U-Boot 1.1.4 (Mar 18 2007 - 12:22:00) OMAP2430C-GP revision 3, PRCM #5A TI 2430SDP 1.1 Version + mDDR (Boot NOR) DRAM: 128 MB Flash: 192 MB NAND:64 MB In: serial Out: serial Err: serial Hit any key to stop autoboot: 3  0 OMAP243X SDP # OMAP243X SDP # setenv bootargs console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh OMAP243X SDP # loady ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... CSending: uImage-dtb.omap2430-sdp Sending: Transfer complete odem - CRC mode, 2(SOH)/3566(STX)/0(CAN) packets, 3 retries ## Total Size = 0x0037b7f3 = 3651571 Bytes OMAP243X SDP # bootm ## Booting image at 80000000 ... Image Name: Linux- Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3651507 Bytes = 3.5 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... %% Start PM consolidated quick test (retention only) %% Preparation [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-rc4 (paul@nozomi) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Sun Dec 20 16:29:30 MST 2015 [ 0.000000] CPU: ARMv6-compatible processor [4107b366] revision 6 (ARMv6TEJ), cr=00c5387d [ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: TI OMAP2430 SDP [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] cma: Reserved 16 MiB at 0x86800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 32256 [ 0.000000] free_area_init_node: node 0, pgdat c09d4ac0, node_mem_map c7cd1000 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32256 pages, LIFO batch:7 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] OMAP2430 [ 0.000000] [ 0.000000] PERCPU: Embedded 14 pages/cpu @c7c6d000 s24936 r8192 d24216 u57344 [ 0.000000] pcpu-alloc: s24936 r8192 d24216 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 31968 [ 0.000000] Kernel command line: console=ttyO0,115200n8 ignore_loglevel earlyprintk root=/dev/mmcblk0p1 rootwait init=/bin/sh [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 92548K/129024K available (6619K kernel code, 746K rwdata, 2240K rodata, 452K init, 8263K bss, 20092K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08aef60 (8860 kB) [ 0.000000] .init : 0xc08af000 - 0xc0920000 ( 452 kB) [ 0.000000] .data : 0xc0920000 - 0xc09daa98 ( 747 kB) [ 0.000000] .bss : 0xc09dd000 - 0xc11eec68 (8264 kB) [ 0.000000] Running RCU self tests [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU lockdep checking is enabled. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa0fe000 (revision 3.0) with 96 interrupts [ 0.000000] Clocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns [ 0.000061] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000823] hw-breakpoint: CPUID feature registers not supported. Assuming v6 debug is present. [ 0.004669] Console: colour dummy device 80x30 [ 0.004882] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.004913] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.004943] ... MAX_LOCK_DEPTH: 48 [ 0.004974] ... MAX_LOCKDEP_KEYS: 8191 [ 0.005004] ... CLASSHASH_SIZE: 4096 [ 0.005035] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.005065] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.005065] ... CHAINHASH_SIZE: 32768 [ 0.005096] memory used by lock dependency info: 5167 kB [ 0.005126] per task-struct memory footprint: 1536 bytes [ 0.005218] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816) [ 0.071197] pid_max: default: 32768 minimum: 301 [ 0.072509] Security Framework initialized [ 0.072998] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.073059] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.085052] Initializing cgroup subsys io [ 0.085418] Initializing cgroup subsys memory [ 0.085662] Initializing cgroup subsys devices [ 0.085998] Initializing cgroup subsys freezer [ 0.086486] Initializing cgroup subsys perf_event [ 0.086730] CPU: Testing write buffer coherency: ok [ 0.092102] missing device node for CPU 0 [ 0.092163] CPU0: thread -1, cpu 0, socket -1, mpidr 4107b366 [ 0.092498] Setting up static identity map for 0x80008280 - 0x800082f0 [ 0.106933] Brought up 1 CPUs [ 0.106994] SMP: Total of 1 processors activated (262.96 BogoMIPS). [ 0.107025] CPU: All CPU(s) started in SVC mode. [ 0.119262] devtmpfs: initialized [ 0.310211] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2 [ 0.432098] omap_hwmod: usb_otg_hs: _wait_target_ready failed: -16 [ 0.432159] omap_hwmod: usb_otg_hs: cannot be enabled for reset (3) [ 0.455108] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.462463] pinctrl core: initialized pinctrl subsystem [ 0.482269] NET: Registered protocol family 16 [ 0.505828] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.513275] cpuidle: using governor ladder [ 0.513397] cpuidle: using governor menu [ 0.588592] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.593444] OMAP GPIO hardware version 2.4 [ 0.597625] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.605224] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.612915] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.620635] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.626983] omap-gpmc 6e000000.gpmc: GPMC revision 3.0 [ 0.627532] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.644622] No ATAGs? [ 0.644805] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.644866] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.648834] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.648895] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.652252] OMAP DMA hardware revision 4.0 [ 0.772796] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver [ 0.788940] SCSI subsystem initialized [ 0.791168] libata version 3.00 loaded. [ 0.800323] omap_i2c 48070000.i2c: bus 0 rev3.3 at 100 kHz [ 0.805755] omap_i2c 48072000.i2c: bus 1 rev3.3 at 100 kHz [ 0.807220] pps_core: LinuxPPS API ver. 1 registered [ 0.807281] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.807495] PTP clock support registered [ 0.822814] clocksource: Switched to clocksource 32k_counter [ 1.373138] NET: Registered protocol family 2 [ 1.379669] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.379821] TCP bind hash table entries: 1024 (order: 3, 36864 bytes) [ 1.381225] TCP: Hash tables configured (established 1024 bind 1024) [ 1.381866] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.382904] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.386535] NET: Registered protocol family 1 [ 1.392150] RPC: Registered named UNIX socket transport module. [ 1.392211] RPC: Registered udp transport module. [ 1.392272] RPC: Registered tcp transport module. [ 1.392486] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.399200] hw perfevents: enabled with armv6_1136 PMU driver, 3 counters available [ 1.420196] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.421112] audit: initializing netlink subsys (disabled) [ 1.421783] audit: type=2000 audit(1.410:1): initialized [ 1.437408] VFS: Disk quotas dquot_6.6.0 [ 1.437896] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.447418] NFS: Registering the id_resolver key type [ 1.448913] Key type id_resolver registered [ 1.448974] Key type id_legacy registered [ 1.449707] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.471679] io scheduler noop registered [ 1.471771] io scheduler deadline registered [ 1.471954] io scheduler cfq registered (default) [ 1.481842] pinctrl-single 49002030.pinmux: 340 pins at pa fb002030 size 340 [ 1.495758] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.518463] omap_uart 4806a000.serial: no wakeirq for uart0 [ 1.518554] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806a000[0]' [ 1.520080] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0 [ 2.383758] console [ttyO0] enabled [ 2.395080] omap_uart 4806c000.serial: no wakeirq for uart1 [ 2.401000] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806c000[0]' [ 2.412139] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1 [ 2.426696] omap_uart 4806e000.serial: no wakeirq for uart2 [ 2.432830] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp/serial@4806e000[0]' [ 2.443817] 4806e000.serial: ttyO2 at MMIO 0x4806e000 (irq = 90, base_baud = 3000000) is a OMAP UART2 [ 2.597412] brd: module loaded [ 2.683319] loop: module loaded [ 2.728881] twl 1-0048: PIH (irq 23) chaining IRQs 274..282 [ 2.736297] twl 1-0048: power (irq 279) chaining IRQs 282..289 [ 2.920684] twl4030_gpio twl4030-gpio: gpio (irq 274) chaining IRQs 290..307 [ 2.930694] gpiochip_find_base: found new base at 494 [ 2.937835] gpiochip_add: registered GPIOs 494 to 511 on device: twl4030 [ 2.969818] mtdoops: mtd device (mtddev=name/number) must be supplied [ 3.006378] smc91x 8000300.ethernet: GPIO lookup for consumer power [ 3.013153] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.020111] of_get_named_gpiod_flags: can't parse 'power-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.031494] of_get_named_gpiod_flags: can't parse 'power-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.042785] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.050323] smc91x 8000300.ethernet: lookup for GPIO power failed [ 3.056915] smc91x 8000300.ethernet: GPIO lookup for consumer reset [ 3.063629] smc91x 8000300.ethernet: using device tree for GPIO lookup [ 3.070556] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.081939] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/gpmc@6e000000/ethernet@gpmc[0]' [ 3.093261] smc91x 8000300.ethernet: using lookup tables for GPIO lookup [ 3.100341] smc91x 8000300.ethernet: lookup for GPIO reset failed [ 3.107269] smc91x 8000300.ethernet (unnamed net_device) (uninitialized): smc91x: IOADDR c88fa300 doesn't match configuration (0). [ 3.119842] smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre [ 3.135131] smc91x 8000300.ethernet eth0: SMC91C94 (rev 9) at c88fa300 IRQ 261 [ 3.142913] [ 3.144561] smc91x 8000300.ethernet eth0: Ethernet addr: 10:03:31:33:16:8f [ 3.168579] mousedev: PS/2 mouse device common for all mice [ 3.174743] i2c /dev entries driver [ 3.190399] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer cd [ 3.197052] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 3.204071] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.213867] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@4809c000[0]' [ 3.223510] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 3.230621] omap_hsmmc 4809c000.mmc: lookup for GPIO cd failed [ 3.236907] omap_hsmmc 4809c000.mmc: GPIO lookup for consumer wp [ 3.243347] omap_hsmmc 4809c000.mmc: using device tree for GPIO lookup [ 3.250244] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@4809c000[0]' [ 3.259979] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@4809c000[0]' [ 3.269592] omap_hsmmc 4809c000.mmc: using lookup tables for GPIO lookup [ 3.276794] omap_hsmmc 4809c000.mmc: lookup for GPIO wp failed [ 3.334106] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd [ 3.340454] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.347534] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.357299] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.366943] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.374114] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed [ 3.380310] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp [ 3.386749] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup [ 3.393768] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/mmc@480b4000[0]' [ 3.403503] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/mmc@480b4000[0]' [ 3.413116] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup [ 3.420227] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed [ 3.464172] ledtrig-cpu: registered to indicate activity on CPUs [ 3.475311] oprofile: using arm/armv6 [ 3.481719] Initializing XFRM netlink socket [ 3.487731] NET: Registered protocol family 10 [ 3.504180] sit: IPv6 over IPv4 tunneling driver [ 3.517333] NET: Registered protocol family 17 [ 3.522308] NET: Registered protocol family 15 [ 3.528533] Key type dns_resolver registered [ 3.533843] SmartReflex Class3 initialized [ 3.569030] hctosys: unable to open rtc device (rtc0) [ 3.574645] sr_init: No PMIC hook to init smartreflex [ 3.580902] sr_init: platform driver register failed for SR [ 3.720306] VUSB1V5: disabling [ 3.726928] VUSB1V8: disabling [ 3.733612] VUSB3V1: disabling [ 3.751159] Waiting for root device /dev/mmcblk0p1...