0.248334] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.248979] OMAP GPIO hardware version 0.1 [ 0.249895] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.251350] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.252690] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.254039] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.255386] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.256801] gpiochip_add: registered GPIOs 192 to 223 on device: gpio [ 0.258137] gpiochip_add: registered GPIOs 224 to 255 on device: gpio [ 0.259089] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc' [ 0.259282] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 0.259298] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.259376] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.283282] No ATAGs? [ 0.283337] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.283346] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.285314] OMAP DMA hardware revision 0.0 [ 0.350290] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.350934] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixed-regulator-mmcsd[0]' [ 0.351543] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 0.351972] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 0.353314] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 0.353353] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 0.353468] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 0.353801] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 0.354129] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 0.354161] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 0.354258] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/ads7846-reg[0]' [ 0.357593] SCSI subsystem initialized [ 0.357898] libata version 3.00 loaded. [ 0.358444] usb_phy_generic hsusb2_phy: GPIO lookup for consumer reset [ 0.358454] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.358481] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0) [ 0.358530] usb_phy_generic hsusb2_phy: GPIO lookup for consumer vbus-detect [ 0.358540] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.358549] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb2_phy[0]' [ 0.358559] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb2_phy[0]' [ 0.358567] usb_phy_generic hsusb2_phy: using lookup tables for GPIO lookup [ 0.358626] usb_phy_generic hsusb2_phy: lookup for GPIO vbus-detect failed [ 0.358663] hsusb2_phy supply vcc not found, using dummy regulator [ 0.359045] usb_phy_generic hsusb3_phy: GPIO lookup for consumer reset [ 0.359054] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.359078] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb3_phy[0]' - status (0) [ 0.359097] usb_phy_generic hsusb3_phy: GPIO lookup for consumer vbus-detect [ 0.359105] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.359114] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb3_phy[0]' [ 0.359123] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb3_phy[0]' [ 0.359131] usb_phy_generic hsusb3_phy: using lookup tables for GPIO lookup [ 0.359141] usb_phy_generic hsusb3_phy: lookup for GPIO vbus-detect failed [ 0.359169] hsusb3_phy supply vcc not found, using dummy regulator [ 0.359635] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c1_pins, deferring probe [ 0.359656] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 0.359704] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c2_pins, deferring probe [ 0.359722] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 0.360573] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 0.360728] omap_i2c 4807a000.i2c: could not find pctldev for node /ocp/pinmux@4a002840/pinmux_i2c4_pins, deferring probe [ 0.360747] platform 4807a000.i2c: Driver omap_i2c requests probe deferral [ 0.361423] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 100 kHz [ 0.364362] Switched to clocksource arch_sys_counter [ 0.464420] NET: Registered protocol family 2 [ 0.465632] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.465835] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.468180] TCP: Hash tables configured (established 8192 bind 8192) [ 0.468311] TCP: reno registered [ 0.468333] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.468650] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.469558] NET: Registered protocol family 1 [ 0.470402] RPC: Registered named UNIX socket transport module. [ 0.470411] RPC: Registered udp transport module. [ 0.470419] RPC: Registered tcp transport module. [ 0.470426] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.497315] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.501342] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.501596] audit: initializing netlink subsys (disabled) [ 0.501698] audit: type=2000 audit(0.490:1): initialized [ 0.504702] VFS: Disk quotas dquot_6.5.2 [ 0.504805] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.506472] NFS: Registering the id_resolver key type [ 0.506689] Key type id_resolver registered [ 0.506698] Key type id_legacy registered [ 0.506817] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.509742] bounce: pool size: 64 pages [ 0.509791] io scheduler noop registered [ 0.509804] io scheduler deadline registered [ 0.509833] io scheduler cfq registered (default) [ 0.514386] pinctrl-single 4a002840.pinmux: 219 pins at pa fc002840 size 438 [ 0.514708] pinctrl-single 4ae0c840.pinmux: 28 pins at pa fce0c840 size 56 [ 0.519328] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.523468] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.523485] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.523803] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 306, base_baud = 3000000) is a OMAP UART0 [ 0.524984] omap_uart 4806c000.serial: no wakeirq for uart0 [ 0.524999] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 0.525180] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 307, base_baud = 3000000) is a OMAP UART1 [ 0.525955] omap_uart 48020000.serial: no wakeirq for uart0 [ 0.525969] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48020000[0]' [ 0.526148] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 308, base_baud = 3000000) is a OMAP UART2 [ 0.526887] omap_uart 4806e000.serial: no wakeirq for uart0 [ 0.526901] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 0.527087] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 309, base_baud = 3000000) is a OMAP UART3 [ 1.743388] console [ttyO3] enabled [ 1.747892] omap_uart 48066000.serial: no wakeirq for uart0 [ 1.753724] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48066000[0]' [ 1.763774] 48066000.serial: ttyO4 at MMIO 0x48066000 (irq = 310, base_baud = 3000000) is a OMAP UART4 [ 1.774435] omap_uart 48068000.serial: no wakeirq for uart0 [ 1.780263] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48068000[0]' [ 1.790269] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 311, base_baud = 3000000) is a OMAP UART5 [ 1.818928] brd: module loaded [ 1.834208] loop: module loaded [ 1.839518] ahci 4a140000.sata: forcing PORTS_IMPL to 0x1 [ 1.845261] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.854172] ahci 4a140000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst [ 1.865822] scsi host0: ahci [ 1.869704] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 335 [ 1.878957] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.895142] mousedev: PS/2 mouse device common for all mice [ 1.900971] i2c /dev entries driver [ 1.905935] Driver 'mmcblk' needs updating - please use bus_type methods [ 1.913838] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 1.920131] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.926981] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 1.937299] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 1.942129] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 1.948414] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.955265] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 1.965558] omap_hsmmc 4809c000.mmc: Got WP GPIO [ 1.970733] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 1.977861] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.985425] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 1.991702] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 1.998531] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.008087] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.017546] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.024558] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 2.030658] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 2.036954] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 2.043777] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.053324] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.062784] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.069792] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 2.114580] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.120889] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.127765] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.137341] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.146834] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.153867] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.160010] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.166333] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.173187] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.182775] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.192260] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.199308] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.205724] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.212662] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.220304] ledtrig-cpu: registered to indicate activity on CPUs [ 2.224319] ata1: SATA link down (SStatus 0 SControl 300) [ 2.233687] oprofile: using timer interrupt. [ 2.238521] TCP: cubic registered [ 2.241997] Initializing XFRM netlink socket [ 2.246552] NET: Registered protocol family 17 [ 2.251234] NET: Registered protocol family 15 [ 2.256069] Key type dns_resolver registered [ 2.260650] omap_vc_init_channel: No PMIC info for vdd_core [ 2.266494] omap_vp_init: No PMIC info for vdd_core [ 2.271611] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.277265] omap_vp_init: No PMIC info for vdd_mm [ 2.282193] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.287935] omap_vp_init: No PMIC info for vdd_mpu [ 2.293537] Power Management for TI OMAP4+ devices. [ 2.298872] ThumbEE CPU extension supported. [ 2.303382] Registering SWP/SWPB emulation handler [ 2.303386] mmc0: MAN_BKOPS_EN bit is not set [ 2.313001] SmartReflex Class3 initialized [ 2.318653] mmc0: new high speed MMC card at address 0001 [ 2.325882] mmcblk0: mmc0:0001 SEM08G 7.28 GiB [ 2.332170] mmcblk0boot0: mmc0:0001 SEM08G partition 1 2.00 MiB [ 2.339159] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.349993] mmcblk0boot1: mmc0:0001 SEM08G partition 2 2.00 MiB [ 2.350609] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to find supply vin [ 2.351315] reg-fixed-voltage fixed-regulator-vwlan-pdn: Failed to register regulator: -517 [ 2.351366] platform fixed-regulator-vwlan-pdn: Driver reg-fixed-voltage requests probe deferral [ 2.351714] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.352117] reg-fixed-voltage fixed-regulator-vwlan: Failed to find supply vin [ 2.352519] reg-fixed-voltage fixed-regulator-vwlan: Failed to register regulator: -517 [ 2.352551] platform fixed-regulator-vwlan: Driver reg-fixed-voltage requests probe deferral [ 2.375305] palmas 0-0048: Irq flag is 0x00000000 [ 2.429274] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.481068] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.488575] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz [ 2.495897] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 2.502178] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 2.508496] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.515376] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.525753] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.530595] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 2.536901] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.543759] of_get_named_gpiod_flags: parsed 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' - status (0) [ 2.554086] omap_hsmmc 4809c000.mmc: Got WP GPIO [ 2.605161] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.611495] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.618368] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.627963] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.637487] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.644574] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.650726] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.657072] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.663923] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.673518] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.683024] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.690073] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.696450] omap_hsmmc 480ad000.mmc: unable to get vmmc regulator -517 [ 2.703447] platform 480ad000.mmc: Driver omap_hsmmc requests probe deferral [ 2.711015] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan-pdn[0]' - status (0) [ 2.722203] vwlan_pdn_fixed: supplied by ldo2 [ 2.727268] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixed-regulator-vwlan[0]' - status (0) [ 2.738078] vwlan_fixed: supplied by vwlan_pdn_fixed [ 2.743958] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.750276] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.757141] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.766743] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.766764] mmc1: host does not support reading read-only switch, assuming write-enable [ 2.784651] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.791677] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.791715] mmc1: new high speed SDHC card at address 0002 [ 2.792557] mmcblk1: mmc1:0002 00000 3.66 GiB [ 2.803720] mmcblk1: p1 p2 [ 2.811175] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.817484] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.824340] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.833917] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.843412] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.850439] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.895891] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.902460] sr_init: No PMIC hook to init smartreflex [ 2.907973] sr_init: platform driver register failed for SR [ 2.927844] mmc2: new high speed SDIO card at address 0001 [ 2.943155] ads7846-reg: disabling [ 2.953796] kjournald starting. Commit interval 5 seconds [ 2.953913] EXT3-fs (mmcblk1p2): mounted filesystem with ordered data mode [ 2.953981] VFS: Mounted root (ext3 filesystem) readonly on device 179:26. [ 2.966735] devtmpfs: mounted [ 2.967131] Freeing unused kernel memory: 428K (c0801000 - c086c000) /bin/sh: can't access tty; job control turned off / # / # / #