ĉ€˜€ĉ€˜€`f†fĉĝ˜†ž~f~ĉžf†ž`ĉĝfž˜ŝžxf†ĝ˜à†f††f†˜x˜àx˜žx~`˜à~˜à˜˜˜˜€fxĉxàžff˜ĉ€˜€f†fx†žĝž~àĉžŝž`˜ĝfx~ŝžf€˜€à˜ŝžx†žĝž~˜ĉf†ĉžŝž`††fžĝžxĉžĉž˜žfžf€˜€ U-Boot 2011.06-00001-ge147603 (Sep 07 2012 - 22:19:41) OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 512 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0 In: serial Out: serial Err: serial Beagle xM Rev A No EEPROM on expansion board Die ID #2fa800001bf00000015739ea0702a01d Hit any key to stop autoboot: 3  0 OMAP3 beagleboard.org # OMAP3 beagleboard.org # loady ## Ready for binary (ymodem) download to 0x80200000 at 230400 bps... C ## Total Size = 0x003dcf58 = 4050776 Bytes OMAP3 beagleboard.org # OMAP3 beagleboard.org # OMAP3 beagleboard.org # OMAP3 beagleboard.org # setenv bootargs console=ttyO2,230400 vram=12M root=/dev/mmcblk0p2 rw mmcrootfstype= OMAP3 beagleboard.org # ext3 rootwait earlyprintk debug ignore_loglevel Unknown command 'ext3' - try 'help' OMAP3 beagleboard.org # setenv bootargs console=ttyO2,230400 vram=12M root=/dev/mmcblk0p2 rw mmcrootfstype=ext3 rootwait earlyprintk debug ignore_loglevel OMAP3 beagleboard.org # bootm ## Booting kernel from Legacy Image at 80200000 ... Image Name: Linux-3.6.0-rc6-00003-gb19fd98 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4050712 Bytes = 3.9 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.6.0-rc6-00003-gb19fd98 (paul@dusk) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #424 SMP Sat Sep 22 22:54:43 MDT 2012 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Reserving 12582912 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 127744 [ 0.000000] free_area_init_node: node 0, pgdat c07c19c0, node_mem_map c0d1f000 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 126720 pages, LIFO batch:31 [ 0.000000] OMAP3630 ES1.0 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/331/600 MHz [ 0.000000] PERCPU: Embedded 9 pages/cpu @c1127000 s12736 r8192 d15936 u36864 [ 0.000000] pcpu-alloc: s12736 r8192 d15936 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126720 [ 0.000000] Kernel command line: console=ttyO2,230400 vram=12M root=/dev/mmcblk0p2 rw mmcrootfstype=ext3 rootwait earlyprintk debug ignore_loglevel [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 499MB = 499MB total [ 0.000000] Memory: 492976k/492976k available, 31312k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc06d6acc (6971 kB) [ 0.000000] .init : 0xc06d7000 - 0xc07261c0 ( 317 kB) [ 0.000000] .data : 0xc0728000 - 0xc07c41c0 ( 625 kB) [ 0.000000] .bss : 0xc07c41e4 - 0xc0d1e24c (5481 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:474 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.000885] Calibrating delay loop... 320.37 BogoMIPS (lpj=1253376) [ 0.088256] pid_max: default: 32768 minimum: 301 [ 0.088775] Security Framework initialized [ 0.088958] Mount-cache hash table entries: 512 [ 0.093841] CPU: Testing write buffer coherency: ok [ 0.094848] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.094909] Setting up static identity map for 0x80500730 - 0x805007a0 [ 0.097198] Brought up 1 CPUs [ 0.097229] SMP: Total of 1 processors activated (320.37 BogoMIPS). [ 0.109039] ttyO2 used as console in debug mode uart2 clocks will not be gated [ 0.118835] dummy: [ 0.121215] NET: Registered protocol family 16 [ 0.122100] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.123138] GPMC revision 5.0 [ 0.123382] gpmc: irq-20 could not claim: err -22 [ 0.134307] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.134857] OMAP GPIO hardware version 2.5 [ 0.136383] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.138366] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.140472] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.142059] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.143737] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.151092] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.154113] OMAP3 Beagle Rev: xM Ax/Bx [ 0.168243] _omap_mux_get_by_name: Could not find signal uart4_rx.uart4_rx [ 0.177337] Reprogramming SDRC clock to 331882352 Hz [ 0.178283] Found NAND on CS0 [ 0.178314] Registering NAND on CS0 [ 0.179931] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.197204] omap-mcbsp.2: alias fck already exists [ 0.198120] omap-mcbsp.3: alias fck already exists [ 0.203277] OMAP DMA hardware revision 5.0 [ 0.273345] bio: create slab at 0 [ 0.372650] omap-dma-engine omap-dma-engine: OMAP DMA engine driver [ 0.379028] SCSI subsystem initialized [ 0.381866] usbcore: registered new interface driver usbfs [ 0.382476] usbcore: registered new interface driver hub [ 0.383178] usbcore: registered new device driver usb [ 0.397430] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz [ 0.407501] twl 1-0048: PIH (irq 7) chaining IRQs 320..328 [ 0.408203] twl 1-0048: power (irq 325) chaining IRQs 328..335 [ 0.411224] twl4030_gpio twl4030_gpio: gpio (irq 320) chaining IRQs 336..353 [ 0.412719] gpiochip_add: registered GPIOs 192 to 211 on device: twl4030 [ 0.420471] vdd_mpu_iva: 600 <--> 1450 mV normal [ 0.423126] vdd_core: 600 <--> 1450 mV normal [ 0.425598] VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby [ 0.428070] VDAC: 1800 mV normal standby [ 0.430816] VDVI: 1800 mV normal standby [ 0.433441] VSIM: 1800 <--> 3000 mV at 1800 mV normal standby [ 0.434967] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 100 kHz [ 0.445251] Switching to clocksource 32k_counter [ 0.585662] NET: Registered protocol family 2 [ 0.588409] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.589111] TCP bind hash table entries: 16384 (order: 7, 589824 bytes) [ 0.598236] TCP: Hash tables configured (established 16384 bind 16384) [ 0.598419] TCP: reno registered [ 0.598480] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 0.598785] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 0.599761] NET: Registered protocol family 1 [ 0.601196] RPC: Registered named UNIX socket transport module. [ 0.601226] RPC: Registered udp transport module. [ 0.601257] RPC: Registered tcp transport module. [ 0.601257] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.603088] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.782958] VFS: Disk quotas dquot_6.5.2 [ 0.783264] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.786376] NFS: Registering the id_resolver key type [ 0.786865] Key type id_resolver registered [ 0.786895] Key type id_legacy registered [ 0.787048] jffs2: version 2.2. (NAND) (SUMMARY) Âİ 2001-2006 Red Hat, Inc. [ 0.787658] msgmni has been set to 962 [ 0.791748] io scheduler noop registered [ 0.791778] io scheduler deadline registered [ 0.791870] io scheduler cfq registered (default) [ 0.794586] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.802032] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 0.804107] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 0.805999] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 [ 1.204864] console [ttyO2] enabled [ 1.208618] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3 [ 1.248626] brd: module loaded [ 1.271789] loop: module loaded [ 1.281951] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.286132] NAND device: Manufacturer ID: 0x20, Chip ID: 0xba (ST Micro NAND 256MiB 1,8V 16-bit), page size: 2048, OOB size: 64 [ 1.292541] Creating 5 MTD partitions on "omap2-nand.0": [ 1.295440] 0x000000000000-0x000000080000 : "X-Loader" [ 1.305938] 0x000000080000-0x000000260000 : "U-Boot" [ 1.314514] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.322265] 0x000000280000-0x000000680000 : "Kernel" [ 1.331329] 0x000000680000-0x000010000000 : "File System" [ 1.434417] OneNAND driver initializing [ 1.451385] usbcore: registered new interface driver asix [ 1.455230] usbcore: registered new interface driver cdc_ether [ 1.459014] usbcore: registered new interface driver smsc95xx [ 1.463043] usbcore: registered new interface driver net1080 [ 1.466674] usbcore: registered new interface driver cdc_subset [ 1.470611] usbcore: registered new interface driver zaurus [ 1.474243] usbcore: registered new interface driver cdc_ncm [ 1.479827] usbcore: registered new interface driver cdc_wdm [ 1.482910] Initializing USB Mass Storage driver... [ 1.486389] usbcore: registered new interface driver usb-storage [ 1.489654] USB Mass Storage support registered. [ 1.493591] usbcore: registered new interface driver libusual [ 1.497375] usbcore: registered new interface driver usbtest [ 1.502319] mousedev: PS/2 mouse device common for all mice [ 1.511657] input: twl4030_pwrbutton as /devices/platform/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0 [ 1.520294] twl_rtc twl_rtc: Power up reset detected. [ 1.523254] twl_rtc twl_rtc: Enabling TWL-RTC [ 1.529785] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 1.534912] i2c /dev entries driver [ 1.540191] Driver for 1-wire Dallas network protocol. [ 1.546417] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 1.551574] twl4030_wdt twl4030_wdt: Failed to register misc device [ 1.555267] twl4030_wdt: probe of twl4030_wdt failed with error -16 [ 1.563049] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk [ 1.566375] omap-dma-engine omap-dma-engine: allocating channel for 62 [ 1.570007] omap-dma-engine omap-dma-engine: allocating channel for 61 [ 1.953430] usbcore: registered new interface driver usbhid [ 1.956756] usbhid: USB HID core driver [ 1.958831] oprofile: hardware counters not available [ 1.961639] oprofile: using timer interrupt. [ 1.964782] TCP: cubic registered [ 1.966583] Initializing XFRM netlink socket [ 1.969177] NET: Registered protocol family 17 [ 1.971710] NET: Registered protocol family 15 [ 1.974517] Key type dns_resolver registered [ 1.977111] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.992645] ThumbEE CPU extension supported. [ 2.028869] clock: disabling unused clocks to save power [ 2.036529] VDVI: incomplete constraints, leaving on [ 2.039581] VDAC: incomplete constraints, leaving on [ 2.047973] input: gpio-keys as /devices/platform/gpio-keys/input/input1 [ 2.055480] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.064086] Waiting for root device /dev/mmcblk0p2... [ 2.387207] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.394744] mmc0: new high speed SDHC card at address 1234 [ 2.400756] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 2.410980] mmcblk0: p1 p2 [ 5.350616] kjournald starting. Commit interval 5 seconds [ 5.354248] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended [ 5.759979] EXT3-fs (mmcblk0p2): using internal journal [ 5.771118] EXT3-fs (mmcblk0p2): recovery complete [ 5.773803] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 5.777954] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 5.781860] Freeing init memory: 316K INIT: version 2.86 booting Starting the hotplug events dispatcher udevd [ 6.798309] udevd (732): /proc/732/oom_adj is deprecated, please use /proc/732/oom_score_adj instead. Synthesizing the initial hotplug events Remounting root file system... mount: according to mtab, /proc is already mounted on /proc WARNING: Couldn't open directory /lib/modules/3.6.0-rc6-00003-gb19fd98: No such file or directory FATAL: Could not open /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep.temp for writing: No such file or directory root: mount: mount point /proc/bus/usb does not exist Setting up IP spoofing protection: rp_filter. Configuring network interfaces... modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory ifconfig: SIOCGIFFLAGS: No such device modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory eth0 No such device modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory udhcpc: SIOCGIFINDEX: No such device done. Starting portmap daemon: portmap. Tue Jul 22 00:18:00 UTC 2008 INIT: Entering runlevel: 5 ALSA: Restoring mixer settings... /usr/sbin/alsactl: load_state:1327: No soundcards found... Starting Dropbear SSH server: modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory dropbear. Starting advanced power management daemon: No APM support in kernel (failed.) Starting system message bus: dbus. Starting syslogd/klogd: start-stop-daemon: lseek: Invalid argument * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] Starting Bluetooth subsystem: hcidmodprobe: FATAL: Could not load /lib/modules/3.6.0-rc6-00003-gb19fd98/modules.dep: No such file or directory hid2hci. .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: root login[2034]: root login on `ttyO2' root@beagleboard:~# uptime 03:00:56 up 2:43, 1 user, load average: 0.00, 0.01, 0.05 root@beagleboard:~# .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyO2 Angstrom 2008.1-test-20080712 beagleboard ttyO2 beagleboard login: