怘€æ€˜€`3f<€fÀæøÀ̆ž?`??f?æžf<øž`??ð3ž<3ž<`<f<?˜à?Ì?Ã03††àÀÌà˜øÃÀÀ˜ø˜ž˜àÃóÀ˜àóÃ̘˜˜03à3f<<`<†žøž~<æžþž`?˜øfÃæàóæž?怘€à˜þž<`<†žøž~<˜æfÏàæžþž`?ø†<†žøž†øæžæž˜žfÏæàfü

U-Boot 2011.06-dirty (Sep 04 2012 - 17:06:58)

OMAP3530-GP ES3.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C:   ready
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
In:    serial
Out:   serial
Err:   serial
Beagle Rev C1/C2/C3
timed out in wait_for_pin: I2C_STAT=0
I2C read: I/O error
Unrecognized expansion board: 0
Die ID #5cf200030000000004013f7902012010
Hit any key to stop autoboot:  2  0 
OMAP3 beagleboard.org # 
OMAP3 beagleboard.org # loady 0x81000000
## Ready for binary (ymodem) download to 0x81000000 at 230400 bps...
CSending: uImage-dtb.omap3-beagle
Sending: 

Transfer complete
xyzModem - CRC mode, 8(SOH)/3447(STX)/0(CAN) packets, 3 retries
## Total Size      = 0x0035def9 = 3530489 Bytes
OMAP3 beagleboard.org # 
OMAP3 beagleboard.org # 
OMAP3 beagleboard.org # setenv bootargs console=ttyO2,230400n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait earlyprintk
OMAP3 beagleboard.org # 
OMAP3 beagleboard.org # bootm 0x81000000
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   Linux-
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3530425 Bytes = 3.4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.2.0-158462-g64291f7 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Sun Sep 13 14:54:25 MDT 2015
[    0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine model: TI OMAP3 BeagleBoard
[    0.000000] cma: Reserved 16 MiB at 0x8e800000
[    0.000000] Memory policy: Data cache writeback
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp )
[    0.000000] PERCPU: Embedded 13 pages/cpu @cfc38000 s20672 r8192 d24384 u53248
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64704
[    0.000000] Kernel command line: console=ttyO2,230400n8 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait earlyprintk
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 223712K/261120K available (6297K kernel code, 738K rwdata, 2192K rodata, 436K init, 8225K bss, 21024K reserved, 16384K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc085285c   (8491 kB)
[    0.000000]       .init : 0xc0853000 - 0xc08c0000   ( 436 kB)
[    0.000000]       .data : 0xc08c0000 - 0xc09788a0   ( 739 kB)
[    0.000000]        .bss : 0xc097b000 - 0xc11836d0   (8226 kB)
[    0.000000] Running RCU self tests
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU lockdep checking is enabled.
[    0.000000] 	Additional per-CPU info printed with stalls.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[    0.000000] OMAP clockevent source: timer12 at 32768 Hz
[    0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns
[    0.000030] OMAP clocksource: 32k_counter at 32768 Hz
[    0.001678] Console: colour dummy device 80x30
[    0.001800] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.001800] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.001831] ... MAX_LOCK_DEPTH:          48
[    0.001831] ... MAX_LOCKDEP_KEYS:        8191
[    0.001861] ... CLASSHASH_SIZE:          4096
[    0.001861] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.001892] ... MAX_LOCKDEP_CHAINS:      65536
[    0.001892] ... CHAINHASH_SIZE:          32768
[    0.001922]  memory used by lock dependency info: 5167 kB
[    0.001953]  per task-struct memory footprint: 1536 bytes
[    0.001983] Calibrating delay loop... 471.85 BogoMIPS (lpj=2359296)
[    0.091918] pid_max: default: 32768 minimum: 301
[    0.092620] Security Framework initialized
[    0.092895] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092926] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098968] Initializing cgroup subsys blkio
[    0.099151] Initializing cgroup subsys memory
[    0.099334] Initializing cgroup subsys devices
[    0.099517] Initializing cgroup subsys freezer
[    0.099761] Initializing cgroup subsys perf_event
[    0.099884] CPU: Testing write buffer coherency: ok
[    0.102722] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[    0.102966] Setting up static identity map for 0x80008280 - 0x800082f0
[    0.112091] Brought up 1 CPUs
[    0.112121] SMP: Total of 1 processors activated (471.85 BogoMIPS).
[    0.112152] CPU: All CPU(s) started in SVC mode.
[    0.118347] devtmpfs: initialized
[    0.275878] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[    0.390869] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp
[    0.393981] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp
[    0.508117] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.512573] pinctrl core: initialized pinctrl subsystem
[    0.522705] NET: Registered protocol family 16
[    0.535125] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.539642] cpuidle: using governor ladder
[    0.539703] cpuidle: using governor menu
[    0.540710] Reprogramming SDRC clock to 332000000 Hz
[    0.559295] omap_gpio 48310000.gpio: could not find pctldev for node /ocp/l4@48000000/scm@2000/pinmux@a00/pinmux_gpio1_pins, deferring probe
[    0.564666] OMAP GPIO hardware version 2.5
[    0.583801] irq: no irq domain found for /ocp/l4@48000000/scm@2000/pinmux@30 !
[    0.621398] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[    0.621734] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[    0.640533] No ATAGs?
[    0.640594] hw-breakpoint: debug architecture 0x4 unsupported.
[    0.646575] OMAP DMA hardware revision 4.0
[    0.720367] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver
[    0.729858] SCSI subsystem initialized
[    0.739837] omap_i2c 48070000.i2c: bus 0 rev3.3 at 2600 kHz
[    0.742553] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz
[    0.744903] omap_i2c 48060000.i2c: bus 2 rev3.3 at 100 kHz
[    0.754272] clocksource: Switched to clocksource 32k_counter
[    1.073364] NET: Registered protocol family 2
[    1.077423] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    1.077545] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
[    1.078918] TCP: Hash tables configured (established 2048 bind 2048)
[    1.079345] UDP hash table entries: 256 (order: 2, 20480 bytes)
[    1.079742] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[    1.081634] NET: Registered protocol family 1
[    1.085205] RPC: Registered named UNIX socket transport module.
[    1.085235] RPC: Registered udp transport module.
[    1.085266] RPC: Registered tcp transport module.
[    1.085296] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.093414] hw perfevents: Failed to parse /pmu/interrupt-affinity[0]
[    1.093719] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
[    1.105529] futex hash table entries: 256 (order: 2, 16384 bytes)
[    1.106048] audit: initializing netlink subsys (disabled)
[    1.106475] audit: type=2000 audit(1.130:1): initialized
[    1.115356] VFS: Disk quotas dquot_6.6.0
[    1.115631] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.120880] NFS: Registering the id_resolver key type
[    1.121734] Key type id_resolver registered
[    1.121765] Key type id_legacy registered
[    1.122100] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.131896] io scheduler noop registered
[    1.131958] io scheduler deadline registered
[    1.132049] io scheduler cfq registered (default)
[    1.137664] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568
[    1.138732] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
[    1.140533] pinctrl-single 480025d8.pinmux: 18 pins at pa fa0025d8 size 36
[    1.148956] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.162658] omap_uart 4806a000.serial: no wakeirq for uart0
[    1.163848] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[    1.168487] omap_uart 4806c000.serial: no wakeirq for uart1
[    1.169097] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    1.172668] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[    1.579467] console [ttyO2] enabled
[    1.647399] brd: module loaded
[    1.686126] loop: module loaded
[    1.705718] twl 0-0048: PIH (irq 23) chaining IRQs 307..315
[    1.709411] twl 0-0048: power (irq 312) chaining IRQs 315..322
[    1.798950] twl4030_gpio twl4030-gpio: gpio (irq 307) chaining IRQs 323..340
[    1.819976] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.826751] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xba
[    1.830169] nand: Micron MT29F2G16ABD
[    1.832153] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.836303] nand: using OMAP_ECC_HAM1_CODE_HW
[    1.838836] 5 ofpart partitions found on MTD device omap2-nand.0
[    1.842071] Creating 5 MTD partitions on "omap2-nand.0":
[    1.845001] 0x000000000000-0x000000080000 : "X-Loader"
[    1.859069] 0x000000080000-0x000000260000 : "U-Boot"
[    1.869720] 0x000000260000-0x000000280000 : "U-Boot Env"
[    1.879150] 0x000000280000-0x000000680000 : "Kernel"
[    1.892150] 0x000000680000-0x000010000000 : "Filesystem"
[    2.141143] mousedev: PS/2 mouse device common for all mice
[    2.144378] i2c /dev entries driver
[    2.205596] ledtrig-cpu: registered to indicate activity on CPUs
[    2.211761] oprofile: using arm/armv7
[    2.215393] Initializing XFRM netlink socket
[    2.217987] NET: Registered protocol family 17
[    2.220550] NET: Registered protocol family 15
[    2.223693] Key type dns_resolver registered
[    2.226654] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iva
[    2.230529] omap2_set_init_voltage: unable to set vdd_mpu_iva
[    2.233673] omap2_set_init_voltage: unable to find boot up OPP for vdd_core
[    2.237487] omap2_set_init_voltage: unable to set vdd_core
[    2.244537] PM: no software I/O chain control; some wakeups may be lost
[    2.251403] ThumbEE CPU extension supported.
[    2.253814] Registering SWP/SWPB emulation handler
[    2.256530] SmartReflex Class3 initialized
[    2.298675] hctosys: unable to open rtc device (rtc0)
[    2.301422] sr_init: No PMIC hook to init smartreflex
[    2.305175] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
[    2.309753] smartreflex smartreflex.0: omap_sr_probe: smartreflex_mpu_iva: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values
[    2.318267] smartreflex: probe of smartreflex.0 failed with error -61
[    2.322052] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
[    2.326599] smartreflex smartreflex.1: omap_sr_probe: smartreflex_core: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values
[    2.334655] smartreflex: probe of smartreflex.1 failed with error -61
[    2.338348] sr_init: platform driver register failed for SR
[    2.452880] hsusb2_vbus: disabling
[    2.456359] VUSB3V1: disabling
[    2.459289] VUSB1V8: disabling
[    2.462097] VUSB1V5: disabling
[    2.465698] VDAC: disabling
[    2.468749] VAUX3: disabling
[    2.480194] Waiting for root device /dev/mmcblk0p2...
[    2.495300] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.499938] mmc0: new SD card at address 8001
[    2.506988] mmcblk0: mmc0:8001 SD02G 1.89 GiB 
[    2.518524]  mmcblk0: p1 p2
[    3.893371] kjournald starting.  Commit interval 5 seconds
[    3.897125] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended
[    4.082153] EXT3-fs (mmcblk0p2): using internal journal
[    4.090820] EXT3-fs (mmcblk0p2): recovery complete
[    4.093414] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[    4.097442] VFS: Mounted root (ext3 filesystem) on device 179:2.
[    4.108123] devtmpfs: mounted
[    4.111480] Freeing unused kernel memory: 436K (c0853000 - c08c0000)
INIT: version 2.86 booting
Starting the hotplug events dispatcher udevd
[    5.675720] udevd (93): /proc/93/oom_adj is deprecated, please use /proc/93/oom_score_adj instead.
Synthesizing the initial hotplug events
[   18.522918] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
Remounting root file system...
mount: according to mtab, /proc is already mounted on /proc

WARNING: Couldn't open directory /lib/modules/4.2.0-158462-g64291f7: No such file or directory
FATAL: Could not open /lib/modules/4.2.0-158462-g64291f7/modules.dep.temp for writing: No such file or directory
root: mount: mount point /proc/bus/usb does not exist
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

ifconfig: SIOCGIFFLAGS: No such device
modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

eth0      No such device

modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

udhcpc: SIOCGIFINDEX: No such device
done.
Starting portmap daemon: portmap.
[   29.316406] random: nonblocking pool is initialized
hwclock: can't open '/dev/misc/rtc': No such file or directory
Tue Jul 22 00:18:00 UTC 2008
hwclock: can't open '/dev/misc/rtc': No such file or directory
INIT: Entering runlevel: 5
ALSA: Restoring mixer settings...
/usr/sbin/alsactl: load_state:1327: No soundcards found...
Starting Dropbear SSH server: modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

modprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

dropbear.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting system message bus: dbus.
Starting syslogd/klogd: start-stop-daemon: lseek: Invalid argument
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
Starting Bluetooth subsystem: hcidmodprobe: FATAL: Could not load /lib/modules/4.2.0-158462-g64291f7/modules.dep: No such file or directory

 hid2hci.

.-------.                                           
|       |                  .-.                      
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution beagleboard ttyO2

Angstrom 2008.1-test-20080712 beagleboard ttyO2

beagleboard login: 
.-------.                                           
|       |                  .-.                      
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution beagleboard ttyO2

Angstrom 2008.1-test-20080712 beagleboard ttyO2

beagleboard login: 
.-------.                                           
|       |                  .-.                      
|   |   |-----.-----.-----.| |   .----..-----.-----.
|       |     | __  |  ---'| '--.|  .-'|     |     |
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
                -'  |
                '---'

The Angstrom Distribution beagleboard ttyO2

Angstrom 2008.1-test-20080712 beagleboard ttyO2

beagleboard login: root
login[1385]: root login  on `ttyO2'

root@beagleboard:~# 
root@beagleboard:~# %% Start PM consolidated quick test


%% Preparation


root@beagleboard:~# 
root@beagleboard:~# mkdir -p /sys; mount -t sysfs none /sys
mount: none already mounted or /sys busy
mount: according to mtab, sysfs is already mounted on /sys
root@beagleboard:~# 
root@beagleboard:~# mkdir -p /debug; mount -t debugfs none /debug
mount: none already mounted or /debug busy
mount: according to mtab, debugfs is already mounted on /debug
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do echo -1 >  $u/power/autosuspend_delay_ms; done
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do ls -l  $u/power/autosuspend_delay_ms; cat $u/power/autos uspend_delay_ms; done
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806a000.serial/power/autosuspend_delay_ms
-1
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806c000.serial/power/autosuspend_delay_ms
-1
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/49020000.serial/power/autosuspend_delay_ms
-1
root@beagleboard:~# 
root@beagleboard:~# echo 0 > /debug/pm_debug/enable_off_mode
root@beagleboard:~# 
root@beagleboard:~# 
%% Baseline pm_debug count dump

cat /debug/pm_debug/count
usbhost_pwrdm (ON),OFF:0,RET:1041,INA:0,ON:1042,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
per_pwrdm (ON),OFF:0,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
dss_pwrdm (ON),OFF:0,RET:1041,INA:0,ON:1042,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
neon_pwrdm (ON),OFF:0,RET:543,INA:498,ON:1042,RET-LOGIC-OFF:0
mpu_pwrdm (ON),OFF:0,RET:543,INA:498,ON:1042,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
usbhost_clkdm->usbhost_pwrdm (1)
sgx_clkdm->sgx_pwrdm (0)
per_clkdm->per_pwrdm (12)
cam_clkdm->cam_pwrdm (0)
dss_clkdm->dss_pwrdm (1)
d2d_clkdm->core_pwrdm (0)
iva2_clkdm->iva2_pwrdm (0)
mpu_clkdm->mpu_pwrdm (0)
core_l4_clkdm->core_pwrdm (22)
core_l3_clkdm->core_pwrdm (1)
neon_clkdm->neon_pwrdm (0)
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/class/tty/ttyO* | paste -s -d' '`; do  echo enabled >  $u/power/wakeup; done
root@beagleboard:~#
%% Start retention double suspend/resume UART wakeup test

 
root@beagleboard:~# for u in `ls -1d /sys/class/tty/ttyO* | paste -s -d' '`; do  echo auto >  $u/power/control; done
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/class/tty/ttyO* | paste -s -d' '`; do  ls -l $u/power/wakeup; cat $u/power/wakeup; done
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/class/tty/ttyO0/power/wakeup
enabled
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/class/tty/ttyO1/power/wakeup
enabled
for u in `ls -1d /sys/class/tty/ttyO* | paste -s -d' '`; do ls -l $u/power/control; cat $u/power/control; done

-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/class/tty/ttyO2/power/wakeup
enabled
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/class/tty/ttyO* | paste -s -d' '`; do  ls -l $u/power/control; cat $u/power/control; done
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/class/tty/ttyO0/power/control
auto
echo mem > /sys/power/state

-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/class/tty/ttyO1/power/control
auto
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/class/tty/ttyO2/power/control
auto
root@beagleboard:~# 
root@beagleboard:~# echo mem > /sys/power/state
[   42.087982] PM: Syncing filesystems ... done.
[   42.658538] Freezing user space processes ... (elapsed 0.005 seconds) done.
[   42.668395] Freezing remaining freezable tasks ... (elapsed 0.003 seconds) done.
[   42.676422] Suspending console(s) (use no_console_suspend to debug)
[   42.708526] PM: suspend of devices complete after 20.935 msecs
[   42.717407] PM: late suspend of devices complete after 8.819 msecs
[   42.729614] PM: noirq suspend of devices complete after 12.145 msecs
[   42.729736] Disabling non-boot CPUs ...
[   42.729797] Successfully put all powerdomains to target state
[   42.735595] PM: noirq resume of devices complete after 5.706 msecs
[   42.742980] PM: early resume of devices complete after 5.767 msecs
[   42.917785] PM: resume of devices complete after 174.560 msecs
[   42.951110] Restarting tasks ... done.
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# cat /debug/pm_debug/count
usbhost_pwrdm (ON),OFF:0,RET:1149,INA:0,ON:1150,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
per_pwrdm (ON),OFF:0,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
dss_pwrdm (ON),OFF:0,RET:1149,INA:0,ON:1150,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
neon_pwrdm (ON),OFF:0,RET:643,INA:506,ON:1150,RET-LOGIC-OFF:0
mpu_pwrdm (ON),OFF:0,RET:643,INA:506,ON:1150,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
usbhost_clkdm->usbhost_pwrdm (1)
sgx_clkdm->sgx_pwrdm (0)
per_clkdm->per_pwrdm (12)
cam_clkdm->cam_pwrdm (0)
dss_clkdm->dss_pwrdm (1)
d2d_clkdm->core_pwrdm (0)
iva2_clkdm->iva2_pwrdm (0)
mpu_clkdm->mpu_pwrdm (0)
core_l4_clkdm->core_pwrdm (27)
core_l3_clkdm->core_pwrdm (1)
neon_clkdm->neon_pwrdm (0)
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# echo mem > /sys/power/state
[   44.951812] PM: Syncing filesystems ... done.
[   45.683807] Freezing user space processes ... (elapsed 0.002 seconds) done.
[   45.690124] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
[   45.696685] Suspending console(s) (use no_console_suspend to debug)
[   45.723236] PM: suspend of devices complete after 16.387 msecs
[   45.731964] PM: late suspend of devices complete after 8.666 msecs
[   45.741729] PM: noirq suspend of devices complete after 9.704 msecs
[   45.741760] Disabling non-boot CPUs ...
[   45.741790] Successfully put all powerdomains to target state
[   45.747253] PM: noirq resume of devices complete after 5.371 msecs
[   45.754791] PM: early resume of devices complete after 5.981 msecs
[   45.926635] PM: resume of devices complete after 171.691 msecs
[   45.958496] Restarting tasks ... done.
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# cat /debug/pm_debug/count
usbhost_pwrdm (ON),OFF:0,RET:1246,INA:0,ON:1247,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
per_pwrdm (ON),OFF:0,RET:2,INA:0,ON:3,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
dss_pwrdm (ON),OFF:0,RET:1246,INA:0,ON:1247,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
neon_pwrdm (ON),OFF:0,RET:737,INA:509,ON:1247,RET-LOGIC-OFF:0
mpu_pwrdm (ON),OFF:0,RET:737,INA:509,ON:1247,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
usbhost_clkdm->usbhost_pwrdm (1)
sgx_clkdm->sgx_pwrdm (0)
per_clkdm->per_pwrdm (12)
cam_clkdm->cam_pwrdm (0)
dss_clkdm->dss_pwrdm (1)
d2d_clkdm->core_pwrdm (0)
iva2_clkdm->iva2_pwrdm (0)
mpu_clkdm->mpu_pwrdm (0)
core_l4_clkdm->core_pwrdm (27)
core_l3_clkdm->core_pwrdm (1)
neon_clkdm->neon_pwrdm (0)
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# ./test_rootfs_access_nonexistent_file__ret_susp
-sh: ./test_rootfs_access_nonexistent_file__ret_susp: not found
root@beagleboard:~# 
root@beagleboard:~# 
%% End retention double suspend/resume UART wakeup test


%% Start retention dynamic idle UART wakeup test

for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do echo 3000 >  $u/power/autosuspend_delay_ms; done
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do ls -l  $u/power/autosuspend_delay_ms; cat $u/power/autos uspend_delay_ms; done
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806a000.serial/power/autosuspend_delay_ms
3000
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806c000.serial/power/autosuspend_delay_ms
3000
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/49020000.serial/power/autosuspend_delay_ms
3000
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# cat /debug/pm_debug/count
usbhost_pwrdm (ON),OFF:0,RET:1401,INA:0,ON:1402,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:0,RET:13,INA:5,ON:19,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
per_pwrdm (ON),OFF:0,RET:18,INA:0,ON:19,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
dss_pwrdm (ON),OFF:0,RET:1401,INA:0,ON:1402,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
neon_pwrdm (ON),OFF:0,RET:888,INA:513,ON:1402,RET-LOGIC-OFF:0
mpu_pwrdm (ON),OFF:0,RET:888,INA:513,ON:1402,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
iva2_pwrdm (RET),OFF:0,RET:1,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
usbhost_clkdm->usbhost_pwrdm (1)
sgx_clkdm->sgx_pwrdm (0)
per_clkdm->per_pwrdm (12)
cam_clkdm->cam_pwrdm (0)
dss_clkdm->dss_pwrdm (1)
d2d_clkdm->core_pwrdm (0)
iva2_clkdm->iva2_pwrdm (0)
mpu_clkdm->mpu_pwrdm (0)
core_l4_clkdm->core_pwrdm (20)
core_l3_clkdm->core_pwrdm (1)
neon_clkdm->neon_pwrdm (0)
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# ./test_rootfs_access_nonexistent_file__ret_dyn
-sh: ./test_rootfs_access_nonexistent_file__ret_dyn: not found
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do echo -1 >  $u/power/autosuspend_delay_ms; done
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do ls -l  $u/power/autosuspend_delay_ms; cat $u/power/autos uspend_delay_ms; done
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806a000.serial/power/autosuspend_delay_ms
-1
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806c000.serial/power/autosuspend_delay_ms
-1
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/49020000.serial/power/autosuspend_delay_ms
-1
root@beagleboard:~# 
root@beagleboard:~# 
%% End retention dynamic idle UART wakeup test


%% Start off-mode double suspend UART wakeup test

echo 1 > /debug/pm_debug/enable_off_mode
root@beagleboard:~# 
root@beagleboard:~# echo mem > /sys/power/state
[   66.769287] PM: Syncing filesystems ... done.
[   67.157928] Freezing user space processes ... (elapsed 0.002 seconds) done.
[   67.164337] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
[   67.170837] Suspending console(s) (use no_console_suspend to debug)
[   67.197357] PM: suspend of devices complete after 16.479 msecs
[   67.206146] PM: late suspend of devices complete after 8.758 msecs
[   67.215881] PM: noirq suspend of devices complete after 9.704 msecs
[   67.215911] Disabling non-boot CPUs ...
[   67.215911] Successfully put all powerdomains to target state
[   67.235351] PM: noirq resume of devices complete after 19.317 msecs
[   67.242675] PM: early resume of devices complete after 5.767 msecs
[   67.416442] PM: resume of devices complete after 173.614 msecs
[   67.448333] Restarting tasks ... done.
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# cat /debug/pm_debug/count
usbhost_pwrdm (ON),OFF:119,RET:1489,INA:0,ON:1609,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:1,RET:13,INA:5,ON:20,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
per_pwrdm (ON),OFF:1,RET:18,INA:0,ON:20,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
dss_pwrdm (ON),OFF:119,RET:1489,INA:0,ON:1609,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
neon_pwrdm (ON),OFF:1,RET:1083,INA:524,ON:1609,RET-LOGIC-OFF:0
mpu_pwrdm (ON),OFF:1,RET:1083,INA:524,ON:1609,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
iva2_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
usbhost_clkdm->usbhost_pwrdm (1)
sgx_clkdm->sgx_pwrdm (0)
per_clkdm->per_pwrdm (12)
cam_clkdm->cam_pwrdm (0)
dss_clkdm->dss_pwrdm (1)
d2d_clkdm->core_pwrdm (0)
iva2_clkdm->iva2_pwrdm (0)
mpu_clkdm->mpu_pwrdm (0)
core_l4_clkdm->core_pwrdm (27)
core_l3_clkdm->core_pwrdm (1)
neon_clkdm->neon_pwrdm (0)
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# echo mem > /sys/power/state
[   69.431762] PM: Syncing filesystems ... done.
[   70.164459] Freezing user space processes ... (elapsed 0.002 seconds) done.
[   70.170745] Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
[   70.177429] Suspending console(s) (use no_console_suspend to debug)
[   70.204040] PM: suspend of devices complete after 16.510 msecs
[   70.212585] PM: late suspend of devices complete after 8.483 msecs
[   70.222320] PM: noirq suspend of devices complete after 9.674 msecs
[   70.222351] Disabling non-boot CPUs ...
[   70.222381] Successfully put all powerdomains to target state
[   70.241790] PM: noirq resume of devices complete after 19.287 msecs
[   70.249328] PM: early resume of devices complete after 5.767 msecs
[   70.396331] PM: resume of devices complete after 146.850 msecs
[   70.428253] Restarting tasks ... done.
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# cat /debug/pm_debug/count
usbhost_pwrdm (ON),OFF:218,RET:1489,INA:0,ON:1708,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:2,RET:13,INA:5,ON:21,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
per_pwrdm (ON),OFF:2,RET:18,INA:0,ON:21,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
dss_pwrdm (ON),OFF:218,RET:1489,INA:0,ON:1708,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
neon_pwrdm (ON),OFF:2,RET:1176,INA:529,ON:1708,RET-LOGIC-OFF:0
mpu_pwrdm (ON),OFF:2,RET:1176,INA:529,ON:1708,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
iva2_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
usbhost_clkdm->usbhost_pwrdm (1)
sgx_clkdm->sgx_pwrdm (0)
per_clkdm->per_pwrdm (12)
cam_clkdm->cam_pwrdm (0)
dss_clkdm->dss_pwrdm (1)
d2d_clkdm->core_pwrdm (0)
iva2_clkdm->iva2_pwrdm (0)
mpu_clkdm->mpu_pwrdm (0)
core_l4_clkdm->core_pwrdm (27)
core_l3_clkdm->core_pwrdm (1)
neon_clkdm->neon_pwrdm (0)
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# ./test_rootfs_access_nonexistent_file__off_susp
-sh: ./test_rootfs_access_nonexistent_file__off_susp: not found
root@beagleboard:~# 
root@beagleboard:~# 
%% End off-mode double suspend UART wakeup test


%% Start off-mode dynamic idle UART wakeup test

for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do echo 3000 >  $u/power/autosuspend_delay_ms; done
root@beagleboard:~# 
root@beagleboard:~# for u in `ls -1d /sys/bus/platform/drivers/omap_uart/*.seria l | paste -s -d' '`; do ls -l  $u/power/autosuspend_delay_ms; cat $u/power/autos uspend_delay_ms; done
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806a000.serial/power/autosuspend_delay_ms
3000
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/4806c000.serial/power/autosuspend_delay_ms
3000
-rw-r--r--    1 root     root         4096 Jul 22 00:18 /sys/bus/platform/drivers/omap_uart/49020000.serial/power/autosuspend_delay_ms
3000
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# cat /debug/pm_debug/count
usbhost_pwrdm (ON),OFF:368,RET:1489,INA:0,ON:1858,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
sgx_pwrdm (OFF),OFF:1,RET:0,INA:0,ON:1,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
core_pwrdm (ON),OFF:8,RET:17,INA:7,ON:33,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0
per_pwrdm (ON),OFF:12,RET:20,INA:0,ON:33,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
dss_pwrdm (ON),OFF:368,RET:1489,INA:0,ON:1858,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
cam_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
neon_pwrdm (ON),OFF:13,RET:1311,INA:533,ON:1858,RET-LOGIC-OFF:0
mpu_pwrdm (ON),OFF:13,RET:1311,INA:533,ON:1858,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0
iva2_pwrdm (OFF),OFF:1,RET:1,INA:0,ON:2,RET-LOGIC-OFF:0,RET-MEMBANK1-OFF:0,RET-MEMBANK2-OFF:0,RET-MEMBANK3-OFF:0,RET-MEMBANK4-OFF:0
usbhost_clkdm->usbhost_pwrdm (1)
sgx_clkdm->sgx_pwrdm (0)
per_clkdm->per_pwrdm (12)
cam_clkdm->cam_pwrdm (0)
dss_clkdm->dss_pwrdm (1)
d2d_clkdm->core_pwrdm (0)
iva2_clkdm->iva2_pwrdm (0)
mpu_clkdm->mpu_pwrdm (0)
core_l4_clkdm->core_pwrdm (20)
core_l3_clkdm->core_pwrdm (1)
neon_clkdm->neon_pwrdm (0)
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# 
root@beagleboard:~# ./test_rootfs_access_nonexistent_file__off_dyn
-sh: ./test_rootfs_access_nonexistent_file__off_dyn: not found
root@beagleboard:~# 
root@beagleboard:~# 
%% End off-mode dynamic idle UART wakeup test


%% End PM consolidated quick test