U-Boot SPL 2014.07-rc2-00015-g713ff68 (Jun 03 2014 - 09:09:41) OMAP5432 ES2.0 SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! reading u-boot.img reading u-boot.img U-Boot 2014.07-rc2-00015-g713ff68 (Jun 03 2014 - 09:09:41), Build: jenkins-github_Bootloader-Builder-315 CPU : OMAP5432 ES2.0 Board: OMAP5432 uEVM I2C: ready DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: No ethernet found. Hit any key to stop autoboot: 5  0 U-Boot# U-Boot# setenv bootargs 'console=ttyO2,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh' U-Boot# loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 115200 bps... CSending: uImage-dtb.omap5-uevm Sending: Transfer complete - CRC mode, 5(SOH)/3552(STX)/0(CAN) packets, 3 retries ## Total Size = 0x00378143 = 3637571 Bytes U-Boot# bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3637507 Bytes = 3.5 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.3.0-rc3-170676-g9ffecb1 (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Sun Sep 27 22:34:43 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI OMAP5 uEVM board [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0xfd800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OMAP4: Map 0xfee00000 to fe600000 for dram barrier [ 0.000000] On node 0 totalpages: 519680 [ 0.000000] free_area_init_node: node 0, pgdat c09c4240, node_mem_map ee61d000 [ 0.000000] Normal zone: 1710 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 325120 pages, LIFO batch:31 [ 0.000000] OMAP5432 ES2.0 [ 0.000000] PERCPU: Embedded 14 pages/cpu @ee5ad000 s25088 r8192 d24064 u57344 [ 0.000000] pcpu-alloc: s25088 r8192 d24064 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517970 [ 0.000000] Kernel command line: console=ttyO2,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2024456K/2078720K available (6566K kernel code, 744K rwdata, 2224K rodata, 456K init, 8263K bss, 37880K reserved, 16384K cma-reserved, 1284096K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc089dc18 (8792 kB) [ 0.000000] .init : 0xc089e000 - 0xc0910000 ( 456 kB) [ 0.000000] .data : 0xc0910000 - 0xc09ca1d8 ( 745 kB) [ 0.000000] .bss : 0xc09cd000 - 0xc11deeb8 (8264 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000457] Architected cp15 timer(s) running at 6.14MHz (virt). [ 0.000457] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16ac02862, max_idle_ns: 440795202218 ns [ 0.000493] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511085ns [ 0.000503] Switching to timer-based delay loop, resolution 162ns [ 0.001568] Console: colour dummy device 80x30 [ 0.001601] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001608] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001614] ... MAX_LOCK_DEPTH: 48 [ 0.001620] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001626] ... CLASSHASH_SIZE: 4096 [ 0.001632] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001638] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001643] ... CHAINHASH_SIZE: 32768 [ 0.001649] memory used by lock dependency info: 5167 kB [ 0.001655] per task-struct memory footprint: 1536 bytes [ 0.001674] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440) [ 0.001687] pid_max: default: 32768 minimum: 301 [ 0.001963] Security Framework initialized [ 0.002063] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002075] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004225] Initializing cgroup subsys io [ 0.004300] Initializing cgroup subsys memory [ 0.004365] Initializing cgroup subsys devices [ 0.004424] Initializing cgroup subsys freezer [ 0.004510] Initializing cgroup subsys perf_event [ 0.004559] CPU: Testing write buffer coherency: ok [ 0.005448] /cpus/cpu@0 missing clock-frequency property [ 0.005468] /cpus/cpu@1 missing clock-frequency property [ 0.005479] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005535] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.009861] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.010258] Brought up 2 CPUs [ 0.010271] SMP: Total of 2 processors activated (24.57 BogoMIPS). [ 0.010278] CPU: All CPU(s) started in SVC mode. [ 0.012910] devtmpfs: initialized [ 0.054534] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.055849] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.057073] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.166693] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.167737] pinctrl core: initialized pinctrl subsystem [ 0.171325] NET: Registered protocol family 16 [ 0.174793] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.200991] cpuidle: using governor ladder [ 0.230974] cpuidle: using governor menu [ 0.240652] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.241340] OMAP GPIO hardware version 0.1 [ 0.242268] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.243727] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.245130] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.246554] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.247969] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.249392] gpiochip_add: registered GPIOs 192 to 223 on device: gpio [ 0.250810] gpiochip_add: registered GPIOs 224 to 255 on device: gpio [ 0.251817] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc' [ 0.252025] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 0.252041] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.252121] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x10000000 [ 0.257309] irq: no irq domain found for /ocp/l4@4a000000/scm@2800/pinmux@40 ! [ 0.277867] No ATAGs? [ 0.277925] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.277933] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.280023] OMAP DMA hardware revision 0.0 [ 0.332011] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.332835] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-mmcsd[0]' [ 0.336388] SCSI subsystem initialized [ 0.336722] libata version 3.00 loaded. [ 0.337287] usb_phy_generic hsusb2_phy: GPIO lookup for consumer reset [ 0.337297] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.337330] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0) [ 0.337379] no flags found for reset [ 0.337391] usb_phy_generic hsusb2_phy: GPIO lookup for consumer vbus-detect [ 0.337400] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.337410] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb2_phy[0]' [ 0.337420] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb2_phy[0]' [ 0.337428] usb_phy_generic hsusb2_phy: using lookup tables for GPIO lookup [ 0.337491] usb_phy_generic hsusb2_phy: lookup for GPIO vbus-detect failed [ 0.337537] hsusb2_phy supply vcc not found, using dummy regulator [ 0.337915] usb_phy_generic hsusb3_phy: GPIO lookup for consumer reset [ 0.337924] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.337947] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb3_phy[0]' - status (0) [ 0.337960] no flags found for reset [ 0.337971] usb_phy_generic hsusb3_phy: GPIO lookup for consumer vbus-detect [ 0.337979] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.337989] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb3_phy[0]' [ 0.337998] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb3_phy[0]' [ 0.338006] usb_phy_generic hsusb3_phy: using lookup tables for GPIO lookup [ 0.338016] usb_phy_generic hsusb3_phy: lookup for GPIO vbus-detect failed [ 0.338049] hsusb3_phy supply vcc not found, using dummy regulator [ 0.338585] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c1_pins, deferring probe [ 0.339751] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz [ 0.340519] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 0.341264] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 100 kHz [ 0.341346] omap_i2c 4807c000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c5_pins, deferring probe [ 0.341647] pps_core: LinuxPPS API ver. 1 registered [ 0.341655] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.341696] PTP clock support registered [ 0.344411] clocksource: Switched to clocksource arch_sys_counter [ 0.449895] NET: Registered protocol family 2 [ 0.451214] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.451340] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.453685] TCP: Hash tables configured (established 8192 bind 8192) [ 0.453820] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.454137] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.455095] NET: Registered protocol family 1 [ 0.456019] RPC: Registered named UNIX socket transport module. [ 0.456028] RPC: Registered udp transport module. [ 0.456036] RPC: Registered tcp transport module. [ 0.456043] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.495593] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.499732] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.499981] audit: initializing netlink subsys (disabled) [ 0.500092] audit: type=2000 audit(0.490:1): initialized [ 0.502611] VFS: Disk quotas dquot_6.6.0 [ 0.502718] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.504519] NFS: Registering the id_resolver key type [ 0.504755] Key type id_resolver registered [ 0.504764] Key type id_legacy registered [ 0.504892] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.508501] bounce: pool size: 64 pages [ 0.508558] io scheduler noop registered [ 0.508573] io scheduler deadline registered [ 0.508604] io scheduler cfq registered (default) [ 0.511998] ti-pipe3 4a096000.phy: can't get syscon-pllreset, sata dpll won't idle [ 0.513465] pinctrl-single 4a002840.pinmux: 219 pins at pa fc002840 size 438 [ 0.513897] pinctrl-single 4ae0c840.pinmux: 28 pins at pa fce0c840 size 56 [ 0.518825] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.523122] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.523136] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.523422] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 306, base_baud = 3000000) is a OMAP UART0 [ 0.524578] omap_uart 4806c000.serial: no wakeirq for uart1 [ 0.524590] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 0.524773] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 307, base_baud = 3000000) is a OMAP UART1 [ 0.525685] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48020000[0]' [ 0.525868] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 308, base_baud = 3000000) is a OMAP UART2 [ 1.691226] console [ttyO2] enabled [ 1.695939] omap_uart 4806e000.serial: no wakeirq for uart3 [ 1.701767] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 1.711822] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 309, base_baud = 3000000) is a OMAP UART3 [ 1.722395] omap_uart 48066000.serial: no wakeirq for uart4 [ 1.728245] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48066000[0]' [ 1.738259] 48066000.serial: ttyO4 at MMIO 0x48066000 (irq = 310, base_baud = 3000000) is a OMAP UART4 [ 1.748774] omap_uart 48068000.serial: no wakeirq for uart5 [ 1.754618] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48068000[0]' [ 1.764624] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 311, base_baud = 3000000) is a OMAP UART5 [ 1.798570] brd: module loaded [ 1.816193] loop: module loaded [ 1.821713] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 1.828765] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.837698] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 1.849885] scsi host0: ahci [ 1.853765] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 338 [ 1.862852] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.878191] mousedev: PS/2 mouse device common for all mice [ 1.884024] i2c /dev entries driver [ 1.890068] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 1.896369] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.903193] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.912744] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.922218] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.929235] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 1.935349] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 1.941630] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.948470] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.958043] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.967506] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.974517] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 2.005767] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 2.012042] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 2.018896] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.028468] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.037946] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.044971] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 2.051074] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 2.057365] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 2.064191] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.073756] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.083233] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.090258] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 2.134632] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer cd [ 2.140912] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.147760] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.157324] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.166790] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.173805] omap_hsmmc 480ad000.mmc: lookup for GPIO cd failed [ 2.179923] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.186222] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.193047] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.197851] mmc0: MAN_BKOPS_EN bit is not set [ 2.199749] mmc0: new high speed MMC card at address 0001 [ 2.201537] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.202178] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.202751] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.229925] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.234400] ata1: SATA link down (SStatus 0 SControl 300) [ 2.245056] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.252065] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.294699] ledtrig-cpu: registered to indicate activity on CPUs [ 2.302685] oprofile: using timer interrupt. [ 2.307610] Initializing XFRM netlink socket [ 2.312348] NET: Registered protocol family 10 [ 2.318683] sit: IPv6 over IPv4 tunneling driver [ 2.325081] NET: Registered protocol family 17 [ 2.329767] NET: Registered protocol family 15 [ 2.334676] Key type dns_resolver registered [ 2.339295] omap_vc_init_channel: No PMIC info for vdd_core [ 2.345138] omap_vp_init: No PMIC info for vdd_core [ 2.350242] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.355903] omap_vp_init: No PMIC info for vdd_mm [ 2.360833] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.366588] omap_vp_init: No PMIC info for vdd_mpu [ 2.372239] Power Management for TI OMAP4+ devices. [ 2.377590] ThumbEE CPU extension supported. [ 2.382079] Registering SWP/SWPB emulation handler [ 2.387127] SmartReflex Class3 initialized [ 2.397151] palmas 0-0048: Irq flag is 0x00000000 [ 2.418505] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.475722] twl6040 0-004b: clk32k is not handled [ 2.482890] of_get_named_gpiod_flags: parsed 'ti,audpwron-gpio' property of node '/ocp/i2c@48070000/twl@4b[0]' - status (0) [ 2.496614] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.504231] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.510476] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 2.516791] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.523633] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.533221] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 2.542720] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 2.549773] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 2.555912] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 2.562210] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.569072] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.578660] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 2.588150] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 2.595199] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 2.645899] hctosys: unable to open rtc device (rtc0) [ 2.651196] sr_init: No PMIC hook to init smartreflex [ 2.656712] sr_init: platform driver register failed for SR [ 2.692178] ldo3: disabling [ 2.696254] ldo8: disabling [ 2.701862] Waiting for root device /dev/mmcblk1p2... [ 2.703085] mmc2: host does not support reading read-only switch, assuming write-enable [ 2.703236] mmc2: new SD card at address d91a [ 2.704507] mmcblk1: mmc2:d91a SU02G 1.84 GiB [ 2.706668] mmcblk1: p1 p2 [ 2.729497] EXT2-fs (mmcblk1p2): error: couldn't mount because of unsupported optional features (240) [ 2.740345] EXT4-fs (mmcblk1p2): couldn't mount as ext3 due to feature incompatibilities [ 2.768497] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.777099] VFS: Mounted root (ext4 filesystem) readonly on device 179:26. [ 2.798146] devtmpfs: mounted [ 2.801664] Freeing unused kernel memory: 456K (c089e000 - c0910000) /bin/sh: 0: can't access tty; job control turned off # # #