U-Boot 1.1.4 (Mar 18 2007 - 12:22:00) OMAP2430C-GP revision 3, PRCM #5A TI 2430SDP 1.1 Version + mDDR (Boot NOR) DRAM: 128 MB Flash: 192 MB NAND:64 MB In: serial Out: serial Err: serial Hit any key to stop autoboot: 3  0 OMAP243X SDP # OMAP243X SDP # setenv bootargs console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh OMAP243X SDP # loady ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... CSending: uImage-dtb.omap2430-sdp Sending: Transfer complete dem - CRC mode, 2(SOH)/3395(STX)/0(CAN) packets, 3 retries ## Total Size = 0x00350bbf = 3476415 Bytes OMAP243X SDP # bootm ## Booting image at 80000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3476351 Bytes = 3.3 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... %% Start PM consolidated quick test (retention only) %% Preparation [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.1.0-143712-gb953c0d (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Fri Jun 26 17:06:43 MDT 2015 [ 0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP2430 SDP [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x86800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 32512 [ 0.000000] free_area_init_node: node 0, pgdat c095a780, node_mem_map c7dd1000 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32512 pages, LIFO batch:7 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP2430 [ 0.000000] [ 0.000000] PERCPU: Embedded 13 pages/cpu @c7d6e000 s22976 r8192 d22080 u53248 [ 0.000000] pcpu-alloc: s22976 r8192 d22080 u53248 alloc=13*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32224 [ 0.000000] Kernel command line: console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 94104K/130048K available (6215K kernel code, 739K rwdata, 2172K rodata, 440K init, 8220K bss, 19560K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08390b4 (8389 kB) [ 0.000000] .init : 0xc083a000 - 0xc08a8000 ( 440 kB) [ 0.000000] .data : 0xc08a8000 - 0xc0960dc0 ( 740 kB) [ 0.000000] .bss : 0xc0963000 - 0xc116a350 (8221 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] clocksource 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.000061] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000610] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.003326] Console: colour dummy device 80x30 [ 0.003540] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.003570] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.003601] ... MAX_LOCK_DEPTH: 48 [ 0.003631] ... MAX_LOCKDEP_KEYS: 8191 [ 0.003662] ... CLASSHASH_SIZE: 4096 [ 0.003692] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.003723] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.003753] ... CHAINHASH_SIZE: 32768 [ 0.003784] memory used by lock dependency info: 5167 kB [ 0.003814] per task-struct memory footprint: 1152 bytes [ 0.003875] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816) [ 0.114624] pid_max: default: 32768 minimum: 301 [ 0.115875] Security Framework initialized [ 0.116455] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.116516] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.129089] Initializing cgroup subsys blkio [ 0.129211] Initializing cgroup subsys memory [ 0.129455] Initializing cgroup subsys devices [ 0.129821] Initializing cgroup subsys freezer [ 0.130371] Initializing cgroup subsys perf_event [ 0.130615] CPU: Testing write buffer coherency: ok [ 0.136566] missing device node for CPU 0 [ 0.136627] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366 [ 0.136901] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.154266] Brought up 1 CPUs [ 0.154327] SMP: Total of 1 processors activated (262.96 BogoMIPS). [ 0.154357] CPU: All CPU(s) started in SVC mode. [ 0.168945] devtmpfs: initialized [ 0.365692] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 0.490478] omap_hwmod: usb_otg_hs: _wait_target_ready failed: -16 [ 0.490539] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3) [ 0.513366] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.521759] pinctrl core: initialized pinctrl subsystem [ 0.542633] NET: Registered protocol family 16 [ 0.568115] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.576293] cpuidle: using governor ladder [ 0.576416] cpuidle: using governor menu [ 0.652740] omap_gpio 4900c000.gpio: Could not get gpio dbck [ 0.656646] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.660491] OMAP GPIO hardware version 2.4 [ 0.663848] omap_gpio 4900e000.gpio: Could not get gpio dbck [ 0.665374] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.671051] omap_gpio 49010000.gpio: Could not get gpio dbck [ 0.672302] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.678314] omap_gpio 49012000.gpio: Could not get gpio dbck [ 0.679565] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.685729] omap_gpio 480b6000.gpio: Could not get gpio dbck [ 0.687072] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.693298] omap-gpmc 6e000000.gpmc: GPMC revision 3.0 [ 0.711303] No ATAGs? [ 0.711517] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.711547] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.720184] OMAP DMA hardware revision 4.0 [ 0.941162] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.955841] SCSI subsystem initialized [ 0.958099] libata version 3.00 loaded. [ 0.968627] omap_i2c 48070000.i2c: bus 0 rev3.3 at 100 kHz [ 0.974914] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz [ 0.992889] Switched to clocksource 32k_counter [ 1.616882] NET: Registered protocol family 2 [ 1.624572] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.625122] TCP bind hash table entries: 1024 (order: 3, 36864 bytes) [ 1.626525] TCP: Hash tables configured (established 1024 bind 1024) [ 1.627288] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.628082] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.631866] NET: Registered protocol family 1 [ 1.638732] RPC: Registered named UNIX socket transport module. [ 1.638793] RPC: Registered udp transport module. [ 1.638824] RPC: Registered tcp transport module. [ 1.638854] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.645538] CPU PMU: Failed to parse /pmu/interrupt-affinity[0] [ 1.645782] hw perfevents: enabled with armv6_1136 PMU driver, 3 counters available [ 1.666351] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.667175] audit: initializing netlink subsys (disabled) [ 1.667999] audit: type=2000 audit(1.650:1): initialized [ 1.685729] VFS: Disk quotas dquot_6.6.0 [ 1.686248] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.697174] NFS: Registering the id_resolver key type [ 1.699035] Key type id_resolver registered [ 1.699096] Key type id_legacy registered [ 1.699859] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.721832] io scheduler noop registered [ 1.722229] io scheduler deadline registered [ 1.722412] io scheduler cfq registered (default) [ 1.731719] pinctrl-single 49002030.pinmux: 340 pins at pa fb002030 size 340 [ 1.741271] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.766448] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.766540] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 1.768493] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 2.626770] console [ttyO0] enabled [ 2.639465] omap_uart 4806c000.serial: no wakeirq for uart1 [ 2.645660] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 2.656616] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 2.671203] omap_uart 4806e000.serial: no wakeirq for uart2 [ 2.677398] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 2.688354] 4806e000.serial: ttyO2 at MMIO 0x4806e000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 2.817382] brd: module loaded [ 2.891693] loop: module loaded [ 2.940734] twl 1-0048: PIH (irq 23) chaining IRQs 274..282 [ 2.948150] twl 1-0048: power (irq 279) chaining IRQs 282..289 [ 3.144012] twl4030_gpio twl4030-gpio: gpio (irq 274) chaining IRQs 290..307 [ 3.153778] gpiochip_find_base: found new base at 494 [ 3.161254] gpiochip_add: registered GPIOs 494 to 511 on device: twl4030 [ 3.193420] mtdoops: mtd device (mtddev=name/number) must be supplied [ 3.225830] smc91x 8000300.ethernet: GPIO lookup for consumer power [ 3.232666] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.239562] of_get_named_gpiod_flags: can't parse 'power-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.250946] of_get_named_gpiod_flags: can't parse 'power-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.262207] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.269836] smc91x 8000300.ethernet: lookup for GPIO power failed [ 3.276428] smc91x 8000300.ethernet: GPIO lookup for consumer reset [ 3.283142] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.290069] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.301422] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.312713] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.319793] smc91x 8000300.ethernet: lookup for GPIO reset failed [ 3.326721] smc91x 8000300.ethernet (unnamed net_device) (uninitialized): smc91x: IOADDR c890a300 doesn't match configuration (0). [ 3.339233] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre [ 3.355468] smc91x 8000300.ethernet eth0: SMC91C94 (rev 9) at c890a300 IRQ 261 [ 3.363250] [ 3.364868] smc91x 8000300.ethernet eth0: Ethernet addr: 10:03:31:33:16:8f [ 3.386688] mousedev: PS/2 mouse device common for all mice [ 3.392852] i2c /dev entries driver [ 3.410552] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 3.417205] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 3.424224] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.433959] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 3.443572] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 3.450683] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 3.456939] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 3.463378] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 3.470275] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.480010] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 3.489624] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 3.496795] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 3.554046] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 3.560424] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.567504] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.577239] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.586853] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.594024] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 3.600219] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 3.606658] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.613647] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.623382] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.632995] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.640075] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 3.647430] 480b4000.mmc supply vmmc not found, using dummy regulator [ 3.655456] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.663848] omap_hsmmc 480b4000.mmc: could not set regulator OCR (-22) [ 3.703704] ledtrig-cpu: registered to indicate activity on CPUs [ 3.714843] oprofile: using arm/armv6 [ 3.721771] Initializing XFRM netlink socket [ 3.727111] NET: Registered protocol family 17 [ 3.732330] NET: Registered protocol family 15 [ 3.738555] Key type dns_resolver registered [ 3.743774] SmartReflex Class3 initialized [ 3.783355] hctosys: unable to open rtc device (rtc0) [ 3.788726] sr_init: No PMIC hook to init smartreflex [ 3.795196] sr_init: platform driver register failed for SR [ 3.940612] VUSB3V1: disabling [ 3.947540] VUSB1V8: disabling [ 3.954498] VUSB1V5: disabling [ 3.979797] Waiting for root device /dev/mmcblk0p1...