CCSending /srv/serial/u-boot-spl.bin, 784 blocks: Give your local XMODEM receive command now. Transfer complete t SPL 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 CSending: u-boot.bin Sending: Transfer complete - CRC mode, 3(SOH)/375(STX)/0(CAN) packets, 3 retries Loaded 384084 bytes U-Boot 2013.04-00235-g48e0b2b (May 18 2013 - 18:06:38) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 1  0 Card did not respond to voltage select! mmc0(part 0) is current device Card did not respond to voltage select! Booting from nand ... no devices available Wrong Image Format for bootm command ERROR: can't get kernel image! U-Boot# a askenv - get environment variables from stdin Usage: askenv name [message] [size] - get environment variable 'name' from stdin (max 'size' chars) U-Boot# setenv autoload off; setenv serverip 192.168.57.1; dhcp cpsw Waiting for PHY auto negotiation to complete. done link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.57.138 U-Boot# tftp 0x81000000 zImage.omap2plus_defconfig link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'zImage.omap2plus_defconfig'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################## 951.2 KiB/s done Bytes transferred = 3583464 (36ade8 hex) U-Boot# tftp 0x82000000 am335x-bone.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.57.1; our IP address is 192.168.57.138 Filename 'am335x-bone.dtb'. Load address: 0x82000000 Loading: *### 834 KiB/s done Bytes transferred = 30756 (7824 hex) U-Boot# setenv bootargs console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp U-Boot# U-Boot# bootz 0x81000000 - 0x82000000 ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Using Device Tree in place at 82000000, end 8200a823 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.3.0-rc5-171159-g25cb62b (paul@knihy) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Sun Oct 11 16:12:41 MDT 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI AM335x BeagleBone [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x8e800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 65024 [ 0.000000] free_area_init_node: node 0, pgdat c09c1ac0, node_mem_map cfbb1000 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65024 pages, LIFO batch:15 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] PERCPU: Embedded 14 pages/cpu @cfb5a000 s25088 r8192 d24064 u57344 [ 0.000000] pcpu-alloc: s25088 r8192 d24064 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64448 [ 0.000000] Kernel command line: console=ttyO0,115200n8 rw debug ignore_loglevel earlyprintk root=/dev/nfs nfsroot=192.168.57.1:/srv/nfs4/rootfs2 nfsrootdebug ip=dhcp [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 222508K/260096K available (6562K kernel code, 742K rwdata, 2224K rodata, 452K init, 8263K bss, 21204K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc089cb8c (8787 kB) [ 0.000000] .init : 0xc089d000 - 0xc090e000 ( 452 kB) [ 0.000000] .data : 0xc090e000 - 0xc09c7a58 ( 743 kB) [ 0.000000] .bss : 0xc09ca000 - 0xc11dbe78 (8264 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz [ 0.000021] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000058] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000129] OMAP clocksource: timer1 at 24000000 Hz [ 0.001496] Console: colour dummy device 80x30 [ 0.001587] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001602] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001615] ... MAX_LOCK_DEPTH: 48 [ 0.001628] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001641] ... CLASSHASH_SIZE: 4096 [ 0.001654] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001667] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001679] ... CHAINHASH_SIZE: 32768 [ 0.001692] memory used by lock dependency info: 5167 kB [ 0.001706] per task-struct memory footprint: 1536 bytes [ 0.001744] Calibrating delay loop... 545.58 BogoMIPS (lpj=2727936) [ 0.097864] pid_max: default: 32768 minimum: 301 [ 0.098493] Security Framework initialized [ 0.098712] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.098739] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.103762] Initializing cgroup subsys io [ 0.103958] Initializing cgroup subsys memory [ 0.104119] Initializing cgroup subsys devices [ 0.104276] Initializing cgroup subsys freezer [ 0.104484] Initializing cgroup subsys perf_event [ 0.104590] CPU: Testing write buffer coherency: ok [ 0.106931] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.107112] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.113550] Brought up 1 CPUs [ 0.113583] SMP: Total of 1 processors activated (545.58 BogoMIPS). [ 0.113600] CPU: All CPU(s) started in SVC mode. [ 0.120404] devtmpfs: initialized [ 0.174394] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 0.248371] omap_hwmod: tptc0 using broken dt data from edma [ 0.249179] omap_hwmod: tptc1 using broken dt data from edma [ 0.249976] omap_hwmod: tptc2 using broken dt data from edma [ 0.263039] omap_hwmod: debugss: _wait_target_disable failed [ 0.322187] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.325507] pinctrl core: initialized pinctrl subsystem [ 0.334678] NET: Registered protocol family 16 [ 0.344880] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.348600] cpuidle: using governor ladder [ 0.348645] cpuidle: using governor menu [ 0.363074] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.364547] OMAP GPIO hardware version 0.1 [ 0.366750] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.370269] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.373510] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.396019] No ATAGs? [ 0.396065] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.399529] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.399568] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.469734] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.470509] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator@0[0]' [ 0.476263] SCSI subsystem initialized [ 0.477464] libata version 3.00 loaded. [ 0.479472] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe [ 0.479647] omap_i2c 4819c000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring probe [ 0.480049] pps_core: LinuxPPS API ver. 1 registered [ 0.480068] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.480164] PTP clock support registered [ 0.487052] clocksource: Switched to clocksource timer1 [ 0.731999] NET: Registered protocol family 2 [ 0.735312] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.735422] TCP bind hash table entries: 2048 (order: 4, 73728 bytes) [ 0.736663] TCP: Hash tables configured (established 2048 bind 2048) [ 0.737194] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.737545] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.739225] NET: Registered protocol family 1 [ 0.741960] RPC: Registered named UNIX socket transport module. [ 0.741993] RPC: Registered udp transport module. [ 0.742010] RPC: Registered tcp transport module. [ 0.742027] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.745817] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 0.753201] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.753585] audit: initializing netlink subsys (disabled) [ 0.753992] audit: type=2000 audit(0.740:1): initialized [ 0.761097] VFS: Disk quotas dquot_6.6.0 [ 0.761334] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.765393] NFS: Registering the id_resolver key type [ 0.766085] Key type id_resolver registered [ 0.766109] Key type id_legacy registered [ 0.766460] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.776269] io scheduler noop registered [ 0.776320] io scheduler deadline registered [ 0.776404] io scheduler cfq registered (default) [ 0.779958] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.783963] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.793818] omap_uart 44e09000.serial: no wakeirq for uart0 [ 0.793865] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@44e09000[0]' [ 0.794773] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 155, base_baud = 3000000) is a OMAP UART0 [ 1.633609] console [ttyO0] enabled [ 1.700543] brd: module loaded [ 1.742328] loop: module loaded [ 1.749796] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.765537] mousedev: PS/2 mouse device common for all mice [ 1.771577] i2c /dev entries driver [ 1.777645] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 1.783965] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.790964] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 1.801476] omap_hsmmc 48060000.mmc: Got CD GPIO [ 1.806339] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 1.812699] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 1.819605] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 1.829233] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 1.838765] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 1.846020] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 1.857201] ledtrig-cpu: registered to indicate activity on CPUs [ 1.865341] oprofile: using arm/armv7 [ 1.870577] Initializing XFRM netlink socket [ 1.875743] NET: Registered protocol family 10 [ 1.885406] sit: IPv6 over IPv4 tunneling driver [ 1.894170] NET: Registered protocol family 17 [ 1.899098] NET: Registered protocol family 15 [ 1.904379] Key type dns_resolver registered [ 1.909413] omap_voltage_late_init: Voltage driver support not added [ 1.916105] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize [ 1.924661] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize [ 1.935006] ThumbEE CPU extension supported. [ 1.939659] Registering SWP/SWPB emulation handler [ 1.944706] SmartReflex Class3 initialized [ 2.013541] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 2.020111] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 2.032815] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz [ 2.040091] omap_hsmmc 48060000.mmc: GPIO lookup for consumer cd [ 2.046411] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 2.053434] of_get_named_gpiod_flags: parsed 'cd-gpios' property of node '/ocp/mmc@48060000[0]' - status (0) [ 2.063954] omap_hsmmc 48060000.mmc: Got CD GPIO [ 2.068879] omap_hsmmc 48060000.mmc: GPIO lookup for consumer wp [ 2.075185] omap_hsmmc 48060000.mmc: using device tree for GPIO lookup [ 2.082081] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@48060000[0]' [ 2.091705] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@48060000[0]' [ 2.101230] omap_hsmmc 48060000.mmc: using lookup tables for GPIO lookup [ 2.108321] omap_hsmmc 48060000.mmc: lookup for GPIO wp failed [ 2.226966] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.233388] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.245913] libphy: 4a101000.mdio: probed [ 2.250331] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.262126] cpsw 4a100000.ethernet: Detected MACID = 78:c5:e5:c3:1e:2a [ 2.274939] hctosys: unable to open rtc device (rtc0) [ 2.280435] sr_init: No PMIC hook to init smartreflex [ 2.286150] sr_init: platform driver register failed for SR [ 2.329180] net eth0: initializing cpsw version 1.12 (0) [ 2.337670] net eth0: phy found : id is : 0x7c0f1 [ 2.342820] libphy: PHY 4a101000.mdio:01 not found [ 2.347921] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 2.365560] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.357578] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 5.367078] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.386942] Sending DHCP requests ., OK [ 5.407526] IP-Config: Got DHCP answer from 192.168.57.1, my address is 192.168.57.138 [ 5.416582] IP-Config: Complete: [ 5.420129] device=eth0, hwaddr=78:c5:e5:c3:1e:2a, ipaddr=192.168.57.138, mask=255.255.255.0, gw=255.255.255.255 [ 5.431302] host=192.168.57.138, domain=example.org, nis-domain=(none) [ 5.438643] bootserver=0.0.0.0, rootserver=192.168.57.1, rootpath= [ 5.445397] nameserver0=192.168.57.1 [ 5.450093] vmmcsd_fixed: disabling [ 5.488418] VFS: Mounted root (nfs filesystem) on device 0:15. [ 5.497711] devtmpfs: mounted [ 5.502100] Freeing unused kernel memory: 452K (c089d000 - c090e000) INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 8.782519] udevd[166]: starting version 175 [ ok . [....] Synthesizing the initial hotplug events...udevd[196]: error changing net interface name eth0 to eth4: Device or resource busy [ ok done. [....] Waiting for /dev to be fully populated...[ ok done. [ 16.921756] random: nonblocking pool is initialized [....] Activating swap...[ ok done. [....] Cleaning up temporary files... /tmp[ ok . [....] Activating lvm and md swap...[ ok done. [....] Checking file systems...fsck from util-linux 2.20.1 [ ok done. [....] Mounting local filesystems...[ ok done. [....] Activating swapfile swap...[ ok done. [....] Cleaning up temporary files...[ ok . [....] Setting kernel variables ...[ ok done. [....] Configuring network interfaces...[ ok done. [....] Starting rpcbind daemon...[ ok . [....] Starting NFS common utilities: statd idmapd[ ok . [....] Cleaning up temporary files...[ ok . [....] Starting network benchmark server[ ok . INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting network benchmark server[FAIL failed! [....] Starting system message bus: dbus[ ok . [....] Starting rpcbind daemon...[....] Already running.[ ok . [....] Starting NFS common utilities: statd idmapd[ ok . Debian GNU/Linux wheezy/sid armel ttyO0 armel login: