U-Boot SPL 2014.07-rc2-00015-g713ff68 (Jun 03 2014 - 09:09:41) OMAP5432 ES2.0 SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! reading u-boot.img reading u-boot.img U-Boot 2014.07-rc2-00015-g713ff68 (Jun 03 2014 - 09:09:41), Build: jenkins-github_Bootloader-Builder-315 CPU : OMAP5432 ES2.0 Board: OMAP5432 uEVM I2C: ready DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: No ethernet found. Hit any key to stop autoboot: 5  0 U-Boot# U-Boot# setenv bootargs 'console=ttyO2,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh' U-Boot# loady 0x81000000 ## Ready for binary (ymodem) download to 0x81000000 at 115200 bps... CSending: uImage-dtb.omap5-uevm Sending: Transfer complete - CRC mode, 6(SOH)/3573(STX)/0(CAN) packets, 3 retries ## Total Size = 0x0037d5be = 3659198 Bytes U-Boot# bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3659134 Bytes = 3.5 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-rc2 (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Sun Dec 20 15:06:24 MST 2015 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI OMAP5 uEVM board [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0xfd800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OMAP4: Map 0xfee00000 to fe600000 for dram barrier [ 0.000000] On node 0 totalpages: 519680 [ 0.000000] free_area_init_node: node 0, pgdat c09d29c0, node_mem_map eee1d000 [ 0.000000] Normal zone: 1728 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 323072 pages, LIFO batch:31 [ 0.000000] OMAP5432 ES2.0 [ 0.000000] PERCPU: Embedded 14 pages/cpu @eedad000 s24936 r8192 d24216 u57344 [ 0.000000] pcpu-alloc: s24936 r8192 d24216 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517952 [ 0.000000] Kernel command line: console=ttyO2,115200n8 root=/dev/mmcblk1p2 rootwait fixrtc debug earlyprintk ignore_loglevel init=/bin/sh [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2024400K/2078720K available (6611K kernel code, 746K rwdata, 2240K rodata, 452K init, 8263K bss, 37936K reserved, 16384K cma-reserved, 1275904K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08acf68 (8852 kB) [ 0.000000] .init : 0xc08ad000 - 0xc091e000 ( 452 kB) [ 0.000000] .data : 0xc091e000 - 0xc09d8998 ( 747 kB) [ 0.000000] .bss : 0xc09db000 - 0xc11ecc70 (8264 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] Architected cp15 timer(s) running at 6.14MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16ac02862, max_idle_ns: 440795202218 ns [ 0.000004] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511085ns [ 0.000016] Switching to timer-based delay loop, resolution 162ns [ 0.000319] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000329] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001187] Console: colour dummy device 80x30 [ 0.001219] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.001227] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.001233] ... MAX_LOCK_DEPTH: 48 [ 0.001239] ... MAX_LOCKDEP_KEYS: 8191 [ 0.001246] ... CLASSHASH_SIZE: 4096 [ 0.001251] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.001257] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.001263] ... CHAINHASH_SIZE: 32768 [ 0.001269] memory used by lock dependency info: 5167 kB [ 0.001275] per task-struct memory footprint: 1536 bytes [ 0.001298] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440) [ 0.001311] pid_max: default: 32768 minimum: 301 [ 0.001573] Security Framework initialized [ 0.001674] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001686] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003794] Initializing cgroup subsys io [ 0.003858] Initializing cgroup subsys memory [ 0.003911] Initializing cgroup subsys devices [ 0.003966] Initializing cgroup subsys freezer [ 0.004045] Initializing cgroup subsys perf_event [ 0.004086] CPU: Testing write buffer coherency: ok [ 0.004926] /cpus/cpu@0 missing clock-frequency property [ 0.004946] /cpus/cpu@1 missing clock-frequency property [ 0.004957] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005013] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.009084] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.009494] Brought up 2 CPUs [ 0.009507] SMP: Total of 2 processors activated (24.57 BogoMIPS). [ 0.009514] CPU: All CPU(s) started in SVC mode. [ 0.012075] devtmpfs: initialized [ 0.053767] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.055083] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.056311] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.165298] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.166159] pinctrl core: initialized pinctrl subsystem [ 0.169572] NET: Registered protocol family 16 [ 0.173051] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.200490] cpuidle: using governor ladder [ 0.230475] cpuidle: using governor menu [ 0.240290] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.241424] OMAP GPIO hardware version 0.1 [ 0.242316] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.244014] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.245640] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.247280] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.248922] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.250595] gpiochip_add: registered GPIOs 192 to 223 on device: gpio [ 0.252250] gpiochip_add: registered GPIOs 224 to 255 on device: gpio [ 0.253452] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc' [ 0.253652] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 0.253668] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.253743] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x10000000 [ 0.258846] irq: no irq domain found for /ocp/l4@4a000000/scm@2800/pinmux@40 ! [ 0.261372] irq: no irq domain found for /ocp/l4@4a000000/scm@2800/pinmux@40 ! [ 0.279610] No ATAGs? [ 0.279666] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.279675] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.281364] OMAP DMA hardware revision 0.0 [ 0.331423] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver [ 0.332684] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator-mmcsd[0]' [ 0.333261] reg-fixed-voltage fixedregulator-mmcsdio: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_wlan_pins, deferring probe [ 0.336319] SCSI subsystem initialized [ 0.336643] libata version 3.00 loaded. [ 0.337194] usb_phy_generic hsusb2_phy: GPIO lookup for consumer reset [ 0.337204] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.337235] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb2_phy[0]' - status (0) [ 0.337285] no flags found for reset [ 0.337297] usb_phy_generic hsusb2_phy: GPIO lookup for consumer vbus-detect [ 0.337305] usb_phy_generic hsusb2_phy: using device tree for GPIO lookup [ 0.337315] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb2_phy[0]' [ 0.337326] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb2_phy[0]' [ 0.337334] usb_phy_generic hsusb2_phy: using lookup tables for GPIO lookup [ 0.337391] usb_phy_generic hsusb2_phy: lookup for GPIO vbus-detect failed [ 0.337441] hsusb2_phy supply vcc not found, using dummy regulator [ 0.337791] usb_phy_generic hsusb3_phy: GPIO lookup for consumer reset [ 0.337801] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.337825] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/hsusb3_phy[0]' - status (0) [ 0.337838] no flags found for reset [ 0.337848] usb_phy_generic hsusb3_phy: GPIO lookup for consumer vbus-detect [ 0.337856] usb_phy_generic hsusb3_phy: using device tree for GPIO lookup [ 0.337866] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpios' property of node '/hsusb3_phy[0]' [ 0.337875] of_get_named_gpiod_flags: can't parse 'vbus-detect-gpio' property of node '/hsusb3_phy[0]' [ 0.337883] usb_phy_generic hsusb3_phy: using lookup tables for GPIO lookup [ 0.337894] usb_phy_generic hsusb3_phy: lookup for GPIO vbus-detect failed [ 0.337929] hsusb3_phy supply vcc not found, using dummy regulator [ 0.338397] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c1_pins, deferring probe [ 0.339516] omap_i2c 48072000.i2c: bus 1 rev0.12 at 100 kHz [ 0.340295] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 0.341046] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 100 kHz [ 0.341120] omap_i2c 4807c000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c5_pins, deferring probe [ 0.341417] pps_core: LinuxPPS API ver. 1 registered [ 0.341425] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.341462] PTP clock support registered [ 0.344121] clocksource: Switched to clocksource arch_sys_counter [ 0.449607] NET: Registered protocol family 2 [ 0.450889] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.451015] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.453366] TCP: Hash tables configured (established 8192 bind 8192) [ 0.453509] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.453824] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.454766] NET: Registered protocol family 1 [ 0.455665] RPC: Registered named UNIX socket transport module. [ 0.455675] RPC: Registered udp transport module. [ 0.455683] RPC: Registered tcp transport module. [ 0.455690] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.495217] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.499341] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.499592] audit: initializing netlink subsys (disabled) [ 0.499702] audit: type=2000 audit(0.490:1): initialized [ 0.502143] VFS: Disk quotas dquot_6.6.0 [ 0.502249] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.503941] NFS: Registering the id_resolver key type [ 0.504208] Key type id_resolver registered [ 0.504217] Key type id_legacy registered [ 0.504336] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.507469] bounce: pool size: 64 pages [ 0.507518] io scheduler noop registered [ 0.507531] io scheduler deadline registered [ 0.507562] io scheduler cfq registered (default) [ 0.510938] ti-pipe3 4a096000.phy: can't get syscon-pllreset, sata dpll won't idle [ 0.512410] pinctrl-single 4a002840.pinmux: 219 pins at pa fc002840 size 438 [ 0.512851] pinctrl-single 4ae0c840.pinmux: 28 pins at pa fce0c840 size 56 [ 0.517887] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.522105] omap_uart 4806a000.serial: no wakeirq for uart0 [ 0.522120] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 0.522400] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 306, base_baud = 3000000) is a OMAP UART0 [ 0.523485] omap_uart 4806c000.serial: no wakeirq for uart1 [ 0.523498] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 0.523681] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 307, base_baud = 3000000) is a OMAP UART1 [ 0.524604] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48020000[0]' [ 0.524795] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 308, base_baud = 3000000) is a OMAP UART2 [ 1.702126] console [ttyO2] enabled [ 1.706664] omap_uart 4806e000.serial: no wakeirq for uart3 [ 1.712495] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 1.722524] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 309, base_baud = 3000000) is a OMAP UART3 [ 1.733132] omap_uart 48066000.serial: no wakeirq for uart4 [ 1.739024] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48066000[0]' [ 1.749074] 48066000.serial: ttyO4 at MMIO 0x48066000 (irq = 310, base_baud = 3000000) is a OMAP UART4 [ 1.759643] omap_uart 48068000.serial: no wakeirq for uart5 [ 1.765499] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@48068000[0]' [ 1.775529] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 311, base_baud = 3000000) is a OMAP UART5 [ 1.809501] brd: module loaded [ 1.827752] loop: module loaded [ 1.833204] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 1.840258] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.849200] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 1.861338] scsi host0: ahci [ 1.865201] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 338 [ 1.874364] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.890678] mousedev: PS/2 mouse device common for all mice [ 1.896537] i2c /dev entries driver [ 1.902543] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 1.908843] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.915688] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.925258] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.934731] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.941739] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 1.947852] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 1.954148] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 1.960971] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 1.970531] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 1.980003] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 1.987024] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 2.024984] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 2.031268] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 2.038146] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.047718] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.057186] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.064210] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 2.070311] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 2.076605] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 2.083433] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 2.092993] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 2.102461] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 2.109477] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 2.154385] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.160697] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.167581] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.177153] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.186662] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.193698] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.200528] ledtrig-cpu: registered to indicate activity on CPUs [ 2.208591] oprofile: using timer interrupt. [ 2.213441] Initializing XFRM netlink socket [ 2.218188] NET: Registered protocol family 10 [ 2.224100] ata1: SATA link down (SStatus 0 SControl 300) [ 2.224488] sit: IPv6 over IPv4 tunneling driver [ 2.226024] NET: Registered protocol family 17 [ 2.226071] NET: Registered protocol family 15 [ 2.226279] Key type dns_resolver registered [ 2.226424] omap_vc_init_channel: No PMIC info for vdd_core [ 2.226428] omap_vp_init: No PMIC info for vdd_core [ 2.226443] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.226445] omap_vp_init: No PMIC info for vdd_mm [ 2.226458] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.226461] omap_vp_init: No PMIC info for vdd_mpu [ 2.227101] Power Management for TI OMAP4+ devices. [ 2.227335] ThumbEE CPU extension supported. [ 2.227355] Registering SWP/SWPB emulation handler [ 2.227370] SmartReflex Class3 initialized [ 2.245194] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixedregulator-mmcsdio[0]' - status (0) [ 2.248735] palmas 0-0048: Irq flag is 0x00000000 [ 2.277667] mmc0: MAN_BKOPS_EN bit is not set [ 2.279606] mmc0: new high speed MMC card at address 0001 [ 2.281429] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.282093] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.282700] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.344646] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.402409] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.410094] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.416343] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 2.422638] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.429503] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.439098] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 2.448609] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 2.455667] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 2.461788] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 2.468107] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 2.474971] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 2.484565] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 2.494062] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 2.501089] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 2.544642] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.550940] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.557811] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.567408] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.576911] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.583941] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.592214] hctosys: unable to open rtc device (rtc0) [ 2.597547] sr_init: No PMIC hook to init smartreflex [ 2.603078] sr_init: platform driver register failed for SR [ 2.637623] vmmcsdio_fixed: disabling [ 2.642633] ldo3: disabling [ 2.646624] ldo8: disabling [ 2.652247] Waiting for root device /dev/mmcblk1p2... [ 2.672691] mmc1: host does not support reading read-only switch, assuming write-enable [ 2.681252] mmc1: new SD card at address d91a [ 2.686990] mmcblk1: mmc1:d91a SU02G 1.84 GiB [ 2.693823] mmcblk1: p1 p2 [ 2.699360] omap_hsmmc 480ad000.mmc: GPIO lookup for consumer wp [ 2.705697] omap_hsmmc 480ad000.mmc: using device tree for GPIO lookup [ 2.712548] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480ad000[0]' [ 2.722146] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480ad000[0]' [ 2.731649] omap_hsmmc 480ad000.mmc: using lookup tables for GPIO lookup [ 2.738700] omap_hsmmc 480ad000.mmc: lookup for GPIO wp failed [ 2.765754] EXT4-fs (mmcblk1p2): couldn't mount as ext3 due to feature incompatibilities [ 2.794459] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.803017] VFS: Mounted root (ext4 filesystem) readonly on device 179:26. [ 2.822995] devtmpfs: mounted [ 2.826552] Freeing unused kernel memory: 452K (c08ad000 - c091e000) /bin/sh: 0: can't access tty; job control turned off # # #