CCCSending /srv/serial/u-boot-spl.bin, 784 blocks: Give your local XMODEM receive command now. Transfer complete ot SPL 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 163Sending: u-boot.bin Sending: Transfer complete em - CRC mode, 3(SOH)/375(STX)/0(CAN) packets, 2 retries Loaded 384084 bytes U-Boot 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 U-Boot# U-Boot# setenv autoload off; setenv serverip 192.168.57.1; dhcp cpsw Waiting for PHY auto negotiation to complete.. done link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.138 U-Boot# tftp 0x81000000 zImage.omap2plus_defconfig link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'zImage.omap2plus_defconfig'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################################### 971.7 KiB/s done Bytes transferred = 4495776 (4499a0 hex) U-Boot# tftp 0x82000000 am335x-bone.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'am335x-bone.dtb'. Load address: 0x82000000 Loading: *### 843.8 KiB/s done Bytes transferred = 29409 (72e1 hex) U-Boot# setenv bootargs console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp U-Boot# U-Boot# bootz 0x81000000 - 0x82000000 ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 82000000, end 8200a2e0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.0.0-130747-g39a8804 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Tue Apr 21 08:16:21 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c08fb0c0, node_mem_map cfcb1000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 12 pages/cpu @cfc5e000 s18496 r8192 d22464 u49152 [ 0.000000] pcpu-alloc: s18496 r8192 d22464 u49152 alloc=12*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64704 [ 0.000000] Kernel command line: console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 224396K/261120K available (5896K kernel code, 595K rwdata, 2264K rodata, 428K init, 8219K bss, 20340K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0800620 (8162 kB) [ 0.000000] .init : 0xc0801000 - 0xc086c000 ( 428 kB) [ 0.000000] .data : 0xc086c000 - 0xc0900f68 ( 596 kB) [ 0.000000] .bss : 0xc0900f68 - 0xc1107cd0 (8220 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000097] OMAP clocksource: timer1 at 24000000 Hz [ 0.001429] Console: colour dummy device 80x30 [ 0.001517] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001532] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001546] ... MAX_LOCK_DEPTH: 48 [ 0.001559] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001572] ... CLASSHASH_SIZE: 4096 [ 0.001585] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001598] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001610] ... CHAINHASH_SIZE: 32768 [ 0.001623] memory used by lock dependency info: 5167 kB [ 0.001638] per task-struct memory footprint: 1152 bytes [ 0.001675] Calibrating delay loop... 548.04 BogoMIPS (lpj=2740224) [ 0.108231] pid_max: default: 32768 minimum: 301 [ 0.108785] Security Framework initialized [ 0.109056] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.109083] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.113821] Initializing cgroup subsys blkio [ 0.113885] Initializing cgroup subsys memory [ 0.114027] Initializing cgroup subsys devices [ 0.114187] Initializing cgroup subsys freezer [ 0.114390] Initializing cgroup subsys perf_event [ 0.114516] CPU: Testing write buffer coherency: ok [ 0.116622] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.116792] Setting up static identity map for 0x80596588 - 0x805965f8 [ 0.122591] Brought up 1 CPUs [ 0.122624] SMP: Total of 1 processors activated (548.04 BogoMIPS). [ 0.122642] CPU: All CPU(s) started in SVC mode. [ 0.127401] devtmpfs: initialized [ 0.131522] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.194008] omap_hwmod: tptc0 using broken dt data from edma [ 0.194671] omap_hwmod: tptc1 using broken dt data from edma [ 0.195311] omap_hwmod: tptc2 using broken dt data from edma [ 0.206805] omap_hwmod: debugss: _wait_target_disable failed [ 0.269144] pinctrl core: initialized pinctrl subsystem [ 0.322211] NET: Registered protocol family 16 [ 0.332249] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.335482] cpuidle: using governor ladder [ 0.335528] cpuidle: using governor menu [ 0.347128] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.348670] OMAP GPIO hardware version 0.1 [ 0.350811] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.353898] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.356940] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.377154] No ATAGs? [ 0.377200] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.443524] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.444651] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator@0[0]' [ 0.450138] SCSI subsystem initialized [ 0.451270] libata version 3.00 loaded. [ 0.452873] omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe [ 0.452938] platform 44e0b000.i2c: Driver omap_i2c requests probe deferral [ 0.459484] Switched to clocksource timer1 [ 0.683715] NET: Registered protocol family 2 [ 0.686561] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.686827] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.688071] TCP: Hash tables configured (established 2048 bind 2048) [ 0.688366] TCP: reno registered [ 0.688411] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.688755] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.690575] NET: Registered protocol family 1 [ 0.692932] RPC: Registered named UNIX socket transport module. [ 0.692965] RPC: Registered udp transport module. [ 0.692983] RPC: Registered tcp transport module. [ 0.692999] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.695952] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.702885] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.703301] audit: initializing netlink subsys (disabled) [ 0.703683] audit: type=2000 audit(0.700:1): initialized [ 0.710981] VFS: Disk quotas dquot_6.5.2 [ 0.711229] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.714849] NFS: Registering the id_resolver key type [ 0.715428] Key type id_resolver registered [ 0.715451] Key type id_legacy registered [ 0.715734] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.723061] io scheduler noop registered [ 0.723111] io scheduler deadline registered [ 0.723192] io scheduler cfq registered (default) [ 0.726056] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.729883] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.739043] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.739101] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@44e09000[0]' [ 0.740276] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 154, base_baud = 3000000) is a OMAP UART0 [ 1.508558] console [ttyO0] enabled [ 1.559065] brd: module loaded [ 1.590724] loop: module loaded [ 1.597633] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.612692] mousedev: PS/2 mouse device common for all mice [ 1.618579] i2c /dev entries driver [ 1.622803] Driver 'mmcblk' needs updating - please use bus_type methods [ 1.631581] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 1.637899] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.644896] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.655397] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.660318] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 1.666622] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.673522] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 1.683146] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 1.692673] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 1.699937] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 1.707413] omap_hsmmc 48060000.mmc: unable to get vmmc regulator -517 [ 1.715338] platform 48060000.mmc: Driver omap_hsmmc requests probe deferral [ 1.723233] ledtrig-cpu: registered to indicate activity on CPUs [ 1.731388] oprofile: using arm/armv7 [ 1.736258] TCP: cubic registered [ 1.739930] Initializing XFRM netlink socket [ 1.744627] NET: Registered protocol family 17 [ 1.749489] NET: Registered protocol family 15 [ 1.754725] Key type dns_resolver registered [ 1.759689] omap_voltage_late_init: Voltage driver support not added [ 1.766378] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize [ 1.774929] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize [ 1.785056] ThumbEE CPU extension supported. [ 1.789702] Registering SWP/SWPB emulation handler [ 1.794761] SmartReflex Class3 initialized [ 1.852340] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 1.858066] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 1.865494] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 1.871913] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.878820] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.889403] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.894269] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 1.900614] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.907470] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 1.917089] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 1.926612] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 1.933698] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 2.049403] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.055829] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.067913] libphy: 4a101000.mdio: probed [ 2.072327] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.084209] cpsw 4a100000.ethernet: Detected MACID = 78:c5:e5:c3:1e:2a [ 2.095339] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.102072] sr_init: No PMIC hook to init smartreflex [ 2.107758] sr_init: platform driver register failed for SR [ 2.146372] net eth0: initializing cpsw version 1.12 (0) [ 2.154907] net eth0: phy found : id is : 0x7c0f1 [ 2.160103] libphy: PHY 4a101000.mdio:01 not found [ 2.165140] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 5.230061] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 5.249347] Sending DHCP requests ., OK [ 5.269913] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.138 [ 5.278908] IP-Config: Complete: [ 5.282433] device=eth0, hwaddr=78:c5:e5:c3:1e:2a, ipaddr=192.168.57.138, mask=255.255.255.0, gw=255.255.255.255 [ 5.293603] host=192.168.57.138, domain=example.org, nis-domain=(none) [ 5.300942] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.307695] nameserver0=192.168.57.1 [ 5.312405] vmmcsd_fixed: disabling [ 5.345374] VFS: Mounted root (nfs filesystem) on device 0:14. [ 5.354419] devtmpfs: mounted [ 5.358714] Freeing unused kernel memory: 428K (c0801000 - c086c000) INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.284749] udevd[142]: starting version 175 [ ok . [....] Synthesizing the initial hotplug events...udevd[183]: error changing net interface name eth0 to eth4: Device or resource busy [ ok done. [....] Waiting for /dev to be fully populated...[ ok done. [ 15.207637] random: nonblocking pool is initialized [....] Activating swap...[ ok done. [....] Cleaning up temporary files... /tmp[ ok . [....] Activating lvm and md swap...[ ok done. [....] Checking file systems...fsck from util-linux 2.20.1 [ ok done. [....] Mounting local filesystems...[ ok done. [....] Activating swapfile swap...[ ok done. [....] Cleaning up temporary files...[ ok . [....] Setting kernel variables ...[ ok done. [....] Configuring network interfaces...[ ok done. [....] Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 [ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [....] Cleaning up temporary files...[ ok . [....] Starting network benchmark server[ ok . INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting system message bus: dbus[ ok . [....] Starting network benchmark server[FAIL failed! [....] Starting NFS common utilities: statd idmapd[ ok . [....] Starting rpcbind daemon...[....] Already running.[ ok . Debian GNU/Linux wheezy/sid armel ttyO0 armel login: