Texas Instruments X-Loader 1.47 (Jan 14 2011 - 15:43:28) Starting X-loader on MMC Reading boot sector 212836 Bytes Read from MMC Starting OS Bootloader from MMC... Starting OS Bootloader... U-Boot 2010.06 (Jan 14 2011 - 15:43:45) OMAP34xx/35xx-GP ES2.1, CPU-OPP2 L3-165MHz OMAP3 EVM board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 512 MiB In: serial Out: serial Err: serial Read back SMSC id 0x92200000 Die ID #368000229ff80000016071640902c013 Net: smc911x-0 Hit any key to stop autoboot: 3  0 OMAP3_EVM # OMAP3_EVM # setenv bootfile uImage-dtb.omap3-evm-37xx OMAP3_EVM # OMAP3_EVM # dhcp smc911x: detected LAN9220 controller smc911x: phy initialized smc911x: MAC 00:50:c2:7e:99:42 BOOTP broadcast 1 DHCP client bound to address 192.168.57.131 Using smc911x-0 device TFTP from server 192.168.57.1; our IP address is 192.168.57.131 Filename 'uImage-dtb.omap3-evm-37xx'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################### done Bytes transferred = 3533311 (35e9ff hex) OMAP3_EVM # setenv bootargs console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh OMAP3_EVM # OMAP3_EVM # bootm ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3533247 Bytes = 3.4 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.2.0-rc5-157887-g74d3329 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Sun Aug 9 20:09:02 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP37XX EVM (TMDSEVM3730) [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65280 [ 0.000000] free_area_init_node: node 0, pgdat c0970240, node_mem_map cfcb1000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65280 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] PERCPU: Embedded 13 pages/cpu @cfc38000 s20672 r8192 d24384 u53248 [ 0.000000] pcpu-alloc: s20672 r8192 d24384 u53248 alloc=13*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64704 [ 0.000000] Kernel command line: console=ttyO0,115200n8 debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp init=/bin/sh [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 223720K/261120K available (6297K kernel code, 738K rwdata, 2188K rodata, 432K init, 8225K bss, 21016K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0851848 (8487 kB) [ 0.000000] .init : 0xc0852000 - 0xc08be000 ( 432 kB) [ 0.000000] .data : 0xc08be000 - 0xc09768e0 ( 739 kB) [ 0.000000] .bss : 0xc0979000 - 0xc11816d0 (8226 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001251] Console: colour dummy device 80x30 [ 0.001312] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001342] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001342] ... MAX_LOCK_DEPTH: 48 [ 0.001373] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001373] ... CLASSHASH_SIZE: 4096 [ 0.001373] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001403] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001403] ... CHAINHASH_SIZE: 32768 [ 0.001434] memory used by lock dependency info: 5167 kB [ 0.001434] per task-struct memory footprint: 1536 bytes [ 0.001464] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696) [ 0.107330] pid_max: default: 32768 minimum: 301 [ 0.107879] Security Framework initialized [ 0.108062] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.108093] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.112518] Initializing cgroup subsys blkio [ 0.112640] Initializing cgroup subsys memory [ 0.112792] Initializing cgroup subsys devices [ 0.112915] Initializing cgroup subsys freezer [ 0.113098] Initializing cgroup subsys perf_event [ 0.113189] CPU: Testing write buffer coherency: ok [ 0.115173] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.115325] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.122161] Brought up 1 CPUs [ 0.122192] SMP: Total of 1 processors activated (594.73 BogoMIPS). [ 0.122222] CPU: All CPU(s) started in SVC mode. [ 0.126892] devtmpfs: initialized [ 0.243408] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.331176] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp [ 0.333648] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp [ 0.444702] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.448120] pinctrl core: initialized pinctrl subsystem [ 0.455444] NET: Registered protocol family 16 [ 0.464599] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.467895] cpuidle: using governor ladder [ 0.467926] cpuidle: using governor menu [ 0.468719] Reprogramming SDRC clock to 400000000 Hz [ 0.483703] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.485198] OMAP GPIO hardware version 2.5 [ 0.487426] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.490386] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.493316] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.496276] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.499359] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.501037] irq: no irq domain found for /ocp/l4@48000000/scm@2000/pinmux@30 ! [ 0.502014] irq: no irq domain found for /ocp/l4@48000000/scm@2000/pinmux@30 ! [ 0.502929] irq: no irq domain found for /ocp/l4@48000000/scm@2000/pinmux@30 ! [ 0.511840] irq: no irq domain found for /ocp/l4@48000000/scm@2000/pinmux@30 ! [ 0.530303] omap-gpmc 6e000000.gpmc: GPMC revision 5.0 [ 0.530578] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.535461] platform 48058000.ssi-controller: Cannot lookup hwmod 'ssi' [ 0.545898] No ATAGs? [ 0.545928] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.550415] OMAP DMA hardware revision 5.0 [ 0.603942] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.605224] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vddvario[0]' [ 0.606628] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/regulator-vdd33a[0]' [ 0.607818] reg-fixed-voltage wl12xx_vmmc: could not find pctldev for node /ocp/l4@48000000/scm@2000/pinmux@30/pinmux_wl12xx_gpio, deferring probe [ 0.608184] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regulator-lcd-3v3[0]' - status (0) [ 0.615203] SCSI subsystem initialized [ 0.616241] libata version 3.00 loaded. [ 0.621368] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz [ 0.623535] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz [ 0.625793] omap_i2c 48060000.i2c: bus 2 rev4.4 at 400 kHz [ 0.632934] clocksource: Switched to clocksource 32k_counter [ 0.872344] NET: Registered protocol family 2 [ 0.875518] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.875640] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.876770] TCP: Hash tables configured (established 2048 bind 2048) [ 0.877105] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.877441] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.878906] NET: Registered protocol family 1 [ 0.881408] RPC: Registered named UNIX socket transport module. [ 0.881439] RPC: Registered udp transport module. [ 0.881469] RPC: Registered tcp transport module. [ 0.881469] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.887817] hw perfevents: Failed to parse /pmu/interrupt-affinity[0] [ 0.887969] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.896575] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.896942] audit: initializing netlink subsys (disabled) [ 0.897277] audit: type=2000 audit(0.880:1): initialized [ 0.903808] VFS: Disk quotas dquot_6.6.0 [ 0.903991] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.907989] NFS: Registering the id_resolver key type [ 0.908569] Key type id_resolver registered [ 0.908599] Key type id_legacy registered [ 0.908874] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.916107] io scheduler noop registered [ 0.916168] io scheduler deadline registered [ 0.916229] io scheduler cfq registered (default) [ 0.919799] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568 [ 0.920593] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92 [ 0.921813] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size 92 [ 0.929626] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.939849] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.940643] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 1.865600] console [ttyO0] enabled [ 1.872528] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 1.883056] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 1.895385] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@49020000[0]' [ 1.905822] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 1.917877] omap_uart 49042000.serial: no wakeirq for uart3 [ 1.923858] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@49042000[0]' [ 1.934173] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3 [ 1.989807] brd: module loaded [ 2.019927] loop: module loaded [ 2.053070] twl 0-0048: PIH (irq 23) chaining IRQs 341..349 [ 2.059478] twl 0-0048: power (irq 346) chaining IRQs 349..356 [ 2.132080] twl4030_gpio twl4030-gpio: gpio (irq 341) chaining IRQs 357..374 [ 2.140197] gpiochip_find_base: found new base at 492 [ 2.146301] gpiochip_add: registered GPIOs 492 to 511 on device: twl4030 [ 2.234069] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.243469] nand: Could not find valid ONFI parameter page; aborting [ 2.250213] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xbc [ 2.256958] nand: Hynix NAND 512MiB 1,8V 16-bit [ 2.261718] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.269683] nand: using OMAP_ECC_BCH8_CODE_HW_DETECTION_SW [ 2.278320] 5 ofpart partitions found on MTD device omap2-nand.0 [ 2.284729] Creating 5 MTD partitions on "omap2-nand.0": [ 2.290344] 0x000000000000-0x000000080000 : "X-Loader" [ 2.304595] 0x000000080000-0x000000240000 : "U-Boot" [ 2.316223] 0x000000240000-0x000000280000 : "Environment" [ 2.327545] 0x000000280000-0x000000780000 : "Kernel" [ 2.341857] 0x000000780000-0x000020000000 : "Filesystem" [ 2.815338] libphy: smsc911x-mdio: probed [ 2.820129] smsc911x 2c000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=2c000000.etherne:01, irq=-1) [ 2.832550] smsc911x 2c000000.ethernet eth0: MAC Address: 00:50:c2:7e:99:42 [ 2.845825] mousedev: PS/2 mouse device common for all mice [ 2.851715] i2c /dev entries driver [ 2.861968] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 2.868530] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.875457] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.885101] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 2.894622] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 2.901885] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 2.908081] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 2.914459] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.921325] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.930938] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 2.940490] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 2.947570] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 3.003631] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 3.009979] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.016937] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.026580] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.036132] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.043243] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 3.050292] omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 [ 3.060272] ledtrig-cpu: registered to indicate activity on CPUs [ 3.068908] oprofile: using arm/armv7 [ 3.073913] Initializing XFRM netlink socket [ 3.078613] NET: Registered protocol family 17 [ 3.083496] NET: Registered protocol family 15 [ 3.088775] Key type dns_resolver registered [ 3.093749] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iva [ 3.101348] omap2_set_init_voltage: unable to set vdd_mpu_iva [ 3.107513] omap2_set_init_voltage: unable to find boot up OPP for vdd_core [ 3.114868] omap2_set_init_voltage: unable to set vdd_core [ 3.126098] ThumbEE CPU extension supported. [ 3.130645] Registering SWP/SWPB emulation handler [ 3.135803] SmartReflex Class3 initialized [ 3.155792] of_get_named_gpiod_flags: parsed 'gpio' property of node '/wl12xx_vmmc[0]' - status (0) [ 3.168365] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 3.174774] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.181671] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.191314] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.200866] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.207946] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 3.215148] vwl1271: supplied by VMMC2 [ 3.347106] hctosys: unable to open rtc device (rtc0) [ 3.352447] sr_init: No PMIC hook to init smartreflex [ 3.358489] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 3.367675] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 3.466522] smsc911x 2c000000.ethernet eth0: SMSC911x/921x identified at 0xd090e000, IRQ: 288 [ 3.506835] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.515716] mmc0: new SDHC card at address e624 [ 3.523986] mmcblk0: mmc0:e624 SD08G 7.40 GiB [ 3.545989] mmcblk0: p1 p2 p3 [ 3.562194] omap_hsmmc 480b4000.mmc: card claims to support voltages below defined range [ 3.589813] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 3.601287] mmc1: new SDIO card at address 0001 [ 5.832946] Sending DHCP requests ., OK [ 5.963439] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.131 [ 5.972595] IP-Config: Complete: [ 5.976135] device=eth0, hwaddr=00:50:c2:7e:99:42, ipaddr=192.168.57.131, mask=255.255.255.0, gw=255.255.255.255 [ 5.987365] host=192.168.57.131, domain=example.org, nis-domain=(none) [ 5.994720] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 6.001495] nameserver0=192.168.57.1 [ 6.006378] vwl1271: disabling [ 6.010986] VUSB3V1: disabling [ 6.017608] lcd_3v3: disabling [ 6.069458] VFS: Mounted root (nfs filesystem) readonly on device 0:15. [ 6.079254] devtmpfs: mounted [ 6.083709] Freeing unused kernel memory: 432K (c0852000 - c08be000) /bin/sh: 0: can't access tty; job control turned off #