U-Boot 1.1.4 (Mar 18 2007 - 12:22:00) OMAP2430C-GP revision 3, PRCM #5A TI 2430SDP 1.1 Version + mDDR (Boot NOR) DRAM: 128 MB Flash: 192 MB NAND:64 MB In: serial Out: serial Err: serial Hit any key to stop autoboot: 3  0 OMAP243X SDP # OMAP243X SDP # setenv bootargs console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh OMAP243X SDP # loady ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... CSending: uImage-dtb.omap2430-sdp Sending: Transfer complete m - CRC mode, 3(SOH)/3391(STX)/0(CAN) packets, 3 retries ## Total Size = 0x0034fc27 = 3472423 Bytes OMAP243X SDP # bootm ## Booting image at 80000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3472359 Bytes = 3.3 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... %% Start PM consolidated quick test (retention only) %% Preparation [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.1.0-rc2-12071-g5ebe6af (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Tue May 5 23:34:52 MDT 2015 [ 0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP2430 SDP [ 0.000000] earlycon: no match for ttyO0,115200n8 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x86800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 32512 [ 0.000000] free_area_init_node: node 0, pgdat c09585c0, node_mem_map c7dd1000 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP2430 [ 0.000000] [ 0.000000] PERCPU: Embedded 13 pages/cpu @c7d6e000 s22976 r8192 d22080 u53248 [ 0.000000] pcpu-alloc: s22976 r8192 d22080 u53248 alloc=13*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32224 [ 0.000000] Kernel command line: console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 94112K/130048K available (6211K kernel code, 739K rwdata, 2168K rodata, 440K init, 8220K bss, 19552K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0837090 (8381 kB) [ 0.000000] .init : 0xc0838000 - 0xc08a6000 ( 440 kB) [ 0.000000] .data : 0xc08a6000 - 0xc095ec18 ( 740 kB) [ 0.000000] .bss : 0xc0961000 - 0xc11683d0 (8221 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] clocksource 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.000061] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000640] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.003387] Console: colour dummy device 80x30 [ 0.003570] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.003601] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.003631] ... MAX_LOCK_DEPTH: 48 [ 0.003662] ... MAX_LOCKDEP_KEYS: 8191 [ 0.003692] ... CLASSHASH_SIZE: 4096 [ 0.003723] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.003753] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.003784] ... CHAINHASH_SIZE: 32768 [ 0.003814] memory used by lock dependency info: 5167 kB [ 0.003845] per task-struct memory footprint: 1152 bytes [ 0.003906] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816) [ 0.114562] pid_max: default: 32768 minimum: 301 [ 0.115814] Security Framework initialized [ 0.116394] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.116485] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.129089] Initializing cgroup subsys blkio [ 0.129211] Initializing cgroup subsys memory [ 0.129486] Initializing cgroup subsys devices [ 0.129821] Initializing cgroup subsys freezer [ 0.130371] Initializing cgroup subsys perf_event [ 0.130615] CPU: Testing write buffer coherency: ok [ 0.136657] missing device node for CPU 0 [ 0.136718] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366 [ 0.136993] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.154357] Brought up 1 CPUs [ 0.154663] SMP: Total of 1 processors activated (262.96 BogoMIPS). [ 0.154693] CPU: All CPU(s) started in SVC mode. [ 0.169067] devtmpfs: initialized [ 0.199371] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 0.325988] omap_hwmod: usb_otg_hs: _wait_target_ready failed: -16 [ 0.326049] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3) [ 0.348663] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.356903] pinctrl core: initialized pinctrl subsystem [ 0.548858] NET: Registered protocol family 16 [ 0.573913] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.581848] cpuidle: using governor ladder [ 0.581939] cpuidle: using governor menu [ 0.658996] omap_gpio 4900c000.gpio: Could not get gpio dbck [ 0.662658] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.666839] OMAP GPIO hardware version 2.4 [ 0.669982] omap_gpio 4900e000.gpio: Could not get gpio dbck [ 0.671722] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.677764] omap_gpio 49010000.gpio: Could not get gpio dbck [ 0.679016] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.685058] omap_gpio 49012000.gpio: Could not get gpio dbck [ 0.686340] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.692230] omap_gpio 480b6000.gpio: Could not get gpio dbck [ 0.693969] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.700286] omap-gpmc 6e000000.gpmc: GPMC revision 3.0 [ 0.718414] No ATAGs? [ 0.718597] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.718658] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.727294] OMAP DMA hardware revision 4.0 [ 0.954162] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.968536] SCSI subsystem initialized [ 0.970794] libata version 3.00 loaded. [ 0.981536] omap_i2c 48070000.i2c: bus 0 rev3.3 at 100 kHz [ 0.987823] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz [ 1.006103] Switched to clocksource 32k_counter [ 1.621063] NET: Registered protocol family 2 [ 1.628723] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.629272] TCP bind hash table entries: 1024 (order: 3, 36864 bytes) [ 1.630645] TCP: Hash tables configured (established 1024 bind 1024) [ 1.631378] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.632171] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.636230] NET: Registered protocol family 1 [ 1.642852] RPC: Registered named UNIX socket transport module. [ 1.642944] RPC: Registered udp transport module. [ 1.642974] RPC: Registered tcp transport module. [ 1.643005] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.649749] CPU PMU: Failed to parse /interrupt-affinity[0] [ 1.650024] hw perfevents: enabled with armv6_1136 PMU driver, 3 counters available [ 1.670745] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.671569] audit: initializing netlink subsys (disabled) [ 1.672424] audit: type=2000 audit(1.660:1): initialized [ 1.690185] VFS: Disk quotas dquot_6.6.0 [ 1.690673] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.701873] NFS: Registering the id_resolver key type [ 1.703735] Key type id_resolver registered [ 1.703796] Key type id_legacy registered [ 1.704528] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.728546] io scheduler noop registered [ 1.728637] io scheduler deadline registered [ 1.728790] io scheduler cfq registered (default) [ 1.738433] pinctrl-single 49002030.pinmux: 340 pins at pa fb002030 size 340 [ 1.747924] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.772705] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.772796] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 1.774810] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 2.641815] console [ttyO0] enabled [ 2.654479] omap_uart 4806c000.serial: no wakeirq for uart1 [ 2.660705] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 2.671722] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 2.686584] omap_uart 4806e000.serial: no wakeirq for uart2 [ 2.692535] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 2.703552] 4806e000.serial: ttyO2 at MMIO 0x4806e000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 2.833404] brd: module loaded [ 2.908752] loop: module loaded [ 2.957702] twl 1-0048: PIH (irq 23) chaining IRQs 274..282 [ 2.964996] twl 1-0048: power (irq 279) chaining IRQs 282..289 [ 3.160278] twl4030_gpio twl4030-gpio: gpio (irq 274) chaining IRQs 290..307 [ 3.170349] gpiochip_find_base: found new base at 494 [ 3.178070] gpiochip_add: registered GPIOs 494 to 511 on device: twl4030 [ 3.210296] mtdoops: mtd device (mtddev=name/number) must be supplied [ 3.243164] smc91x 8000300.ethernet: GPIO lookup for consumer power [ 3.249969] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.257019] of_get_named_gpiod_flags: can't parse 'power-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.268463] of_get_named_gpiod_flags: can't parse 'power-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.279754] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.287506] smc91x 8000300.ethernet: lookup for GPIO power failed [ 3.293975] smc91x 8000300.ethernet: GPIO lookup for consumer reset [ 3.300750] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.307800] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.319213] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.330505] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.337738] smc91x 8000300.ethernet: lookup for GPIO reset failed [ 3.344360] smc91x 8000300.ethernet (unnamed net_device) (uninitialized): smc91x: IOADDR c890a300 doesn't match configuration (0). [ 3.356933] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre [ 3.373199] smc91x 8000300.ethernet eth0: SMC91C94 (rev 9) at c890a300 IRQ 261 [ 3.381011] [ 3.382659] smc91x 8000300.ethernet eth0: Ethernet addr: 10:03:31:33:16:8f [ 3.404541] mousedev: PS/2 mouse device common for all mice [ 3.410736] i2c /dev entries driver [ 3.428771] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 3.435150] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 3.442260] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.452056] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 3.461700] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 3.468933] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 3.475128] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 3.481597] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 3.488616] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.498382] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 3.508056] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 3.515167] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 3.577453] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 3.583831] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.590942] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.600738] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.610412] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.617614] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 3.623809] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 3.630279] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.637298] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.647033] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.656707] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.663818] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 3.671203] 480b4000.mmc supply vmmc not found, using dummy regulator [ 3.678955] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.687499] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.727081] ledtrig-cpu: registered to indicate activity on CPUs [ 3.738281] oprofile: using arm/armv6 [ 3.745208] Initializing XFRM netlink socket [ 3.750579] NET: Registered protocol family 17 [ 3.755706] NET: Registered protocol family 15 [ 3.761993] Key type dns_resolver registered [ 3.767211] SmartReflex Class3 initialized [ 3.806640] hctosys: unable to open rtc device (rtc0) [ 3.812042] sr_init: No PMIC hook to init smartreflex [ 3.818542] sr_init: platform driver register failed for SR [ 3.960235] VUSB3V1: disabling [ 3.967163] VUSB1V8: disabling [ 3.973754] VUSB1V5: disabling [ 3.999084] Waiting for root device /dev/mmcblk0p1...